2006 YAMAHA XMAX 250 light

Pushing the “SET” button when in the
tripmeter mode switches the display
between the different tripmeter func-
tions in the following order:
Distance
Time Average speed
Distance
If the fuel level warning light comes on
(See page 3-3.), the display will auto-
matically change to the fuel reserve
tripmeter mode “Trip/fuel” and start
counting the distance traveled from
that point. In that case, pushing the
“SET” button switches the display
between the various tripmeter and
odometer modes in the following
order:
Trip/Fuel
Trip 1 Trip 2 Total
Trip/fuelTo reset a tripmeter, select it by pus-
hing the “MODE” button, and then
push the “SET” button for at least one
second. If you do not reset the fuel
reserve tripmeter manually, it will
reset itself automatically and the dis-
play will return to the prior mode after
refueling and traveling 5 km.
Clock mode
To set the clock:
1. When the display is in the “Total”
mode, push the “SET” button for
at least two seconds.
2. When the hour digits start flas-
hing, push the “SET” button to
set the hours.3. Push the “MODE” button, and
the minute digits will start flas-
hing.
4. Push the “SET” button to set the
minutes.
5. Push the “MODE” button and
then release it to start the clock.
The display will return to the
“Total” mode.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-7
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-7

EAU12344
Handlebar switches
1. Dimmer switch “jk”
2. Pass switch "PASSING"
3. Turn signal switch “cd”
4. Horn switch “a”
1. Starting switch “g”
2. Hazard switch“”
EAUS1300
Pass switch “PASSING”
Press this switch to flash the head-
light.
EAUS1020
Dimmer switch “j/k”
Set this switch to “
j” for the high
beam and to “
k” for the low beam.
With the headlight on low beam,
press this switch downwards to flash
the headlight.
EAU12460
Turn signal switch “c/d”
To signal a right-hand turn, push this
switch to “
d”. To signal a left-hand
turn, push this switch to “
c”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “a”
Press this switch to sound the horn.
EAU12720
Start switch “g”
With the sidestand up, push this
switch while applying the front or rearbrake to crank the engine with the
starter.
ECA10050
CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
EAUM1990
Hazard switch “ ”, “h”
With the key in the “ON” position, set
this switch to “ ” to turn on the
hazard lighting (simultaneous flashing
of all turn signal lights). To turn off the
hazard lighting, set this switch to “h”
and, then turn the key to “OFF”.
NOTE:
Even if the key is turned from “ON” to
“OFF” with the hazard lighting on, the
hazard lighting will continue to flash
regardless of the hazard switch posi-
tion. To cancel the hazard lighting, the
key must be turned to “ON” and the
hazard switch must be set to the “h”
position.
12
1
2
3
4
3
INSTRUMENT AND CONTROL FUNCTIONS
3-9
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-9

The hazard lighting is used in case of
an emergency or to warn other drivers
when your scooter is stopped where
it might be a traffic hazard.
ECA10060
CAUTION:
Do not use the hazard light for an
extended length of time, otherwise
the battery may discharge.
EAU12900
Front brake lever
1. Front brake lever
The front brake lever is located on the
right handlebar grip. To apply the
front brake, pull this lever toward the
handlebar grip.
EAU12950
Rear brake lever
1. Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the hand-
lebar grip.
11
3
INSTRUMENT AND CONTROL FUNCTIONS
3-10
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-10

EAU15361
Ignition circuit cut-off
system
The ignition circuit cut-off system
(comprising the sidestand switch and
brake light switches) has the following
functions.
It prevents starting when the
sidestand is up, but neither brake
is applied.
It prevents starting when either
brake is applied, but the sides-
tand is still down.
It cuts the running engine when
the sidestand is moved down.
Periodically check the operation of
the ignition circuit cut-off system
according to the following procedure.
EWA10260
s s
WARNING
The vehicle must be placed on
the centerstand during this ins-
pection.
If a malfunction is noted, have
a Yamaha dealer check the
system before riding.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-17
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 3-17

4
PRE-OPERATION CHECKS
4-3
ITEM CHECKS PAGE
Brake levers• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.6-20
Centerstand, sidestand• Make sure that operation is smooth.
• Lubricate pivots if necessary.6-21
Chassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.—
Instruments, lights, signals • Check operation.
and switches• Correct if necessary.—
• Check operation of ignition circuit cut-off system.
Sidestand switch• If system is defective, have Yamaha dealer check vehicle. 3-16
• If system is defective, have Yamaha dealer check vehicle.
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 4-3

areas and cross them with cau-
tion.
Keep in mind that braking on a
wet road is much more difficult.
Ride slowly down a hill, as bra-
king downhill can be very diffi-
cult.
EAU16820
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the follo-
wing tips to reduce fuel consumption:
Avoid high engine speeds during
acceleration.
Avoid high engine speeds with no
load on the engine.
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at
traffic lights or at railroad cros-
sings).
EAU16841
Engine break-in
There is never a more important
period in the life of your engine than
the period between 0 and 1600 km
(1000 mi). For this reason, you should
read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts
in the engine wear and polish them-
selves to the correct operating clea-
rances. During this period, prolonged
full-throttle operation or any condition
that might result in engine overhea-
ting must be avoided.
EAUM2010
0 ~ 1000 km (0 ~ 600 mi)
Avoid prolonged operation above 1/3
throttle.
1000 ~ 1600 km (600 ~ 1000 mi)
Avoid prolonged operation above 1/2
throttle.
ECA11660
CAUTION:
After 1000 km (600 mi) of operation,
be sure to replace the engine oil
and final transmission oil.
5
OPERATION AND IMPORTANT RIDING POINTS
5-3
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 38

6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
8*Brake hose•Check for cracks or damage.√√√√ √•Replace. Every 4 years
9*Wheels•Check runout and for damage.√√√√
•Check tread depth and for damage.
10 * Tires•Replace if necessary.
•Check air pressure.
•Correct if necessary.√√√√ √
11 *Wheel bearings•Check bearing for looseness or damage.√√√√
12 *Steering bearings•Check bearing play and steering for roughness.√√ √ √√•Lubricate with lithium-soap-based grease. Every 20000 km
13 *Chassis fasteners•Make sure that all nuts, bolts and screws are properly
tightened.√√√√ √
14Sidestand, centerstand•Check operation.
•Lubricate.√√√√ √
15 *Sidestand switch•Check operation.√√ √ √√ √
16 *Front fork•Check operation and for oil leakage.√√√√
17 *Shock absorber
assemblies•Check operation and shock absorbers for oil leakage.√√√√
18 *Carburetor•Adjust engine idling speed.√√ √ √√ √
•Change. (See page 6-8.)√When the oil change indicator light comes
19Engine oilon (every 3000 km)
•Check oil level and vehicle for oil leakage. Every 3000 km√
20 *Cooling system•Check coolant level and vehicle for coolant leakage.√√√√ √
•Change. Every 3 years
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 43

6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
21Final transmission oil•Check vehicle for oil leakage.√√ √•Change.√√√
22 *V-belt•Replace. Every 20000 km
23 *Front and rear brake
switches•Check operation.√√ √ √√ √
24Moving parts and cables•Lubricate.√√√√ √
Throttle grip housing •Check operation and free play.
25 * •Adjust the throttle cable free play if necessary.
and cable
•Lubricate the throttle grip housing and cable.√√√√ √
26 *Mufflers and exhaust
pipes•Check the screw clamps for looseness.√√ √ √√ √
27 *Lights, signals •Check operation.
and switches•Adjust headlight beam.√√ √ √√ √
EAU18660
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder and caliper, and change the bra-
ke fluid.
• Replace the brake hoses every four years and if cracked or damaged.
1C0-F8199-E2.qxd 06/03/2006 13:08 Página 44