2006 YAMAHA VERSITY 300 tow

INSTRUMENT AND CONTROL FUNCTIONS
3-3
3
EAUM1470
Fuel gauge The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the remaining fuel in
the tank reaches approximately 1.9 L
(0.50 US gal) (0.42 Imp.gal), the fuel
level warning light will come on and the
multi-function display will automatically
change to the “Trip/fuel” mode. (See
page 3-4.) If this occurs, refuel as soon
as possible.NOTE:Do not allow the fuel tank to empty itselfcompletely.
EAUM1101
Battery voltage/coolant
temperature gauge When the key is turned to “”, this
gauge indicates the battery voltage lev-
el before the engine was stopped.NOTE:If the needle drops to the “9V” (low)
mark, have a Yamaha dealer check thebattery.
When the key is turned to “”, this
gauge indicates the coolant tempera-
ture. If the needle reaches the red
zone, stop the scooter and allow the
engine to cool. (See page 6-31.)
CAUTION:
ECA10020
Do not operate the engine if it isoverheated.
1. Fuel gauge
2. Fuel level warning light
1
2
ZAUM0403
1. High level
2. Low level
1
2
ZAUM0579
1. Red zone
1
ZAUM0580

INSTRUMENT AND CONTROL FUNCTIONS
3-8
3 position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12500
Horn switch “”
Press this switch to sound the horn.
EAU12660
Engine stop switch “/”
Set this switch to “” before starting
the engine. Set this switch to “” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12720
Start switch “”
With the sidestand up, push this switch
while applying the front or rear brake to
crank the engine with the starter.CAUTION:
ECA10050
See page 5-1 for starting instruc-tions prior to starting the engine.
EAUM1990
Hazard switch “”, “”
With the key in the “” position, set
this switch to “” to turn on the hazard
lighting (simultaneous flashing of all
turn signal lights). To turn off the hazard
lighting, set this switch to “” and, then
turn the key to “”.NOTE:Even if the key is turned from “” to
“” with the hazard lighting on, the
hazard lighting will continue to flash re-
gardless of the hazard switch position.
To cancel the hazard lighting, the key
must be turned to “” and the hazardswitch must be set to the “” position.
The hazard lighting is used in case of
an emergency or to warn other drivers
when your scooter is stopped where it
might be a traffic hazard.CAUTION:
ECA10060
Do not use the hazard light for an ex-
tended length of time, otherwise thebattery may discharge.
EAU12900
Front brake lever The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handle-
bar grip.1. Front brake lever
1
ZAUM0084

INSTRUMENT AND CONTROL FUNCTIONS
3-9
3
EAU12950
Rear brake lever The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handle-
bar grip.
EAU13140
Fuel tank cap To remove the fuel tank cap
1. Open the seat. (See page 3-11.)
2. Insert the key into the lock and turn
it 1/4 turn clockwise. The lock will
be released and the fuel tank cap
can be removed.
To install the fuel tank cap
1. Insert the fuel tank cap into the
tank opening with the marks on the
cap and tank aligned.
2. Turn the key counterclockwise to
the original position, and then re-
move it.
3. Close the seat.
NOTE:The fuel tank cap cannot be installed
unless the key is in the lock. In addition,
the key cannot be removed if the cap isnot properly installed and locked.
WARNING
EWA10120
Make sure that the fuel tank cap is
properly closed and locked beforeriding.
1. Rear brake lever
1
ZAUM0085
1. Fuel tank cap
1
ZAUM0409

OPERATION AND IMPORTANT RIDING POINTS
5-2
5
EAU16760
Starting off NOTE:Before starting off, allow the engine towarm up.
1. While pulling the rear brake lever
with your left hand and holding the
grab bar with your right hand, push
the scooter off the centerstand.
2. Sit astride the seat, and then ad-
just the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off.
5. Switch the turn signal off.
EAU16780
Acceleration and deceleration The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
(a). To reduce the speed, turn the throt-
tle grip in direction (b).
EAU16791
Braking 1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually in-
creasing the pressure.
WARNING
EWA10300


Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.


Railroad crossings, streetcar
rails, iron plates on road con-
struction sites, and manhole
covers become extremely slip-
pery when wet. Therefore, slow
down when approaching such
areas and cross them with cau-
tion.
1. Grab bar
1
ZAUM0419
(b)
(a)
ZAUM0199
PUSH
ZAUM0472

PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
6 Engine overheating
WARNING
EWA10400


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissingsound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
NOTE:If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See NOTE.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.