2006 YAMAHA FX HO CRUISER engine overheat

4-3
E
EJU18980
Lubrication
WARNING@ Do not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance or
propellants could catch fire.
@
1. Remove the rear and front seats. (See
pages 2-5 to 2-6 for seat removal and
installation procedures.)
2. Remove the air filter case cover
screws1, slide the locks 2 open, and
then remove the case cover.
3. Remove the air filter case cover and air
filter element.
4. Spray a rust inhibitor into each intake
opening 3 for 3 seconds.
5. Install the air filter element and air filter
case cover.
6. Start the engine in a well-ventilated area
and let it run at idle for 15 seconds.
CAUTION:@ Do not run the engine for more than
15 seconds. The engine could overheat.
@
7. Lubricate all cables such as the throttle
and steering cables.
NOTE:@ Use a suitable marine grease applicator to
pressure lubricate the cables and purge out
any moisture between the inner and outer
cables.
@
8. Lubricate the areas of the watercraft
specified under Lubrication points on
page 4-18.
E_F1X-70.book Page 3 Friday, August 26, 2005 11:00 AM

5-3
E
EJU11180
Emergency procedures
EJU21602
Cleaning the jet intake and
impeller
If weeds or debris get caught in the intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine
speed rises. If this condition is allowed to
continue, the engine will overheat and may
seize. If there is any sign that the jet intake
or impeller is clogged with weeds or debris,
return to shore and check the intake and
impeller. Always stop the engine before
beaching the watercraft.
WARNING@ Before attempting to remove weeds or
debris from the jet intake or impeller
area, shut the engine off and remove the
clip from the engine shut-off switch.
Severe injury or death could result from
coming in contact with the rotating parts
of the jet pump.
@
CAUTION:@ If weeds or debris get caught in the
intake, do not operate the watercraft
above trolling speed until they have been
removed.
@
1. Turn the watercraft on its side as shown.
E_F1X-70.book Page 3 Friday, August 26, 2005 11:00 AM

6-1
E
EJU11250
Index
A
Adjusting the fuel injection system ........ 4-23
Analog speedometer/tachometer .......... 2-24
Analog speedometer/tachometer and
indicator lights ....................................... 2-24
Approval label of Emission control
certificate ................................................. 1-4
B
Battery ............................................ 3-10, 4-5
Beaching the watercraft ........................ 3-34
Beverage holder .................................... 2-38
Bilge ........................................................ 3-9
Boarding alone ...................................... 3-26
Boarding and starting in deep water ..... 3-26
Boarding with passengers ..................... 3-27
Bow down.............................................. 2-17
Bow up .................................................. 2-17
Builder’s plate.......................................... 1-3
C
Capsized watercraft .............................. 3-29
Changing the engine oil ........................ 4-12
Check engine warning indicator ............ 2-29
Checking the air filter element............... 4-14
Checking the trolling speed ................... 4-23
Cleaning and adjusting the
spark plugs ............................................ 4-16
Cleaning the jet intake and impeller ........ 5-3
Cleaning the watercraft ........................... 4-6
Connecting the jumper cables................. 5-6
Cooling water pilot outlet .............. 2-12, 3-16
Cruising limitations ................................ 1-14
D
Digital speedometer .............................. 2-27
Docking the watercraft .......................... 3-34
E
Emergency procedures ........................... 5-3
Emission control information
(For Canada only) ................................... 1-4
Engine break-in ..................................... 3-17
Engine compartment ............................... 3-6Engine oil ................................................ 3-3
Engine oil level ........................................ 3-7
Engine overheat warning indicator ........ 2-30
Engine serial number .............................. 1-2
Engine shut-off cord (lanyard) ............... 3-15
Engine shut-off switch ........................... 2-10
Engine stop switch ................................ 2-10
Enjoy your watercraft responsibly ......... 1-21
F
Filling the fuel tank .................................. 3-4
Fire extinguisher .................................... 3-11
Flushing the cooling system .................... 4-1
Front seat ................................................ 2-6
Front storage compartment ................... 2-36
Fuel and oil.............................................. 3-1
Fuel level ................................................. 3-6
Fuel meter ............................................. 2-28
Fuel system ............................................. 4-4
Fuel tank ............................................... 4-11
Fuel tank filler cap ................................... 2-7
Fuel warning indicator ........................... 2-29
G
Gasohol ................................................... 3-2
Gasoline .................................................. 3-1
Getting to know your watercraft ............ 3-22
Glove compartment ............................... 2-37
H
Handgrip ................................................ 2-18
Hazard information ................................ 1-18
Hood........................................................ 2-7
Hour meter/Voltmeter ............................ 2-28
Hull and deck .......................................... 3-6
Hull Identification Number (HIN).............. 1-2
I
Identification numbers ............................. 1-1
Important labels ....................................... 1-5
Inspecting and adjusting the
throttle cable.......................................... 4-15
Inspecting the battery ............................ 4-21
Inspecting the fuel system ..................... 4-11
Inspecting the jet thrust nozzle angle .... 4-15
Inspecting the shift cable ....................... 4-15
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM