2006 YAMAHA YZ125LC drain bolt

1-1
GEN
INFO
DESCRIPTION
EC100000
GENERAL INFORMATION
EC110000
DESCRIPTION
1Clutch lever
2“ENGINE STOP” button
3Front brake lever
4Throttle grip
5Radiator cap
6Fuel tank cap
7Kick starter
8Fuel tank
9Radiator
0Coolant drain bolt
qCheck bolt (Transmission oil level)
wRear brake pedal
eValve joint
rFuel cock
tAir cleaner
yDrive chain
uShift pedal
iStarter knob
oFront fork
NOTE:
9The machine you have purchased may differ
slightly from those shown in the following.
9Designs and specifications are subject to
change without notice.
1C3-9-31-1A 4/21/05 10:54 AM Page 2

2-5
SPECMAINTENANCE SPECIFICATIONS
Part to be tightened Thread size Q'tyT ightening torqueNm m•kg ft•lb
Spark plug
M14S×1.25 1 20 2.0 14
Cylinder head (nut) M 8 ×1.25 5 28 2.8 20
(stud) M 8 ×1.25 5 13 1.3 9.4
Cylinder (nut) M 8 ×1.25 4 30 3.0 22
(stud) M10 ×1.25 4 13 1.3 9.4
Power valve:
Cover M 5 ×0.8 4 5 0.5 3.6
Link lever M 4 ×0.7 1 4 0.4 2.9
Holder (power valve) M 5 ×0.8 4 8 0.8 5.8
Push rod M 5 ×0.8 1 5 0.5 3.6
Thrust plate M 5 ×0.8 1 4 0.4 2.9
Governor fork M 4 ×0.7 2 5 0.5 3.6
Housing M 5 ×0.8 3 4 0.4 2.9
Water pump housing cover M 6 ×1.0 4 10 1.0 7.2
Coolant drain bolt M 6 ×1.0 1 10 1.0 7.2
Radiator M 6 ×1.0 6 10 1.0 7.2
Radiator panel M 6 ×1.0 2 10 1.0 7.2
Radiator hose clamp M 6 ×1.0 8 2 0.2 1.4
Air filter element M 6 ×1.0 1 2 0.2 1.4
Carburetor joint M 6 ×1.0 4 10 1.0 7.2
Carburetor joint clamp M 4 ×0.7 1 2 0.2 1.4
Air filter joint clamp M 4 ×0.7 1 2 0.2 1.4
Air filter case M 6 ×1.0 4 8 0.8 5.8
Air filter guide clamp M 5 ×0.8 1 4 0.4 2.9
Read valve M 3 ×0.5 6 1 0.1 0.7
Throttle cable adjust bolt and locknut M 8 ×1.25 1 7 0.7 5.1
Throttle cable M 6 ×0.75 1 4 0.4 2.9
Crankcase M 6 ×1.0 12 14 1.4 10
Crankcase cover (right) M 6 ×1.0 8 10 1.0 7.2
Crankcase cover (left) M 6 ×1.0 4 5 0.5 3.6
Chain cover M 6 ×1.0 2 5 0.5 3.6
Bearing plate cover M 6 ×1.0 4 10 1.0 7.2
Holder M 6 ×1.0 1 10 1.0 7.2
Oil check bolt M 6 ×1.0 1 10 1.0 7.2
Oil drain bolt M10 ×1.25 1 20 2.0 14
Kick starter M 6 ×1.0 1 10 1.0 7.2
Cluch cover M 6 ×1.0 6 10 1.0 7.2
Primary drive gear M 8 ×1.25 1 48 4.8 35
Clutch boss M16 ×1.0 1 80 8.0 58
Clutch spring M 6 ×1.0 5 10 1.0 7.2
Clutch cable adjust bolt and locknut M 6 ×0.75 1 4 0.4 2.9
Drive sprocket M18 ×1.0 1 75 7.5 54
Shift pedal M 6 ×1.0 1 12 1.2 8.7
Bearing plate cover (shift cam) M 6 ×1.0 2 10 1.0 7.2
Shift guide M 6 ×1.0 2 10 1.0 7.2
Stopper lever M 6 ×1.0 1 10 1.0 7.2
Segment M 8 ×1.25 1 30 3.0 22
 
1C3-9-31-2A 4/30/05 2:37 PM Page 6

3-5
INSP
ADJENGINE/COOLANT LEVEL INSPECTION/
COOLANT REPLACEMENT
EC350000
ENGINE
EC351011
COOLANT LEVEL INSPECTION
w
Do not remove the radiator cap 1 1
, drain
bolt and hoses when the engine and radia-
tor are hot. Scalding hot fluid and steam
may be blown out under pressure, which
could cause serious injury.
When the engine has cooled, place a thick
towel over the radiator cap, slowly rotate
the cap counterclockwise to the detent.
This procedure allows any residual pres-
sure to escape. When the hissing sound
has stopped, press down on the cap while
turning counterclockwise and remove it.
cC
Hard water or salt water is harmful to the
engine parts. You may use distilled water,
if you can’t get soft water.
1. Place the machine on a level place, and
hold it in an upright position.
2. Remove:
9Radiator cap
3. Check:
9Coolant level a
Coolant level low Add coolant.
1Radiator
EC353011
COOLANT REPLACEMENT
w
Do not remove the radiator cap when the
engine is hot.
1C3-9-31-3A 4/28/05 2:48 PM Page 18

3-6
INSP
ADJ
COOLANT REPLACEMENT
cC
Take care so that coolant does not splash
on painted surfaces. If it splashes, wash it
away with water.
1. Place a container under the engine.
2. Remove:
9Coolant drain bolt 1
3. Remove:
9Radiator cap
Drain the coolant completely.
4. Clean:
9Cooling system
Thoroughly flush the cooling system with
clean tap water.
5. Install:
9Copper washer
9Coolant drain bolt
6. Fill:
9Radiator
9Engine
To specified level.
Recommended coolant:
High quality ethylene glycol
anti-freeze containing
anti-corrosion for
aluminum engine
Coolant 1 1
and water
(soft water) 2 2
mixing ratio:
50%/50%
Coolant capacity:
0.9 L (0.79 Imp qt, 0.95 US qt)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-31-3A 4/28/05 2:48 PM Page 20

3-14
INSP
ADJ
PILOT AIR SCREW ADJUSTMENT
4. Remove:
9Oil drain bolt 1
9Oil filler cap 2
Drain the transmission oil.
5. Install:
9Aluminum washer
9Oil drain bolt 1
6. Fill:
9Transmission oil
7. Check:
9Oil leakage
8. Check:
9Transmission oil level
9. Install:
9Oil filler cap 2
EC35L002
PILOT AIR SCREW ADJUSTMENT
1. Adjust:
9Pilot air screw 1
Recommended oil:
Yamalube 4 (10W-30) or SAE
10W-30 type SE motor oil
Oil capacity
(periodic oil change):
0.66 L (0.58 Imp qt, 0.69 US qt)
Adjustment steps:
9Screw in the pilot air screw until it is lightly
seated.
9Back out by the specified number of turns.
Pilot air screw:
2-1/4 turns out
20 Nm (2.0 m•kg, 14 ft•lb)
1C3-9-31-3A 4/28/05 2:49 PM Page 36

3-20
FRONT BRAKE PAD INSPECTION AND REPLACEMENT
INSP
ADJ
9Loosen the pad pin 2.
9Remove the caliper 3from the front fork.
9Remove the pad pin and brake pads 4.
9Connect the transparent hose 5to the
bleed screw 6and place the suitable con-
tainer under its end.
9Loosen the bleed screw and push the
caliper piston in.
cC
Do not reuse the drained brake fluid.
9Tighten the bleed screw.
9Install the brake pads 7and pad pin.
NOTE:
9Install the brake pads with their projections
ainto the caliper recesses b.
9Temporarily tighten the pad pin at this point.
9Install the caliper 8and tighten the pad pin
9.
Bleed screw:
6 Nm (0.6 m•kg, 4.3 ft•b)
Bolt (caliper):
23 Nm (2.3 m•kg, 17 ft•lb)
Pad pin:
18 Nm (1.8 m•kg, 13 ft•lb)
1C3-9-31-3B 4/30/05 2:59 PM Page 4

3-22
REAR BRAKE PAD INSPECTION AND REPLACEMENT
INSP
ADJ
9Remove the pad pin 6and brake pads 7.
9Connect the transparent hose 8to the
bleed screw 9and place the suitable con-
tainer under its end.
9Loosen the bleed screw and push the
caliper piston in.
cC
Do not reuse the drained brake fluid.
9Tighten the bleed screw.
9Install the brake pads 0and pad pin q.
NOTE:
9Install the brake pads with their projections
ainto the caliper recesses b.
9Temporarily tighten the pad pin at this point.
9Install the caliper wand rear wheel e.
Refer to “FRONT WHEEL AND REAR
WHEEL” section in the CHAPTER 5.
9Tighten the pad pin r.
9Install the pad pin plug tand protector y.
Bleed screw:
6 Nm (0.6 m•kg, 4.3 ft•lb)
Pad pin:
18 Nm (1.8 m•kg, 13 ft•lb)
Pad pin plug:
3 Nm (0.3 m•kg, 2.2 ft•lb)
Bolt (protector):
7 Nm (0.7 m•kg, 5.1 ft•lb)
3. Inspect:
9Brake fluid level
Refer to “BRAKE FLUID LEVEL
INSPECTION” section.
4. Check:
9Brake pedal operation
A softy or spongy feeling Bleed brake
system.
Refer to “BRAKE SYSTEM AIR BLEEDING”
section.
1C3-9-31-3B 4/30/05 2:59 PM Page 8

4-30
CLUTCH AND PRIMARY DRIVEN GEARENG
Extent of removal Order Part name Q’ty Remarks
CLUTCH PLATE AND
FRICTION PLATE REMOVAL
Preparation for Drain the transmission oil.
Refer to “TRANSMISSION OIL REPLACE-
removalMENT” section in the CHAPTER 3.
Bolt (brake pedal) Shift the brake pedal downward.
Rotor and stator Refer to
“CDI MAGNETO”section.
Clutch cable Disconnect at engine side.
1 Clutch cover 1
2 Screw (clutch spring) 6
3 Clutch spring 6
4 Pressure plate 1
5 Friction plate 8
6 Clutch plate 7
Extent of removal:1Clutch plate and friction plate removal
EC490000
CLUTCH AND PRIMARY DRIVEN GEAREC498000
CLUTCH PLATE AND FRICTION PLATE
1
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-31-4B 4/28/05 2:38 PM Page 26