2006 YAMAHA FX HO engine

4-12
E
EJU21590
Changing the engine oil
WARNING@ Engine oil is extremely hot immediately
after the engine is turned off. Coming
into contact with or getting any engine
oil on your clothes could result in burns.
@
CAUTION:@
Do not run the engine with too much or
not enough oil in the oil tank. Oil could
spray out and the engine could be
damaged.

Be sure to change the engine oil after
the first 10 hours of operation, and
every 100 hours thereafter or at the
start of a new season, otherwise the
engine will wear quickly.
The oil filter should be replaced every
year or every 100 hours of operation.
Have a Yamaha dealer replace the oil
filter if necessary.
@
It is recommended to have a Yamaha
dealer change the engine oil. However, if
you choose to change the oil on your own,
consult a Yamaha dealer.
NOTE:@ Dispose of used oil according to local regu-
lations.
@
Recommended engine oil:
See page 3-3.
Oil quantity:
With oil filter replacement:
2.3 L (2.4 US qt, 2.0 Imp qt)
Without oil filter replacement:
2.1 L (2.2 US qt, 1.8 Imp qt)
Total amount:
4.5 L (4.8 US qt, 4.0 Imp qt)
E_F1X-70.book Page 12 Friday, August 26, 2005 11:00 AM

4-13
E
CAUTION:@ If oil is leaking or the oil pressure warn-
ing indicator comes on when the engine
is running, immediately turn the engine
off and have a Yamaha dealer check the
watercraft. Continuing to operate the
engine under such conditions could
cause severe engine damage.
@
E_F1X-70.book Page 13 Friday, August 26, 2005 11:00 AM

4-14
E
EJU18190
Checking the air filter element
The air filter element should be checked
every 12 months or every 100 hours of oper-
ation.
To check the air filter:
1. Remove the rear and front seats. (See
pages 2-5 and 2-6 for seat removal and
installation procedures.)
2. Remove the air filter case cover
screws1, slide the locks 2 open, and
then remove the case cover.
3. Remove the air filter element and check
it for dirt and oil. Replace the air filter ele-
ment if there is any oil buildup, or every
2 years or every 200 hours of operation.
4. Install the air filter element in the air filter
case, and then install the case cover.
CAUTION:@
Make sure that the air filter element is
installed in the filter case properly.

Do not start the engine with the air fil-
ter element removed, otherwise the
pistons and cylinders could be dam-
aged.

If cleaning the air filter element, use
cold or lukewarm water and let it air
dry completely. Do not use detergent
or solvent to clean the air filter ele-
ment, or dry it with heat or com-
pressed air, otherwise it could be
damaged.
@
E_F1X-70.book Page 14 Friday, August 26, 2005 11:00 AM

4-16
E
EJU21070
Cleaning and adjusting the
spark plugs
The spark plug is an important engine
component and is easy to inspect. The con-
dition of the spark plug can indicate some-
thing about the condition of the engine. For
example, if one spark plug shows a distinctly
different color, the engine could be defec-
tive. Do not attempt to diagnose any prob-
lems yourself. Have a Yamaha dealer
service the watercraft.
Remove and inspect the spark plugs peri-
odically; heat and deposits will cause the
spark plugs to slowly break down and erode.
If electrode erosion becomes excessive, or if
carbon and other deposits are excessive,
replace the spark plug with the specified
plug.
Removing a spark plug:
1. Remove the air filter case cover and air
filter element. (See page 4-14 for air filter
removal and installation procedures.)
2. Remove the spark plug cap.
CAUTION:@ Do not use any tools to remove or install
the spark plug cap, otherwise the igni-
tion coil coupler may get damaged. The
spark plug cap may be difficult to remove
because the rubber seal on the end of
the cap fits tightly. To remove the spark
plug cap, simply twist it back and forth
while pulling it up; to install it, twist it
back and forth while pushing it down.
@
3. Remove the spark plug.
Specified spark plug: NGK CR9EB
E_F1X-70.book Page 16 Friday, August 26, 2005 11:00 AM

4-23
E
EJU18231
Adjusting the fuel injection
system
The fuel injection system was set at the
Yamaha factory. Have a Yamaha dealer ser-
vice the watercraft if necessary.
CAUTION:@ Do not attempt to adjust the fuel injection
system. If the settings are changed poor
engine performance and damage may
result.
@
EJU18240
Checking the trolling speed
1. Put the watercraft in the water.
2. Start the engine and warm it up. Use the
tachometer in the multifunction meter to
check the trolling speed.
If the trolling speed is out of specification,
have a Yamaha dealer make this adjust-
ment. Trolling speed: 1,600–1,700 r/min
E_F1X-70.book Page 23 Friday, August 26, 2005 11:00 AM

4-25
E
EJU13590
Specifications
MODEL
ITEMUnit FX High Output/FX Cruiser High Output
WATERCRAFT CAPACITY
Maximum people on board Number of people 3
Maximum load capacity kg (lb) 240 (530)
DIMENSIONS
Length mm (in) 3,340 (131.5)
Width mm (in) 1,230 (48.4)
Height mm (in) 1,160 (45.7)/1,240 (48.8)
Dry weight kg (lb) 363 (800)/380 (838)
PERFORMANCE
Maximum output kW (PS) @ r/min 117.7 (160)@ 10,000
Maximum fuel consumption L/h (US gal/h, Imp gal/h) 45 (11.9, 9.9)
Cruising range at full throttle hr. 1.56
Trolling speed r/min 1,600–1,700
ENGINE
Engine type 4-stroke
Number of cylinders 4
Engine displacement
cm
3 (cu in)1,052 (64.2)
Bore & stroke mm (in) 76 ×
58 (2.99 ×
2.28)
Compression ratio 11.9:1
Valve clearance (cold)
Intake mm (in) 0.11–0.20 (0.0043–0.0079)
Exhaust mm (in) 0.25–0.34 (0.0098–0.0134)
Lubrication system Dry sump
Cooling system Water cooled
Starting system Electric starter
Ignition system TCI
Spark plug CR9EB (NGK)
Spark plug gap mm (in) 0.7–0.8 (0.028–0.031)
Battery capacity V-AH 12-19
Charging system Flywheel magneto
E_F1X-70.book Page 25 Friday, August 26, 2005 11:00 AM

4-26
E
DRIVE UNIT
Propulsion system Jet pump
Jet pump type Axial flow, single stage
Impeller rotation Counterclockwise (viewed from rear)
Jet thrust nozzle horizontal angle Degree 24 + 24
Jet thrust nozzle trim angle Degree -10, -5, 0, 5, 10
FUEL AND OIL
Recommended fuel Regular unleaded gasoline
Minimum octane rating PON
RON86
90
Recommended engine oil SAE 10W-30
API SE, SF, SG, SH, SJ, SL
Fuel tank capacity
Total L (US gal, Imp gal) 70 (18.5, 15.5)
Engine oil quantity
With oil filter replacement L (US qt, Imp qt) 2.3 (2.4, 2.0)
Without oil filter replacement L (US qt, Imp qt) 2.1 (2.2, 1.8)
Total amount L (US qt, Imp qt) 4.5 (4.8, 4.0)MODEL
ITEMUnit FX High Output/FX Cruiser High Output
E_F1X-70.book Page 26 Friday, August 26, 2005 11:00 AM

5-1
E
EJU11160
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible
cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described
in this Owner’s/Operator’s Manual, have a Yamaha dealer perform the necessary service.
EJU13670
Troubleshooting chart
TBC-F0P7ETROUBLE POSSIBLE CAUSE REMEDY PAGE
Engine does not
startStarter motor does not turn over
Yamaha
Security
SystemLock mode selected Select unlock mode
2-21
Engine shut-
off switchClip not in place Install clip
2-10
Fuse Burned out Replace the fuse and
check wiring4-24
Battery Run down Recharge 4-21
Poor terminal connec-
tionsTighten as required
4-21
Terminal corroded Clean 4-5
Starter motor Faulty Have serviced by
Yamaha dealer—
Starter motor turns over
Throttle lever Squeezed Release 2-11
Fuel Empty Refill as soon as possi-
ble3-4
Stale or contaminated Have serviced by
Yamaha dealer4-11
Fuel tank Water or dirt present Have serviced by
Yamaha dealer4-11
Spark plug Fouled or defective Clean or replace 4-16
Spark plug cap Not connected or loose Connect properly 4-16
Connected to wrong
cylinderConnect properly
4-16
Fuel injection
systemFuel pump faulty Have serviced by
Yamaha dealer—
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM