2006 YAMAHA YZ250LC oil

3-37
LUBRICATION
INSP
ADJ
EC36a042
LUBRICATION
To ensure smooth operation of all components,
lubricate your machine during setup, after break-
in, and after every race.
1All control cable
2Clutch lever pivot
3Shift pedal pivot
4Footrest pivot
5Throttle-to-handlebar contact
6Drive chain
7Throttle roller cable guide
8Throttle roller sliding surface
9Tube guide cable winding portion
0Throttle cable end
qClutch cable endÅUse Yamaha cable lube or equivalent on
these areas.
ıUse SAE10W-30 motor oil or suitable chain
lubricants.
ÇLubricate the following areas with high quali-
ty, lightweight lithium-soap base grease.
cC
Wipe off any excess grease, and avoid getting
grease on the brake discs.
A
A
CC
AB
AA
1P8-9-31-3B 5/13/05 11:44 AM Page 38

4-12
CARBURATEUR ET SOUPAPE FLEXIBLE
VERGASER UND ZUNGENVENTIL
CARBURATORE E VALVOLA A LAMELLAENG
9Hauteur de la butée de soupape
b
Hors spécification Régler/
Changer la butée de clapet.9Altezza del fermo della valvola
b
Fuori specificaRegolare fermo
/Sostituire fermo della valvola.
IC465000
MONTAGGIO E
INSTALLAZIONE
IC465173
Valvola a lamella
1. Installare:
9Valvola a lamella 1
9Fermo (valvola a lamella) 2
9Vite (valvola a lamella) 3
NOTA:
9Installare la valvola a lamella con la
curvatura della valvola a lamella
come illustrato.
9Notare il taglio anell’angolo inferio-
re della lamella e della piastra del
fermo.
iI
Serrare gradualmente ciascuna vite
per evitare svergolamenti.
9Ventilanschlaghöhe b
Abweichung von Spezifikation
 Anschlag einstellen/ Ven-
tilanschlag erneuern.
MONTAGE UND EINBAU
Zungenventil
1. Einbauen:
9Zungenventil 1
9Anschlag (Zungenventil) 2
9Schraube (Zungenventil) 3
HINWEIS:
9Das Zungenventil so einbauen, dass
die Biegung des Zungenventils
gemäß Abbildung angeordnet ist.
9Es ist darauf zu achten, dass der
Ausschnitt aan der unteren Ecke
der Ventilzunge richtig am Ventilan-
schag positioniert ist.
dD
Die Schrauben allmählich festzie-
hen, um ein Verziehen des Ventils
zu vermeiden.
REMONTAGE ET
MONTAGE
Soupape flexible
1. Monter:
9Soupape flexible 1
9Butée (soupape flexible) 2
9Vis (soupape flexible) 3
N.B.:
9Mettre la lame soupape avec la cour-
bure de lame soupape de la manière
indiquée.
9Noter l’entaille adans le coin infé-
rieur de la soupape et de la plaque de
butée.
fF
Serrer les vis granduellement pour
éviter de voiler le dispositif.
Ventilanschlaghöhe:
10,3~10,7 mm
(0,406~0,421 in)
1 Nm (0,1 m•kg, 0,7 ft•lb)
Altezza del fermo della
valvola:
10,3~10,7 mm
(0,406~0,421 in)
1 Nm (0,1 m•kg, 0,7 ft•lb)
1 Nm (0,1 m•kg, 0,7 ft•lb)
Hauteur de la butée de
soupape:
10,3~10,7 mm
(0,406~0,421 in)
IC464701Valvola a lamella
1. Misurare:
9Curvatura della valvola a lamel-
la a
Fuori specificaSostituirla.Zungenventil
1. Messen:
9Verbiegung des Zungenventils
a
Abweichung von Spezifikation
Erneuern. Schwimmer
1. Prüfen:
9Schwimmer 1
BeschädigungErneuern.
Flotteur
1. Examiner:
9Flotteur 1
EndommagementChanger.
Soupape flexible
1. Mesurer:
9Torsion de la soupape flexible
a
Hors spécificationChanger.IC464600Galleggiante
1. Ispezionare
9Galleggiante 1
DanniSostituirlo.
Verbiegungsgrenze des
Zungenventils:
0,2 mm (0,008 in)
Limite di curvatura della
valvola a lamella:
0,2 mm (0,008 in)Limite de torsion de la
soupape flexible:
0,2 mm (0,008 in)
1P8-9-31-4A 5/12/05 1:18 PM Page 25

2. Install:
9Gasket (reed valve) 1
9Plate (reed valve) 2
9Reed valve assembly 3
9Reed valve spacer 4
NOTE:
Install the reed valve spacer with its chamfered
side ato the right.
4-13
ENGCARBURETOR AND REED VALVE
10 Nm (1.0 m•kg, 7.2 ft•lb)
3. Install:
9Carburetor joint 1
9Bolt (carburetor joint) 2
EC4652F0
Carburetor
1. Install:
9Power jet 1
To carburetor 2.
2. Install:
9O-ring 1
9Solenoid valve 2
To carburetor.
cC
9Before installing the solenoid valve, blow air
on the solenoid valve and its installing loca-
tion on the carburetor in order to remove
any foreign particles such as chips etc.
9Apply the engine oil on the solenoid valve
thread.
1P8-9-31-4A 5/12/05 1:18 PM Page 26

INSPEKTION
Zylinderkopf
1. Entfernen:
9Ölkohleablagerungen
Einen abgerundeten Schaber
1verwenden.
HINWEIS:
Dabei vorsichtig vorgehen, damit das
Gewinde der Zündkerzenbohrung
nicht beschädigt wird. Niemals scharf-
kantige Werkzeuge verwenden, um
ein Zerkratzen des Aluminiums zu
vermeiden.
2. Prüfen:
9Zylinderkopf-Kühlwasserman-
tel
Wasserstein/RostEntfernen.
9Zylinderkopf-Verwerfung
Abweichnung von Spezifikation
Bearbeitung der Oberfläche.
4-21
CULASSE, CYLINDRE ET PISTON
ZYLINDERKOPF, ZYLINDER UND KOLBEN
TESTA CILINDRO, CILINDRO E PISTONEENG
VERIFICATION
Culasse
1. Éliminer:
9Depôts de carbone
Utiliser le grattoir arrondi 1.
N.B.:
Prendre garde à ne pas rayer le filetage
du trou de bougie et les sièges de sou-
pape. Ne pas utiliser d’instrument poin-
tu. Eviter de rayer l’aluminium.
2. Examiner:
9Chemise d’eau de la culasse
Couche de minéraux/rouille
Eliminer.
9Déformation de la culasse
Hors-spécificationRectifier.
IC474000
ISPEZIONE
IC474102
Testa cilindro
1. Eliminare:
9Depositi carboniosi
Usare un raschietto arrotondato
1.
NOTA:
Fare attenzione a evitare di danneggiare
le filettature della candela. Non usare
uno strumento appuntito. Evitare di
graffiare l’alluminio.
2. Ispezionare:
9Camicia d’acqua della testa
cilindro
Crosta di
minerali/RuggineToglierle.
9Svergolamento della testa cilin-
dro
Fuori specificaRispianare e
rifinire la superficie.
3. Ausbauen:
9Kolbenring 1
HINWEIS:
Darauf achten, den Kolben nicht zu
zerkratzen oder den Kolbenring nicht
dadurch zu beschädigen, dass man
ihn mehr als erforderlich dehnt.
3. Déposer:
9Segment 1
N.B.:
Veillez à ne pas rayer le piston et à ne
pas endommager le segment en
l’ouvrant plus que nécessaire.
3. Togliere:
9Fascia elastica 1
NOTA:
Attenzione a non graffiare il pistone o
danneggiare la fascia elastica allargan-
dola più di quanto sia necessario.
Procédure de mesure de la défor-
mation et rectification:
9Poser une règle 1et un calibre
d’épaisseur 2sur la culasse.
9Mesurer la déformation.
9Si la déformation est hors-spécifi-
cation, rectifier la culasse.
9Mettre un morceau de toile émeri
humide de N°400~600 3sur un
marbre et rectifier la culasse 4en
lui faisant faire des “huit”.
N.B.:
Tourner la culasse plusieurs fois
pouréviter d’enlever trop de matière
d’un côté.
Limite de déformation:
0,03 mm (0,0012 in)
Schritte für Messung der Ver-
werfung und Bearbeitung der
Oberfläche:
9Am Zylinderkopf ein Lineal 1
und Einstell-Lehre 2anbringen.
9Die Verwerfungsgrenze messen.
9Wenn die Verwerfung nicht den
erforderlichen Maßen entspricht,
Zylinderkopffläche bearbeiten.
9Ein feuchtes Sandpapier 3
(Feinheit 400~600) auf die Ober-
flächenplatte legen und den
Zylinderkopf 4durch Aus-
führung einer Achterfigur
abschleifen.
HINWEIS:
Um zu vermeiden, dass an einer
Seite zu viel abgeschliffen wird,
den Zylinderkopf mehrmals dre-
hen.
Verwerfungsgrenze:
0,03 mm (0,0012 in)
Passi della misurazione e la
rispianatura e rifinitura della
superficie dello svergolamento:
9Collegare alla testa cilindro un
guardapiano 1e uno spessimetro
2.
9Misurare lo svergolamento.
9Se lo svergolamento è fuori speci-
fica, rispianare e rifinire la super-
ficie della testa cilindro.
9Collocare carta vetrata umida di
grana no. 400~600 3sul piano di
riscontro e rispianare e rifinire la
superficie della testa 4usando
uno schema di carteggiatura a
forma di otto.
NOTA:
Ruotare la testa cilindro diverse
volte per evitare di togliere troppo
materiale da un lato.
Limite di svergolamento:
0,03 mm (0,0012 in)
1P8-9-31-4A 5/12/05 1:19 PM Page 43

4-27
ENGCYLINDER HEAD, CYLINDER AND PISTON
EC475000
ASSEMBLY AND INSTALLATION
EC475193
Power valve
1. Install:
9Power valve 1 1
9Valve holder 2 2
9Bolt (valve holder 2) 3
NOTE:
9Install the power valve 1 with its gouge afac-
ing upside.
9Apply the molybdenum disulfide oil on the
power valve 1.
2. Install:
9Power valve 2 1
9Link rod 2
9Plain washer 3
9Screw (link rod) 4
NOTE:
Install the link rod with the cuts ain its arm
ends fitting over the pins bon the power valves
2.
3. Install:
9Thrust plate 1
9Screw (thrust plate) 2
NOTE:
Be sure to install the thrust plate to the cylinder
before installing the valve shaft.
6 Nm (0.6 m•kg, 4.3 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
1P8-9-31-4A 5/12/05 1:19 PM Page 54

4-28
CYLINDER HEAD, CYLINDER AND PISTONENG
4. Install:
9Spring 1 1
9Link lever 2
9Pulley 3
9Spring 2 4
9Plain washer 5
9Valve shaft 6
NOTE:
9Install the spring 1 to the link lever, and then to
the cylinder.
9Install the spring 1 with its stopper portion a
facing inward.
9Apply the molybdnum disulfide oil on the
grooves in the pulleys.
9Apply the lithium soap base grease on the oil
seal lip.
9Install the valve shaft with its cut baligning
with the thrust plate 7, and then rotate the
valve shaft so that its cut faces upward.
5. Install:
9Valve holder 1 1
9Bolt (link lever) 2
9Bolt (pulley) 3
NOTE:
First tighten the bolt (link lever), and then tighten
the bolts (pulleys).
6. Check:
9Power valve 1 smooth movement
Unsmooth movement Repair or
replace.
4 Nm (0.4 m•kg, 2.9 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
1P8-9-31-4B 4/29/05 3:07 PM Page 2

4-29
CYLINDER HEAD, CYLINDER AND PISTONENG
7. Install:
9O-ring 1
9Side holder 2
9Screw (side holder) 3
9YPVS breather hose 4
NOTE:
9Apply the lithium soap base grease on the O-
rings.
9Install the side holder with its projection a
facing upward.
8. Install:
9Gasket (power valve cover) 1
9Power valve cover 2
9Screw (power valve cover) 3
NOTE:
9Install the gasket with its cut afacing down-
ward and the seal print side toward the power
valve cover.
9Install the power valve cover so that the arrow
mark bfaces upward.
EC475233
Piston ring and piston
1. Install:
9Piston ring 1
NOTE:
9Take care not to scratch the piston or damage
the piston ring.
9Align the piston ring gap with the pin 2.
9After installing the piston ring, check the
smooth movement of it.
2. Install:
9Gasket (cylinder) 1
9Small end bearing 2
9Dowel pin 3
NOTE:
9Apply the engine oil onto the bearing (crank-
shaft and connecting rod) and connecting rod
big end washers.
9Install the gasket with the seal print side toward
the crankcase.
4 Nm (0.4 m•kg, 2.9 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
1P8-9-31-4B 4/29/05 3:07 PM Page 4

4-30
CYLINDER HEAD, CYLINDER AND PISTONENG
EC475383
Cylinder head and cylinder
1. Apply:
9Engine oil
To piston 1piston ring 2and cylinder sur-
face.
2. Install:
9Cylinder 1
cC
Make sure the piston rings are properly
positioned. Install the cylinder with one
hand while compressing the piston rings
with the other hand.
NOTE:
After installing, check the smooth movement of
the piston.
3. Install:
9Nut (cylinder) 1
NOTE:
Tighten the nuts in stage, using a crisscross pat-
tern.
3. Install:
9Piston 1
9Piston pin 2
9Piston pin clip 3
NOTE:
9The arrow aon the piston dome must point to
exhaust side.
9Before installing the piston pin clip, cover the
crankcase with a clean rag to prevent the pis-
ton pin clip from falling into the crankcase cavi-
ty.
cC
Do not allow the clip open ends to meet the
piston pin slot b b
.
42 Nm (4.2 m•kg, 30 ft•lb)
1P8-9-31-4B 4/29/05 3:07 PM Page 6