2006 YAMAHA FX HO fuel cap

3-8
E
4. Remove the oil tank filler cap 1, wipe
the dipstick clean, and then screw the
filler cap into the filler hole completely.
Remove the filler cap again and check
that the oil level is between the minimum
level mark 3 and maximum level
mark2 on the dipstick.
5. If the oil level is below the minimum level
mark, add enough oil so that the oil level
is between the minimum and maximum
level marks on the dipstick, and then
install the filler cap. If the engine oil level
is significantly above the maximum level
mark, the oil tank is overfilled. Have a
Yamaha dealer remove the excessive
amount of engine oil.
EJU19610
Water separator
Check the water separator 1 for water.
Normally the water separator is empty. The
water separator retains any water entering
through the fuel tank breather hose if the
watercraft is capsized.
If water remains in the water separator,
drain it by removing the drain screw 2.
Place a drain pan under the water separator
to catch the draining water or use a dry cloth
to soak up any water that could spill into the
watercraft. If any water spills into the water-
craft, be sure to wipe it up with a dry cloth.
Be sure to install the drain screw after drain-
ing the water separator.
E_F1X-70.book Page 8 Friday, August 26, 2005 11:00 AM

3-9
E
EJU18042
Bilge
Check for moisture and fuel residue in the
bilge.
This watercraft is equipped with a conven-
tional jet vacuum bilge draining system and
an electric bilge draining system. The elec-
tric bilge draining system is operated when
the engine is running. When excess water
reaches the water inlet of the electric bilge
pump, the water is discharged from the elec-
tric bilge pilot outlet 1 at the stern.
A small quantity of water will remain in the
bilge and should be removed manually. To
remove any residual water, beach the water-
craft and perform the following procedure.
CAUTION:@ If starting the engine after it has cap-
sized, do not operate the engine at full
open throttle when water is being dis-
charged from the electric bilge pilot out-
let at the stern. Excessive water in the
bilge can splash into the engine which
could cause damage.
@
To remove water from the bilge:
1. Remove the stern drain plugs.
2. Raise the bow of the watercraft until the
water drains.
3. After the water has drained, wipe the
bilge with dry rags to make sure that the
bilge is thoroughly dry.
4. Install the drain plugs.
E_F1X-70.book Page 9 Friday, August 26, 2005 11:00 AM

4-4
E
EJU19652
Fuel system
WARNING@ GASOLINE AND ITS VAPORS ARE
HIGHLY FLAMMABLE AND EXPLOSIVE!

Do not smoke when refueling, and
keep away from sparks, flames, or
other sources of ignition.

Stop engine before refueling.

Refuel in a well-ventilated area with
the watercraft in a horizontal position.

Do not stand or sit on the watercraft
while refueling in case of fire.

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level reaches approx-
imately 50 mm (2 in) from the top of the
fuel tank. Fuel expands as it warms up
and could overflow if the fuel tank has
been overfilled. If temporarily leaving
the watercraft with a full fuel tank, do
not leave it in direct sunlight. Leave it
in a well-ventilated area with the water-
craft in a horizontal position.

Tighten the filler cap securely after
refueling.

If you should swallow some gasoline,
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.

If any gasoline spills onto your skin,
immediately wash with soap and
water. Change clothing if gasoline
spills on it.
@
Top off the fuel tank with fresh gasoline
and add fuel stabilizer and conditioner to the
fuel tank by following the manufacturer’s
instructions carefully.
E_F1X-70.book Page 4 Friday, August 26, 2005 11:00 AM

4-11
E
EJU18160
Inspecting the fuel system
WARNING@ Gasoline is highly flammable and explo-
sive. Failure to check for and repair any
fuel leakage could result in fire or explo-
sion. A fire or explosion can cause
severe injury or death. Shut off the
engine. Do not smoke. Avoid spilling
gasoline.
Fuel in hose is pressurized.
Fuel can spray out and cause injury or a
fire hazard if fuel line is disconnected.
Do not attempt to run engine with fuel
line disconnected.
@
Check the fuel system for leaks, cracks,
or malfunctions. If any problem is found,
consult a Yamaha dealer.
Check:

Fuel tank for water or dirt.

Fuel tank cap (seal) for damage.

Fuel tank for damage, cracks or leakage.

Fuel hose joint for leakage.

Fuel hose for cracks or other damage.

Air bleeding passages for leakage.
EJU18410
Fuel tank
Check the fuel tank 1 for leakage or
water in the tank. If water is found in the fuel
system or if the fuel tank needs to be
cleaned, have a Yamaha dealer service the
watercraft.
E_F1X-70.book Page 11 Friday, August 26, 2005 11:00 AM

4-25
E
EJU13590
Specifications
MODEL
ITEMUnit FX High Output/FX Cruiser High Output
WATERCRAFT CAPACITY
Maximum people on board Number of people 3
Maximum load capacity kg (lb) 240 (530)
DIMENSIONS
Length mm (in) 3,340 (131.5)
Width mm (in) 1,230 (48.4)
Height mm (in) 1,160 (45.7)/1,240 (48.8)
Dry weight kg (lb) 363 (800)/380 (838)
PERFORMANCE
Maximum output kW (PS) @ r/min 117.7 (160)@ 10,000
Maximum fuel consumption L/h (US gal/h, Imp gal/h) 45 (11.9, 9.9)
Cruising range at full throttle hr. 1.56
Trolling speed r/min 1,600–1,700
ENGINE
Engine type 4-stroke
Number of cylinders 4
Engine displacement
cm
3 (cu in)1,052 (64.2)
Bore & stroke mm (in) 76 ×
58 (2.99 ×
2.28)
Compression ratio 11.9:1
Valve clearance (cold)
Intake mm (in) 0.11–0.20 (0.0043–0.0079)
Exhaust mm (in) 0.25–0.34 (0.0098–0.0134)
Lubrication system Dry sump
Cooling system Water cooled
Starting system Electric starter
Ignition system TCI
Spark plug CR9EB (NGK)
Spark plug gap mm (in) 0.7–0.8 (0.028–0.031)
Battery capacity V-AH 12-19
Charging system Flywheel magneto
E_F1X-70.book Page 25 Friday, August 26, 2005 11:00 AM

4-26
E
DRIVE UNIT
Propulsion system Jet pump
Jet pump type Axial flow, single stage
Impeller rotation Counterclockwise (viewed from rear)
Jet thrust nozzle horizontal angle Degree 24 + 24
Jet thrust nozzle trim angle Degree -10, -5, 0, 5, 10
FUEL AND OIL
Recommended fuel Regular unleaded gasoline
Minimum octane rating PON
RON86
90
Recommended engine oil SAE 10W-30
API SE, SF, SG, SH, SJ, SL
Fuel tank capacity
Total L (US gal, Imp gal) 70 (18.5, 15.5)
Engine oil quantity
With oil filter replacement L (US qt, Imp qt) 2.3 (2.4, 2.0)
Without oil filter replacement L (US qt, Imp qt) 2.1 (2.2, 1.8)
Total amount L (US qt, Imp qt) 4.5 (4.8, 4.0)MODEL
ITEMUnit FX High Output/FX Cruiser High Output
E_F1X-70.book Page 26 Friday, August 26, 2005 11:00 AM

5-1
E
EJU11160
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible
cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described
in this Owner’s/Operator’s Manual, have a Yamaha dealer perform the necessary service.
EJU13670
Troubleshooting chart
TBC-F0P7ETROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
startStarter motor does not turn over
Yamaha
Security
SystemLock mode selected Select unlock mode
2-21
Engine shut-
off switchClip not in place Install clip
2-10
Fuse Burned out Replace the fuse and
check wiring4-24
Battery Run down Recharge 4-21
Poor terminal connec-
tionsTighten as required
4-21
Terminal corroded Clean 4-5
Starter motor Faulty Have serviced by
Yamaha dealer—
Starter motor turns over
Throttle lever Squeezed Release 2-11
Fuel Empty Refill as soon as possi-
ble3-4
Stale or contaminated Have serviced by
Yamaha dealer4-11
Fuel tank Water or dirt present Have serviced by
Yamaha dealer4-11
Spark plug Fouled or defective Clean or replace 4-16
Spark plug cap Not connected or loose Connect properly 4-16
Connected to wrong
cylinderConnect properly
4-16
Fuel injection
systemFuel pump faulty Have serviced by
Yamaha dealer—
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM

5-2
E
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as possi-
ble3-4
Stale or contaminated Have serviced by
Yamaha dealer4-11
Fuel tank Water or dirt present Have serviced by
Yamaha dealer4-11
Spark plug Fouled or defective Replace 4-16
Incorrect heat range Replace 4-16
Gap incorrect Adjust 4-16
Spark plug cap Loose Connect properly 4-16
Cracked, torn, or dam-
agedReplace
—
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel injection
systemJet nozzle clogged Have serviced by
Yamaha dealer—
Warning light or
indicator blinksFuel level Empty Refill as soon as possi-
ble3-4
Engine over-
heatedJet intake clogged Clean
5-3
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer—
Wate rcr af t slow or
loses powerYamaha
Security
SystemLow-RPM mode
selectedSelect normal mode
2-22
Cavitation Jet intake clogged Clean 5-3
Impeller damaged or
wornHave serviced by
Yamaha dealer—
Engine over-
heat warningEngine speed reduc-
tion control activatedClean jet intake and
cool engine2-30
Oil pressure
warningEngine speed reduc-
tion control activatedAdd oil
2-30
Spark plug Fouled or defective Replace 4-16
Incorrect heat range Replace 4-16
Gap incorrect Adjust 4-16
Spark plug
capsLoose Connect properly
4-16
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel Stale or contaminated Have serviced by
Yamaha dealer4-11
Air filter Clogged Clean or replace 4-14
Oil buildup Replace 4-14 TROUBLE POSSIBLE CAUSE REMEDY PAGE
E_F1X-70.book Page 2 Friday, August 26, 2005 11:00 AM