2006 YAMAHA SLIDER 50 turn signal

GIVE SAFETY THE RIGHT OF WAY
1
EAU03099
Further safe-riding points•
Be sure to signal clearly when making turns.
•
Braking can be extremely difficult on a wet road. Avoid hard braking, because the scooter could slide.
Apply the brakes slowly when stopping on a wet surface.
•
Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
•
Be careful when passing parked cars. A driver might not see you and open a door in your path.
•
Railroad crossings, streetcar rails, iron plates on road construction sites, and manhole covers become
extremely slippery when wet. Slow down and cross them with caution. Keep the scooter upright, otherwise
it could slide out from under you.
•
The brake pads could get wet when you wash the scooter. After washing the scooter, check the brakes
before riding.
•
Always wear a helmet, gloves, trousers (tapered around the cuff and ankle so they do not flap), and a
bright colored jacket.
•
Do not carry too much luggage on the scooter. An overloaded scooter is unstable.
1-2

INSTRUMENT AND CONTROL FUNCTIONS
3
12 34
ZAUM0522
EAU03034
Indicator and warning lights
EAU00057
Turn signal indicator light “
”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.
1. Fuel level warning light “
”
2. Turn signal indicator light “
”
3. Oil level warning light “
”
4. High beam indicator light “”
EAU00063
High beam indicator light “
”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU02958
Oil level warning light “
”
This warning light comes on when the
key is in the “
*
” position or when the
oil level in the 2-stroke engine oil tank
is low during operation. If the warning
light comes on during operation, stop
immediately and fill the oil tank with
Yamalube 2 or equivalent 2-stroke
engine oil of either JASO grade "FC"
or ISO grades "EG-C" or "EG-D". The
warning light should go off after the 2-
stroke engine oil tank has been refilled.
NOTE :
If the warning light does not come on
when the key is in the “
*
” position or
does not go off after the 2-stroke engine
oil tank has been refilled, have a
Yamaha dealer check the electrical cir-
cuit.
EC000000
Do not operate the scooter until you
know that the engine oil level issufficient.
3-2
ZAUM0524
EAUM0112
Fuel level warning light “
”
This warning light comes on and the
last two segments of the fuel meter will
start to flash when the fuel level drops
below approximately 1.4 L . When this
occurs, refuel as soon as possible.

INSTRUMENT AND CONTROL FUNCTIONS
3
12
3
ZAUM0142
1
ZAUM0473
1
ZAUM0084
1. Horn switch “
”
2. Turn signal switch “
”
3. Dimmer switch “
,
”1. Start switch “
”1. Front brake lever
EAU00118
Handlebar switches
EAU00125
Turn signal switch “
”
To signal a right-hand turn, push this
switch to the right. To signal a left-hand
turn, push this switch to the left. When
released, the switch returns to the
center position. To cancel the turn si-
gnal lights, push the switch in after it
has returned to the center position.
EAU00129
Horn switch “
”
Press this switch to sound the horn.
EAU03888
Dimmer switch “
,
”
Set this switch to “
” for the high beam
and to “
” for the low beam.
EAUM0063
Start switch “
”
Push this switch while applying the front
or rear brake to crank the engine with
the starter.
EC000005
See page 5-1 for starting instruc-tions prior to starting the engine.
EAU03882
Front brake leverThe front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the
handlebar grip.
3-4

OPERATION AND IMPORTANT RIDING POINTS
5
ZAUM0525
EAU00433
Starting offNOTE :
Before starting off, allow the engine towarm up.
1. While pulling the rear brake lever
with your left hand and holding the
grab bar with your right hand,
push the scooter off the
centerstand.
2. Sit astride the seat, and then
adjust the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip
(on the right) in order to take off.
5. Switch the turn signal off.
EAU01258
Starting a warm engineFollow the same procedure as for
starting a cold engine with the excep-
tion that the starter (choke) is not
required when the engine is warm.
ECA00045
For maximum engine life, never
accelerate hard when the engine iscold!
5. When the engine is warm, turn the
starter (choke) off.NOTE :
The engine is warm when it responds
normally to the throttle with the starter(choke) turned off.
5-2
EC000046
See page 5-4 for engine break-in ins-
tructions prior to operating thevehicle for the first time.

EAU00462
PERIODIC MAINTENANCE AND MINOR REPAIR
Periodic maintenance and lubrication chart ............ 6-2
Checking the spark plug ......................................... 6-5
Final transmission oil .............................................. 6-6
Cleaning the air filter element ................................. 6-7
Adjusting the carburetor .......................................... 6-8
Adjusting the throttle cable free play ....................... 6-8
Tires ........................................................................ 6-9
Cast wheels .......................................................... 6-11
Adjusting the front brake lever free play ............... 6-11
Adjusting the rear brake lever free play ................ 6-11
Checking the front brake pads
and rear brake shoes ............................................ 6-12
Checking the brake fluid level ............................... 6-13
Changing the brake fluid ....................................... 6-14
Checking and lubricating the cables ..................... 6-14
6 Checking and lubricating the throttle grip
and cable .............................................................. 6-15
Lubricating the front and rear brake levers ........... 6-15
Checking and lubricating the centerstand ............. 6-15
Checking the front fork .......................................... 6-16
Checking the steering ........................................... 6-16
Checking the wheel bearings ................................ 6-17
Battery ................................................................... 6-17
Replacing the fuse ................................................ 6-19
Replacing a headlight bulb .................................... 6-20
Replacing a front turn signal light bulb .................. 6-21
Replacing a rear turn signal light bulb or
the tail/brake light bulb .......................................... 6-21
Troubleshooting .................................................... 6-21
Troubleshooting chart ........................................... 6-22

PERIODIC MAINTENANCE AND MINOR REPAIR
6
2 1
ZAUM0531
1
2
ZAUM05321. Lens
2. Screw (x2)
6-21
EAU01623
Replacing the tail/brake light
bulb1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by
pushing it in and turning it
counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it
clockwise until it stops.
4. Install the lens by installing the
screws.
EC000108
Do not overtighten the screws,otherwise the lens may break.
EAU03497
Replacing a turn signal light
bulb1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it
counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it
clockwise until it stops.
4. Install the lens by installing the
screw.
ECA00065
Do not overtighten the screw,otherwise the lens may break.
EAU01008
TroubleshootingAlthough Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems
yourself. However, should your scoo-
ter require any repair, take it to a
Yamaha dealer, whose skilled
technicians have the necessary tools,
experience, and know-how to service
the scooter properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
1. Screw
2. Lens

SPECIFICATIONS
8
8-3 Electrical:
Ignition system type C.D.I
Charging system Flywheel magneto
BatteryModel GM4-3B, YB4L-B, FB4-B
Voltage/capacity 12 V / 4 Ah
Headlight type:Bulb
Bulbs (voltage/wattage x quantity):
Headlight 12V, 35W/35Wx1
Tail/brake light 12V, 5W/21Wx1
Turn signal light
Front 12V, 10Wx2
Rear 12V, 10Wx2
Meter lights 12V, 1.2Wx2
High beam indicator light 12V, 2Wx1
Turn signal indicator light 12V, 2Wx1
Oil level warning light 12V, 2Wx1
Fuel level warning light 12V, 2Wx1
Fuses:
Main fuse 7A