2006 YAMAHA VX CRUISER engine overheat

2-18
E
EJU20731
Multifunction meter
This meter contains the following func-
tions for help and convenience in operating
the watercraft.
1
Tachometer
2
Speedometer
3
Hour meter/Voltmeter
4
Fuel meter
5
“L-MODE” indicator light (for VX110 Deluxe)
6
Warning light
7
Fuel warning indicator
8
Engine overheat warning indicator
9
Oil pressure warning indicator
0
Check engine warning indicator
A
Select button
B
“SECURITY” indicator light (for VX110 Deluxe)
CAUTION:@ Do not run the engine for more than
15 seconds when checking the operation
of the meter on land. The engine could
overheat.
@
NOTE:@
When the engine is started, all displays
light up for 2 seconds and then the meter
starts to operate normally.

The current display will continue to oper-
ate for 25 seconds after the engine stops.
@
E_F1K-70.book Page 18 Thursday, October 20, 2005 1:30 PM

2-22
E
EJU21183
Engine overheat warning indicator
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the warn-
ing light and the overheat warning indicator
blink, and then come on. The buzzer also
begins to sound intermittently, and then it
sounds continuously. After the light and indi-
cator start to blink and the buzzer sounds,
the engine speed is limited to help prevent
damage.
If this occurs, immediately reduce the
engine speed, return to shore, and then
check for water discharge at the port (left)
cooling water pilot outlet. If there is no dis-
charge of water, check the intake grate and
impeller for clogging.
WARNING@ Before attempting to remove weeds or
debris from the intake grate or impeller,
shut the engine off and remove the clip
from the engine shut-off switch. Severe
injury or death could result from coming
in contact with the rotating parts of the
jet pump.
@
CAUTION:@ If you cannot locate and correct the
cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe
engine damage.
@
NOTE:@ Press the select button 1 on the multifunc-
tion meter to stop the buzzer.
@
E_F1K-70.book Page 22 Thursday, October 20, 2005 1:30 PM

3-13
E
EJU10580
Jet unit
Carefully check the jet intake for weeds,
debris, or anything else that might restrict
the intake of water. If the intake is clogged,
cavitation could occur, reducing jet thrust,
and possibly damaging the jet pump.
In some cases, the engine may overheat
because of lack of cooling water, and dam-
age to the engine could result. Engine cool-
ing water is fed to the engine by the jet
pump. (See page 5-3 for jet intake cleaning
procedures.)
WARNING@
Keep away from intake grate while
engine is on. Items such as long hair,
loose clothing, or PFD straps can
become entangled in moving parts
resulting in severe injury or drowning.

Stop the engine and remove the clip
from the engine shut-off switch before
removing any debris or weeds, which
may have collected around the jet
intake.
@
EJU10590
Engine shut-off cord (lanyard)
Check that the engine shut-off cord is not
frayed or broken. If the cord is damaged,
replace it; never try to repair it or tie it
together.
E_F1K-70.book Page 13 Thursday, October 20, 2005 1:30 PM

3-14
E
EJU18352
Switches
CAUTION:@ Do not run the engine of the watercraft
for more than 15 seconds on land with-
out supplying water, otherwise the
engine may overheat.
@
Check the start switch, the engine stop
switch, and the engine shut-off switch for
proper operation.
Push the start switch 1 to start the
engine. As soon as the engine starts run-
ning, push the engine stop switch 2 to ver-
ify that the engine stops immediately.
Restart the engine, and then pull the engine
shut-off cord 5 to remove the clip 4 from
the engine shut-off switch 3 to verify that
the engine stops immediately. (See pages
2-9 to 2-10 for information on proper opera-
tion of the start switch, the engine stop
switch, and the engine shut-off switch.)
EJU13201
Cooling water pilot outlet
Check that water comes out from the pilot
outlet while the engine is running and the
watercraft is in the water. (See page 2-11 for
more information.)
EJU12460
Multifunction meter
Check the operation of the multifunction
meter. (See pages 2-18 to 2-23 for operation
of the meter.)
E_F1K-70.book Page 14 Thursday, October 20, 2005 1:30 PM

3-34
E
EJU10841
Post-operation checks
Always perform the following post-opera-
tion checks after operating the watercraft.
1. Remove the watercraft from the water.
2. Wash down the hull, handlebars, and jet
unit with fresh water.
3. Remove the seat and check the engine
compartment for water. To drain excess
water, remove the stern drain plugs, and
then raise the bow of the watercraft
enough to allow water in the bilge to
drain out.
NOTE:@ This watercraft is equipped with an auto-
matic bilge-draining system that removes
water from the engine compartment while
you are underway. However, some residual
water will remain.
@
4. Put the watercraft in a horizontal posi-
tion.
5. Flush the cooling system to prevent it
from clogging with salt, sand, or dirt.
(See page 4-1 for flushing procedures.)
6. Drain residual water from the exhaust
system by alternately squeezing and
releasing the throttle lever for 10 to
15 seconds while the engine is running.
CAUTION:@ Do not run the engine for more than
15 seconds on land. The engine could
overheat.
@
E_F1K-70.book Page 34 Thursday, October 20, 2005 1:30 PM

4-1
E
EJU18121
Storage
WARNING@ Always place the watercraft upright in a
horizontal position when storing it, oth-
erwise fuel could leak out into the engine
or engine compartment, which could
result in a fire hazard.
@
Storage for prolonged periods of time,
such as winter storage, requires preventa-
tive maintenance to ensure against deterio-
ration. It is advisable to have the watercraft
serviced by a Yamaha dealer prior to stor-
age. However, the following procedures can
be performed by the owner.
EJU21261
Flushing the cooling system
Flushing the cooling system is essential
to prevent the cooling system from being
clogged with salt, sand, or dirt.
CAUTION:@
Do not supply water to the cooling
water passages when the engine is not
running. The water could flow back
through the muffler into the crankcase
causing severe engine damage.

Do not run the engine of the watercraft
for more than 15 seconds without sup-
plying water, otherwise the engine may
overheat.
@
E_F1K-70.book Page 1 Thursday, October 20, 2005 1:30 PM

4-3
E
EJU21270
Lubrication
WARNING@ Do not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance or
propellants could catch fire.
@
1. Remove the seat. (See page 2-5 for seat
removal and installation procedures.)
2. Loosen the clamp screw 1 and discon-
nect the air intake duct 2.
3. Spray a rust inhibitor into the intake
opening 3 for 3 seconds.
4. Connect the air intake duct and tighten
the clamp screw.
5. Start the engine in a well-ventilated area
and let it run at idle for 15 seconds.
CAUTION:@ Do not run the engine for more than
15 seconds. The engine could overheat.
@
6. Lubricate all cables such as the throttle
and steering cables.
NOTE:@ Use a suitable marine grease applicator to
pressure lubricate the cables and purge out
any moisture between the inner and outer
cables.
@
7. Lubricate the areas of the watercraft
specified under Lubrication points on
page 4-18.
E_F1K-70.book Page 3 Thursday, October 20, 2005 1:30 PM

5-3
E
EJU11180
Emergency procedures
EJU21602
Cleaning the jet intake and
impeller
If weeds or debris get caught in the intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine
speed rises. If this condition is allowed to
continue, the engine will overheat and may
seize. If there is any sign that the jet intake
or impeller is clogged with weeds or debris,
return to shore and check the intake and
impeller. Always stop the engine before
beaching the watercraft.
WARNING@ Before attempting to remove weeds or
debris from the jet intake or impeller
area, shut the engine off and remove the
clip from the engine shut-off switch.
Severe injury or death could result from
coming in contact with the rotating parts
of the jet pump.
@
CAUTION:@ If weeds or debris get caught in the
intake, do not operate the watercraft
above trolling speed until they have been
removed.
@
1. Turn the watercraft on its side as shown.
CAUTION:@
Place a suitable clean cloth or carpet-
ing underneath the watercraft to pro-
tect it from abrasions and scratches.

Always turn the watercraft over onto
its port (left) side.

When turning the watercraft on its
side, support the bow so the handle-
bars cannot be bent or damaged.
@
E_F1K-70.book Page 3 Thursday, October 20, 2005 1:30 PM