2006 YAMAHA TTR50 drain bolt

SPEC
2 - 10
Part to be tightened Thread size Q
’ty Tightening torque
Remarks
Nm m ·kg ft ·lb
Cylinder head nut M8 × 1.25 4 22 2.2 16
Cylinder head bolt M6 × 1.0 2 10 1.0 7.2
Spark plug M10 × 1.0 1 13 1.3 9.4
Camshaft sprocket cover bolt M6 × 1.0 2 10 1.0 7.2
Tappet cover M45 × 1.5 2 18 1.8 13
Exhaust pipe stud bolt M6 × 1.0 2 7 0.7 5.1
Rotor nut M12 × 1.25 1 48 4.8 35
Timing chain guide stopper M6 × 1.0 2 10 1.0 7.2
LT
Valve clearance adjust screw locknut M5 × 0.5 2 7 0.7 5.1
Camshaft sprocket M8 × 1.25 1 26 2.6 19
Camshaft bearing retainer M6 × 1.0 1 10 1.0 7.2
LT
Timing chain tensioner cap bolt M8 × 1.25 1 8 0.8 5.8
Timing chain tensioner M6 × 1.0 2 10 1.0 7.2
Oil pump assembly M6 × 1.0 2 7 0.7 5.1
LT
Engine oil drain bolt M12 × 1.5 1 20 2.0 14
Intake manifold (cylinder head side) M6 × 1.0 2 7 0.7 5.1
Intake manifold (carburetor side) M6 × 1.0 2 7 0.7 5.1
Carburetor heater M8 × 1.25 1 3 0.3 2.2
Clamp (air filter joint) M4 × 0.7 1 2 0.2 1.4
Exhaust pipe M6 × 1.0 2 7 0.7 5.1
Muffler M8 × 1.25 1 38 3.8 27
Muffler cover M6 × 1.0 4 7 0.7 5.1
Spark arrester M6 × 1.0 3 10 1.0 7.2
Crankcase M6 × 1.0 10 10 1.0 7.2
Crankcase cover (left) M6 × 1.0 8 10 1.0 7.2
Drive sprocket cover M6 × 1.0 2 7 0.7 5.1
Timing plug M14 × 1.5 1 7 0.7 5.1
Crankshaft end cover M32 × 1.5 1 7 0.7 5.1
Crankcase cover (right) M6 × 1.0 9 10 1.0 7.2
Clutch adjuster locknut M8 × 1.25 1 6 0.6 4.3
Cylinder head stud bolt M8 × 1.25 4 13 1.3 9.4
Starter clutch and rotor M6 × 1.0 3 14 1.4 10 Stake
Clutch housing nut M14 × 1.0 1 70 7.0 50
Pressure plate M5 × 0.8 3 5 0.5 3.6
Primary driven gear M14 × 1.0 1 70 7.0 50
Stopper bolt M8 × 1.25 1 23 2.3 17
LT
Shift pedal M6 × 1.0 1 10 1.0 7.2
Pickup coil M6 × 1.0 2 10 1.0 7.2
LT
Stator assembly M6 × 1.0 3 10 1.0 7.2LT
Neutral switch M10 × 1.25 1 18 1.8 13
MAINTENANCE SPECIFICATIONS

3 - 9
INSPADJENGINE OIL LEVEL INSPECTION/
ENGINE OIL REPLACEMENT
5. Install:
Oil filler cap
6. Start the engine and let it warm up for sev-
eral minutes.
7. Turn off the engine and inspect the oil level once again.
NOTE:
Wait a few minutes until the oil settles before
inspecting the oil level.
ENGINE OIL REPLACEMENT
1. Start the engine and warm it up for severalminutes, and then turn off the engine and
wait for five minutes.
2. Place the machine on a level place and hold it on upright position by placing the
suitable stand under the engine.
3. Place a suitable container under the engine.
4. Remove:
Oil filler cap 1
 Drain bolt (with gasket) 2
Drain the crankcase of its oil.
5. Install: Gasket
 Drain bolt
6. Fill: Crankcase
7. Install: Oil filler cap
8. Inspect: Engine (for oil leaks)
 Oil level
Refer to “ENGINE OIL LEVEL INSPEC-
TION ” section.
Oil quantity:
Periodic oil change: 0.8 L (0.70 Imp qt, 0.85 US qt)
1
2
New
T R..20 Nm (2.0 m · kg, 14 ft · lb)

4 - 48
ENGENGINE REMOVAL
(4)
NewNew
LS
T R..30 Nm (3.0 m • kg, 22 ft • Ib)
T R..30 Nm (3.0 m •
kg, 22 ft • Ib)
T R..30 Nm (3.0 m •
kg, 22 ft • Ib)
T R..30 Nm (3.0 m •
kg, 22 ft • Ib)
T R..48 Nm (4.8 m •
kg, 35 ft • Ib)
T R..7 Nm (0.7 m •
kg, 5.1 ft • Ib)
T R..10 Nm (1.0 m • kg, 7.2 ft • Ib)
(3)
10
4
1 6
2
9
3
11
7
5 8
Extent of removal Order Part name Q
’ty Remarks
Drain the engine oil. Refer to “ENGINE OIL REPLACEMENT ”
section in the CHAPTER 3.
1 Drive sprocket cover 1
2 Drive sprocket 1
3 Shift pedal 1
4 Brake pedal 1
5 Footrest 1
6 Crankcase breather hose 1
7 Engine mounting bolt (front upper side) 1
8 Engine bracket 1
1