2006 YAMAHA TTR50 ignition

3 - 3
INSPADJ
PRE-OPERATION INSPECTION AND MAINTENANCE
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Fuel Check that a fresh gasoline is filled in the fuel tank. Check the fuel line
for leakage. P.1-11
Engine oil Check that the oil level is correct. Check the crankcase for leakage. P.3-7 ~ 9
Throttle Check for proper throttle cable operation. P.3-4 ~ 5
Brakes Check the play of front and rear brake and effect of front and rear
brake. P.3-14 ~ 15
Drive chain Check chain slack and alignment. Check that the chain is lubricated
properly. P.3-16 ~ 18
Wheels and tires Check pressure/runout/spoke tightness/bead stopper/axle nuts. P.3-19 ~ 20
Steering Check that the handlebar can be turned smoothly and have no exces-
sive play. P.3-20 ~ 21
Front forks and rear
shock absorber assembly Check that they operate smoothly and there is no oil leakage. P.3-18
Cables (wires) Check that the throttle cable move smoothly. Check that they are not
caught when the handlebars are turned. —
Muffler Check that the muffler is tightly mounted and has no cracks. P.4-3
Sprocket Check that the driven sprocket tightening nut is not loose. P.3-15
Lubrication Check for smooth operation. Lubricate if necessary. P.3-22
Spark plug Check color/condition. P.3-23
Fittings/fasteners Check all – tighten as necessary. P.2-13
Lead connectors Check that the AC magneto, CDI unit, and ignition coil are connected
tightly. P.1-5

3 - 31
INSPADJ
FUSE INSPECTION
3. Check:
Continuity
2 Reserve fuse
Checking steps:

Remove the fuse 1
.
 Connect the pocket tester to the fuse and
check the continuity.
NOTE:
Set the pocket tester selector to “Ω × 1 ”.
Pocket tester:
YU-03112-C/90890-03112
 If the pocket tester indicates “∞ ”, replace
the fuse.
1 2
4. Replace:
Blown fuse
WARNING
Never use a fuse with an amperage rating
other than that specified. Improvising or
using a fuse with the wrong amperage rat-
ing may cause extensive damage to the
electrical system, cause the starting and
ignition systems to malfunction and could
possibly cause a fire.
5. Connect:
Battery lead coupler
(to the battery terminals)
6. Install: Battery cover
 Seat assembly
Replacement steps:

Set the main switch to “OFF ”.
 Install a new fuse of the correct amperage.
 Set on the switches to verify if the electri-
cal circuit is operational.
 If the fuse immediately blows again, check
the electrical circuit.
Items Amperage
rating Q
’ty
Main fuse 10 A 1

4 - 9
ENGCARBURETOR
Fuel filter
1. Inspect:Fuel filter 1
Damage → Replace.
1
ASSEMBLY AND INSTALLATION
Carburetor
1. Install:
Clip 1
NOTE:
Align the space b between the clip ends with
the slit a of the throttle valve.
1
a
b
2. Install: Starter plunger 1
NOTE:
Align the slit a of the throttle valve with the tab
b of the carburetor top.
1
ba
FUEL LEVEL ADJUSTMENT
WARNING
Gasoline (fuel) and its vapors are highly
flammable and explosive. Keep away from
sparks, cigarettes, flames or other sources
of ignition.
1. Measure:
Fuel level a
Use a fuel level gauge 1.
Out of specification → Adjust.
Fuel level gauge:
YM-01312-A/90890-01312
Fuel level:2.0 ~ 3.0 mm (0.08 ~ 0.12 in)
Below the float chamber mating
surface
a
1

6 - 1
–+ELEC
345
6
78
\b0
B\f
2
1
ELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC600000
ELECTRICAL
EC610000
ELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC611000
ELECTRICAL COMPONENTS
1 Thermo switch
2 Main switch
3 Engine stop switch
4 Ignition coil
5 Ground lead
6 Fuse
7 Battery
8 CDI unit
9 Starter relay 0
Rectifier/regulator
A Neutral switch
B AC magneto
C Carburetor heater
D Start switch
E Spark plug
F Starter motorCOLOR CODE
B ...................... Black
Br .................... Brown
O ..................... Orange
R ..................... Red
Sb .................... Sky blue
W ..................... White
Y ...................... Yellow
EC612000
WIRING DIAGRAM
R
WR
W
BL /WSb B
RW
W
W
OO
B
B
Y /R
R
W
B
R
Y /RY /R
Y
ON
OFF
OFF ON
Y
B
BY
/RRB
SbY /RR B
W
B
B
RBrR
Br
R
/WBr
R /W
L /W
OFF
RUN
Sb
BrBr
Sb
WBY
/RW SbY
B
B
B
RR
RR
R
R
R
/W
L /W
RRRB
R /W
L
/WR
R
RR
B Br
BO
R
WB
\f
2 8
4
E
1
C
D
0
63
\b F
5 7
Br
L/W .................. Blue/White
R/W .................. Red/White
Y/R ................... Yellow/Red
E
F
D
C

–+ELEC
6 - 2
IGNITION SYSTEM
EC620000
IGNITION SYSTEM
INSPECTION STEPS
Use the following steps for checking the possibility of the malfunctioning engine being attributable to
ignition system failure and for checking the spark plug which will not spark.
NOTE:
Remove the following parts before inspection.
1) Seat assembly
2) Air scoops (left and right)
3) Fuel tank
Refer to “FRONT FENDER, SEAT ASSEMBLY AND FUEL TANK ” section in the CHAPTER 4.
 Use the following special tools in this inspection.
Opama pet-4000 spark checker:
YM-34487
Ignition checker: 90890-06754Pocket tester:YU-03112-C/90890-03112
Spark gap test Clean or replace
spark plug.
Check entire ignition
system for connection. Repair or replace.
Check main switch. Replace.
Check engine stop switch. Replace.
Check ignition coil. Primary coil Replace. Secondary coil Replace.
Check AC magneto. Pickup coil Replace. Replace CDI unit.
No Spark
OK
OK
OK
OK
OK
Spark
No good
No good
No good
No good
No good
No good

6 - 3
–+ELECIGNITION SYSTEM
EC622001
SPARK GAP TEST
1. Disconnect the spark plug cap from spark
plug.
2. Connect the opama pet-4000 spark
checker 1 (ignition checker 2) as shown.
 Spark plug cap 3
 Spark plug 4
È For USA and CDN
É Except for USA and CDN
3. Turn the main switch to
“ON ”.
4. Push the starter switch.
5. Check the ignition spark gap.
6. Start engine, and increase spark gap until misfire occurs. (for USA and CDN only)
Minimum spark gap:6.0 mm (0.24 in)
È
É
EC624000
COUPLERS AND LEADS CONNECTION
INSPECTION
1. Check:
Couplers and leads connection
Rust/dust/looseness/short-circuit →
Repair or replace.
MAIN SWITCH INSPECTION
1. Inspect: Main switch continuity
Check for continuity as follows:
Incorrect continuity → Replace.
Tester (+) lead
→ Red lead
1
Tester ( –) lead
→ Brown lead
2
R
1 Br
2 Tester selec-
tor position
ON Ω
× 1
OFF
Br
R
1 2

6 - 4
–+ELECIGNITION SYSTEM
ENGINE STOP SWITCH INSPECTION
1. Inspect:
Engine stop switch continuity
Continuous in the “” position → Replace.
Not continuous in the “” position → Replace.
Tester (+) lead
→ Black lead
1
Tester ( –) lead
→ Black lead
2
B
1 B
2 Tester selec-
tor position
Ω
× 1B
B
1 2
EC626002
IGNITION COIL INSPECTION
1. Inspect:
Primary coil resistance
Out of specification → Replace.
2. Inspect: Secondary coil resistance
Out of specification → Replace.
NOTE:
When inspecting the secondary coil resis-
tance, remove the spark plug cap.Tester (+) lead
→ Orange lead
1
Tester ( –) lead
→ Black lead
2
Primary coil
resistance Tester selector
position
0.32 ~ 0.48 Ω at
20 °C (68 °F) Ω

× 1
Tester (+) lead → Spark plug lead
1
Tester ( –) lead
→ Orange lead
2
Secondary coil
resistance Tester selector
position
5.68 ~ 8.52 k Ω
at 20 °C (68 °F) k
Ω
× 1
1
2
1
2

6 - 5
–+ELECIGNITION SYSTEM
AC MAGNETO INSPECTION
1. Inspect:
Pickup coil resistance
Out of specification → Replace.
Tester (+) lead → Red lead
1
Tester ( –) lead
→ White lead
2
Pickup coil
resistance Tester selector
position
248 ~ 372 Ω at
20 °C (68 °F) Ω

× 100
W
R
1 2