2006 YAMAHA YFM700R brake

5-1
EBU01130
PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Front brake9Check operation, free play, fluid level and fluid leakage. 5-7–5-11
9Fill with DOT 4 brake fluid if necessary. 8-71–8-81
Rear brake9Check operation, free play, fluid level and fluid leakage. 5-7–5-11
9Fill with DOT 4 brake fluid if necessary. 8-71–8-81
Clutch9Check operation, condition and lever free play. 8-89
Parking brake9Check operation, condition and cable length. 8-83–8-85
Fuel 9Check fuel level.
9Fill with fuel if necessary.5-13–5-15
Engine oil9Check oil level.
9Fill with oil if necessary.5-17, 8-21
Coolant reservoir 9Check coolant level in reservoir.
9Fill with coolant if necessary.5-19, 8-37–8-47
Drive chain9Check chain slack and condition.
9Adjust if necessary.5-23, 8-91–8-99
Throttle9Check for proper throttle cable operation and free play. 5-23, 8-69
Wheels and tires9Check tire pressure, wear and damage. 5-25–5-31, 8-111–8-113
Fittings and fasteners9Check all fittings and fasteners. 5-31
Lights and switches9Check for proper operation. 5-31, 8-125–8-131
1S3-9-60 5-6 6/7/05 10:22 AM Page 5-1

5-7
EBU11670
Front and rear brakes
Brake lever and brake pedal
8Check that there is no free play in the brake
lever. If there is free play, have a Yamaha
dealer inspect the brake system.
8Check for correct brake pedal height. (See
page 8-81.) If the pedal height is incorrect,
have a Yamaha dealer adjust it.
8Check the operation of the brake lever and
brake pedal. They should move smoothly and
there should be a firm feeling when the
brakes are applied. If not, have a Yamaha
dealer inspect the brake system.
Brake fluid level
Check the brake fluid level. Add fluid if neces-
sary. (See pages 8-73–8-75.)
Recommended brake fluid: DOT 4
1S3-9-60 5-6 6/7/05 10:22 AM Page 5-7

5-9
Brake fluid leakage
Check to see if any brake fluid is leaking out of
the pipe joints or brake fluid reservoirs. Apply
the brakes firmly for one minute. If there is any
leakage, have a Yamaha dealer inspect the
brake system.
Brake operation
Test the brakes at slow speed after starting out
to make sure they are working properly. If the
brakes do not provide proper braking perfor-
mance, inspect the brake pads for wear. (See
page 8-71.)
1S3-9-60 5-6 6/7/05 10:22 AM Page 5-9

5-11
w
Always check the brakes at the start of every
ride. Do not ride the ATV if you find any
problem with the brakes or you could lose
braking ability, which could lead to an acci-
dent. If a problem cannot be corrected by the
adjustment procedures provided in this man-
ual, have a Yamaha dealer check for the
cause.
1S3-9-60 5-6 6/7/05 10:22 AM Page 5-11

5-31
EBU01600
Tire wear limit
When the tire groove decreases to 3 mm (0.12
in) due to wear, replace the tire.
EBU11620
Fittings and fasteners
Always check the tightness of chassis fittings
and fasteners before a ride. Take the machine
to a Yamaha dealer or refer to the Service
Manual for correct tightening torque.
EBU10030
Lights
Check the headlights and tail/brake light to
make sure they are in working condition. Repair
as necessary for proper operation.
EBU11700
Switches
Check the operation of all switches. Have a
Yamaha dealer repair as necessary for proper
operation.
a
1S3-9-60 5-6 6/7/05 10:22 AM Page 5-31

6-3
EBU15901
Starting the engine
w
Always make sure all control cables work
smoothly before you begin riding in cold
weather. If the control cables are frozen or
do not work smoothly, you could be unable
to control the ATV, which could lead to an
accident or collision.
1. Set the parking brake.
2. Turn the main switch to “ON” and the
engine stop switch to “RUN”.
cC
The engine trouble warning light and the fuel
level warning light should come on, and then
go off.
If a warning light does not go off, see page
4-7 for the corresponding warning light cir-
cuit check.
3. Shift the transmission into neutral.
1S3-9-60 5-6 6/7/05 10:22 AM Page 6-3

6-9
2
1
1. Reverse knob “REV”
2. Shift pedal
1. Bouton de marche arrière “REV”
2. Pédale de sélection
1. Botón de marcha atrás “REV”
2. Pedal del cambio
EBU12102
Reverse knob operation and reverse driving
cC
Before shifting, stop the machine and return
the throttle lever to its closed position, other-
wise the transmission may be damaged.
1. Bring the machine to a complete stop,
return the throttle lever to the closed posi-
tion, apply the clutch lever, and then shift
the transmission into first gear.
2. While applying the brake pedal, turn the
reverse knob clockwise with your right
hand.
3. Apply the clutch lever and shift the trans-
mission into reverse by pressing down on
the shift pedal.
NOTE:
When in reverse, the reverse indicator light
should be on. If the light does not come on, ask
a Yamaha dealer to inspect the machine.
1S3-9-60 5-6 6/7/05 10:22 AM Page 6-9

6-11
4. Check behind you for people or obstacles,
and then release the brake pedal.
5. Open the throttle lever gradually, and at
the same time, release the clutch lever
slowly, and continue to watch to the rear
while backing.
w
Improper operation in reverse could make
you hit an obstacle or person behind you,
resulting in serious injury. When you shift
into reverse, make sure there are no obsta-
cles or people behind you. When it is safe to
proceed, go slowly.
1S3-9-60 5-6 6/7/05 10:22 AM Page 6-11