2006 YAMAHA YZ85 brake light

GEN
INFO
1 - 1
DESCRIPTION
EC100000
GENERAL INFORMATION
EC110000
DESCRIPTION
1Clutch lever
2Engine stop switch
3Front brake lever
4Throttle grip
5Fuel tank cap
6Radiator cap
7Kickstarter crank
8Fuel tank
9Coolant drain bolt
0Rear brake pedal
ARadiator
BValve joint
CFuel cock
DAir filter
EDrive chain
FShift pedal
GStarter knob
HFront forkNOTE:

The machine you have purchased may differ
slightly from those shown in the following.

Designs and specifications are subject to
change without notice.
5PA10020
5PA10010
5PAR0001

2 - 17
SPEC
1Sub-wire harness
2CDI unit
3Ignition coil
4Clutch cable
5Cable guide
6Transmission oil breather hose
7CDI unit band
8Clamp
9Brake hose
0Brake hose holder
AHose guide
BReservoir hose
CReservoir tank
DBrake master cylinderÈPass the transmission oil breather hose through
the hose guide.
ÉClamp the sub-wire harness at the tape on it
within the arrow mark.
ÊPass the sub-wire harness on the left of the CDI
unit.
ËPass the reservoir hose between the brake hose
and swingarm bracket.
ÌPass the reservoir hose through the hose guides.
ÍInstall the brake hose so that its pipe portion
directs as shown and lightly touches the projec-
tion on the brake master cylinder.
CABLE ROUTING DIAGRAM

3 - 35
INSP
ADJ
LUBRICATION
LUBRICATION
To ensure smooth operation of all compo-
nents, lubricate your machine during setup,
after break-in, and after every race.
1All control cable
2Clutch lever pivot
3Shift pedal pivot
4Footrest pivot
5Throttle-to-handlebar contact
6Drive chain
7Tube guide cable winding portion
8Throttle cable end
9Clutch cable endÈUse Yamaha cable lube or equivalent on these
areas.
ÉUse SAE 10W-30 motor oil or suitable chain
lubricants.
ÊLubricate the following areas with high quality,
lightweight lithium-soap base grease.
CAUTION:
Wipe off any excess grease, and avoid get-
ting grease on the brake discs.
AAA
AAB
CC
5PA307705PA307805PA30790
5PA308005PA308105PA30820
5PA308005PA30840

5 - 22
CHAS
Front brake hose
1. Install:

Copper washer 1

Brake hose 2

Union bolt 3
WARNING
Always use new copper washers.
CAUTION:
Install the brake hose so that its pipe por-
tion a directs as shown and lightly
touches the projection b on the brake
master cylinder.
5PA50660
T R..30 Nm (3.0 m · kg, 22 ft · lb)
5PA50670
2. Install:

Protector 1

Bolt (protector) 2
NOTE:
Fit the brake hose into the guides a of the pro-
tector.
5PA50680
T R..7 Nm (0.7 m · kg, 5.1 ft · lb)
3. Install:

Brake hose holder 1

Bolt (brake hose holder) 2
NOTE:

Align the brake hose holder with the projec-
tion a on the front fork and clamp the brake
hose.

Pass the brake hose behind the rib b on the
front fork.
5PA50690
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)
FRONT BRAKE AND REAR BRAKE

5 - 23
CHAS
4. Install:

Copper washer 1

Brake hose 2

Union bolt 3
WARNING
Always use new copper washers.
CAUTION:
Install the brake hose so that its pipe por-
tion a lightly touches the projection b on
the brake caliper.
5PA50700
5PA50710
T R..26 Nm (2.6 m · kg, 19 ft · lb)
Rear brake hose
1. Install:

Copper washer 1

Brake hose 2

Union bolt 3
WARNING
Always use new copper washers.
CAUTION:
Install the brake hose so that its pipe por-
tion a directs as shown and lightly
touches the projection b on the brake
master cylinder.
5PA50720
5PA50730
T R..26 Nm (2.6 m · kg, 19 ft · lb)
FRONT BRAKE AND REAR BRAKE

5 - 24
CHAS
2. Install:

Copper washer 1

Brake hose 2

Union bolt 3
WARNING
Always use new copper washers.
CAUTION:
Install the brake hose so that its pipe por-
tion a lightly touches the projection b on
the brake caliper.
5PA50740
5PA50750
T R..26 Nm (2.6 m · kg, 19 ft · lb)
3. Install:

Brake hose holder 1

Screw (brake hose holder) 2
5PA50760
T R..1 Nm (0.1 m · kg, 0.7 ft · lb)
FRONT BRAKE AND REAR BRAKE