2006 YAMAHA YZ125LC engine

3-13
INSP
ADJ
TRANSMISSION OIL REPLACEMENT
3. Check:
9Transmission oil level
EC35K002
TRANSMISSION OIL REPLACEMENT
1. Start the engine and warm it up for several
minutes and wait for five minute.
2. Place the machine on a level place and hold
it on upright position by placing the suitable
stand under the engine.
3. Place a suitable container under the engine.
Transmission oil level checking steps:
9Remove the oil check bolt 1.
9Inspect the oil level.
NOTE:
Be sure the machine is positioned straight
up when inspecting the oil level.
w
Never attempt to remove the oil check bolt
just after high speed operation. The heat-
ed oil could spout out, causing danger.
Wait until the oil cools down.
Oil flows out Oil level is correct.
Oil does not flow out Oil level is low.
Add transmission
oil until oil flows
out.
9Inspect the gasket (oil check bolt), replace if
damaged.
9Tighten the oil check bolt.
Recommended oil:
Yamalube 4 (10W-30) or SAE
10W-30 type SE motor oil
Oil check bolt:
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-31-3A 4/28/05 2:48 PM Page 34

3-15
INSP
ADJIDLE SPEED ADJUSTMENT/MUFFLER INSPECTION/
SILENCER FIBER REPLACEMENT
EC35M010
IDLE SPEED ADJUSTMENT
1. Start the engine and thoroughly warm it up.
2. Adjust:
9Idle speed
EC35P030
MUFFLER INSPECTION
1. Inspect:
9O-ring 1
Damage Replace.
NOTE:
Install the O-rings with their depressed afacing
outward.
EC35R050
SILENCER FIBER REPLACEMENT
1. Remove:
9Side cover (right)
9Bolt (silencer) 1
9Silencer 2
9Bolt (fiber) 3
ÅFor USA and CDN
ıExcept for USA and CDN
Adjustment steps:
9Loosen the locknut 1.
9Turn the throttle stop screw 2until the en-
gine runs at the lowest possible speed.
9Tighten the locknut.
To increase idle speed Turn the throttle
stop screw 2 2
in.
To decrease idle speed Turn the throttle
stop screw 2 2
out.
A
B
1C3-9-31-3A 4/28/05 2:49 PM Page 38

3-25
DRIVE CHAIN SLACK ADJUSTMENT
INSP
ADJ
EC36A061
DRIVE CHAIN SLACK ADJUSTMENT
1. Elevate the rear wheel by placing the suit-
able stand under the engine.
2. Check:
9Drive chain slack a
Above the seal guard installation bolt.
Out of specification Adjust
NOTE:
Before checking and/or adjusting, rotate the rear
wheel through several revolutions and check the
slack several times to find the tightest point. Check
and/or adjust chain slack with rear wheel in this
“tight chain” position.
Drive chain slack:
48~58 mm (1.9~2.3 in)
Drive chain lubricant:
SAE 10W-30 motor oil or suitable
chain lubricants
5. Install:
9Drive chain 1
9Joint 2
9Master link clip 3
cC
Be sure to install the master link clip to the
direction as shown.
aTurning direction
6. Lubricate:
9Drive chain
4. Check:
9Drive chain stiffness a
Clean and oil the chain and hold as
illustrated.
StiffReplace drive chain.
1C3-9-31-3B 4/30/05 2:59 PM Page 14

3-26
FRONT FORK INSPECTION
INSP
ADJ
3. Adjust:
9Drive chain slack
EC36C000
FRONT FORK INSPECTION
1. Inspect:
9Front fork smooth action
Operate the front brake and stroke the
front fork.
Unsmooth action/oil leakage Repair or
replace.
Drive chain slack adjustment steps:
9Loosen the axle nut 1and locknuts 2.
9Adjust chain slack by turning the
adjusters 3.
To tighten Turn adjuster 3 3
counter-
clockwise.
To loosen Turn adjuster 3 3
clockwise
and push wheel forward.
9Turn each adjuster exactly the same amount
to maintain correct axle alignment. (There are
marks aon each side of chain puller align-
ment.)
NOTE:
Turn the adjuster so that the chain is in line
with the sprocket, as viewed from the rear.
cC
Too small chain slack will overload the
engine and other vital parts; keep the
slack within the specified limits.
9Tighten the axle nut while pushing down the
drive chain.
9Tighten the locknuts.
Axle nut:
125 Nm (12.5 m•kg, 90 ft•lb)
Locknut:
16 Nm (1.6 m•kg, 11 ft•lb)
1C3-9-31-3B 4/30/05 2:59 PM Page 16

3-27
FRONT FORK OIL SEAL AND DUST SEAL CLEANING/
FRONT FORK INTERNAL PRESSURE RELIEVING/
FRONT FORK REBOUND DAMPING FORCE ADJUSTMENTINSP
ADJ
EC36D001
FRONT FORK OIL SEAL AND DUST SEAL
CLEANING
1. Remove:
9Protector
9Dust seal 1
NOTE:
Use a thin screw driver, and be careful not to
damage the inner fork tube and dust seal.
2. Clean:
9Dust seal a
9Oil seal b
NOTE:
9Clean the dust seal and oil seal after every run.
9Apply the lithium soap base grease on the in-
ner tube.
EC36H002
FRONT FORK REBOUND DAMPING FORCE
ADJUSTMENT
1. Adjust:
9Rebound damping force
By turning the adjuster 1.
Stiffer a a
Increase the rebound damping
force. (Turn the adjuster 1 1
in.)
Softer b b
Decrease the rebound
damping force. (Turn the
adjuster 1 1
out.)
EC36f000
FRONT FORK INTERNAL PRESSURE
RELIEVING
NOTE:
If the front fork initial movement feels stiff during
a run, relieve the front fork internal pressure.
1. Elevate the front wheel by placing a suitable
stand under the engine.
2. Remove the air bleed screw 1and release
the internal pressure from the front fork.
3. Install:
9Air bleed screw
1 Nm (0.1 m•kg, 0.7 ft•lb)
1C3-9-31-3B 4/30/05 2:59 PM Page 18

NOTE:
9Be sure to remove all dirt and mud from around
the locknut and adjuster before
adjustment.
9The length of the spring (installed) changes 1.5
mm (0.06 in) per turn of the adjuster.
9The I.D. color bis marked at the end of the
spring.
cC
Never attempt to turn the adjuster beyond
the maximum or minimum setting.
3-30
REAR SHOCK ABSORBER SPRING PRELOAD
ADJUSTMENTINSP
ADJ
EC36M014
REAR SHOCK ABSORBER SPRING
PRELOAD ADJUSTMENT
1. Elevate the rear wheel by placing the suit-
able stand under the engine.
2. Remove:
9Rear frame
3. Loosen:
9Locknut 1
4. Adjust:
9Spring preload
By turning the adjuster 2.
Stiffer Increase the spring preload.
(Turn the adjuster 2 2
in.)
Softer Decrease the spring pre-
load. (Turn the adjuster 2 2
out.)
Extent of adjustment
245.5~263.5 mm
(9.67~10.37 in)
251.5~269.5 mm
(9.90~10.61 in)
243.0~261.0 mm
(9.57~10.28 in)
Spring length (installed) a a
:
Standard length
One I.D. paint mark
257 mm (10.12 in)
*256 mm (10.08 in)
Two I.D. paint marks
263 mm (10.35 in)
*262 mm (10.31 in)
Three I.D. paint marks
254.5 mm (10.02 in)
*253.5 mm (9.98 in)
*For EUROPE
1C3-9-31-3B 4/30/05 2:59 PM Page 24

3-35
STEERING HEAD INSPECTION AND ADJUSTMENT
INSP
ADJ
2. Inspect:
9Bearing free play
Exist play Replace.
EC36U070
STEERING HEAD INSPECTION AND
ADJUSTMENT
1. Elevate the front wheel by placing a suitable
stand under the engine.
2. Check:
9Steering shaft
Grasp the bottom of the forks and gently
rock the fork assembly back and forth.
Free play Adjust steering head.
3. Check:
9Steering smooth action
Turn the handlebar lock to lock.
Unsmooth action Adjust steering ring
nut.
4. Adjust:
9Steering ring nut
Steering ring nut adjustment steps:
9Remove the number plate.
9Remove the handlebar and handle crown.
9Loosen the ring nut 1using the ring nut
wrench 2.
9Tighten the ring nut 3using ring nut wrench
4.
NOTE:
9Apply the lithium soap base grease on the
thread of the steering shaft.
9Set the torque wrench to the ring nut wrench
so that they form a right angle.
Ring nut wrench:
YU-33975/90890-01403
1C3-9-31-3B 4/30/05 3:00 PM Page 34

3-38
ELECTRICAL/SPARK PLUG INSPECTION
INSP
ADJ
EC370000
ELECTRICAL
EC371001
SPARK PLUG INSPECTION
1. Remove:
9Spark plug
2. Inspect:
9Electrode 1
Wear/Damage Replace.
9Insulator color 2
Normal condition is a medium to light tan
color.
Distinctly different color Check the
engine condition.
NOTE:
When the engine runs for many hours at low
speeds, the spark plug insulator will become
sooty, even if the engine and carburetor are in
good operating condition.
3. Measure:
9Plug gap a
Use a wire gauge or thickness gauge.
Out of specification Regap.
4. Clean the plug with a spark plug cleaner if
necessary.
5. Tighten:
9Spark plug
NOTE:
9Before installing a spark plug, clean the
gasket surface and plug surface.
9Finger-tighten athe spark plug before torquing
to specification b.
Spark plug gap:
0.6~0.7 mm (0.024~0.028 in)
Standard spark plug:
BR9EVX/NGK (resistance type)
20 Nm (2.0 m•kg, 14 ft•lb)
1C3-9-31-3B 4/30/05 3:00 PM Page 40