2006 YAMAHA FX CRUISER check engine

1-16
E

Do not attempt to modify this watercraft!
Modifications to your watercraft may
reduce safety and reliability, and render
the watercraft unsafe or illegal for use.

Attach the engine shut-off cord (lanyard)
to your wrist and keep it free from the
handlebars so that the engine stops if the
operator falls off. After riding, remove the
engine shut-off cord from the watercraft to
avoid accidental starting or unauthorized
use by children or others.

Scan carefully for swimmers and stay
away from swimming areas. Swimmers
are hard to see and you could acciden-
tally hit someone in the water.

Avoid being hit by another boat! You
should always take the responsibility to
watch for traffic; other boaters may not be
watching for you. If they do not see you,
or if you maneuver more quickly than
other boaters expect, you risk a collision.

Maintain a safe distance from other boats
and watercraft, and also watch for ski
ropes or fishing lines. Obey the “Safe
boating rules,” and be sure to check
behind you before making a turn. (See
Safe boating rules on page 1-20.)
EJU01382
Recommended equipment
The following items should be carried on
board your watercraft:

Sound-signaling device
You should carry a whistle or other sound-
signaling device that can be used to sig-
nal other boats.

Visual distress signals
It is recommended that an authority-
approved pyrotechnic device be stored in
a waterproof container on your watercraft.
A mirror can also be used as an emer-
gency signal. Contact your Yamaha
dealer for more information.

Watch
A watch is helpful so you will know how
long you have been operating.

Towline
A towline can be used to tow a disabled
watercraft in an emergency.
E_F1Y-70.book Page 16 Friday, August 26, 2005 9:47 AM

2-3
E
1Quick Shift Trim System (QSTS) selector
Use to select the trim angle of the watercraft.
2QSTS shift lock lever
3Watertight compartment
4Start switch
Push to start the engine.
5Engine shut-off switch
Remove the clip to stop the engine and dis-
able it from starting.
6Clip
Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent acci-
dental star ting of the engine or unauthorized
use of the watercraft.
7Multifunction meter
Use to check watercraft operation.8Beverage holder
9Rearview mirrors
0Throttle lever
Use to accelerate and decelerate.
AShift lever
Use to put the watercraft into forward or
reverse.
BTilt lever
Use to adjust the tilt of the handlebars.
CGlove compartment
DEngine stop switch
Push to stop the engine normally.
EEngine shut-off cord (lanyard)
Attach to wrist so that the engine stops if the
operator falls off the watercraft.
E_F1Y-70.book Page 3 Friday, August 26, 2005 9:47 AM

2-9
E
EJU01861
Start switch
Push the start switch 1 (green button) to
start the engine.
NOTE:@ The engine will not start when the clip is
removed from the engine shut-off switch or if
the throttle lever is squeezed.
EJU01784
Cooling water pilot outlet
This watercraft is equipped with cooling
water pilot outlets.
When the engine is running, cooling
water is circulated in the engine, and then it
is discharged from the pilot outlets.
To check for proper operation of the cool-
ing system, check that water is being dis-
charged from the port (left) pilot outlet. If
water is not being discharged from this out-
let, cooling water may not be circulating in
the engine. When this occurs, stop the
engine and check for the cause. (See pages
2-24 and 5-3 for further instructions.)
NOTE:@
If the cooling water passages are dry, it
will take about 60 seconds for the water to
reach the outlet after the engine is
started.

Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.

Water discharge may not be constant at
the starboard (right) pilot outlet, however,
if it is constant at the port (left) pilot outlet,
the cooling system is operating normally.
E_F1Y-70.book Page 9 Friday, August 26, 2005 9:47 AM

2-16
E
EJU19940
Yamaha Engine Management
System (YEMS)
This model is equipped with an inte-
grated, computerized management system
that controls and adjusts ignition timing, fuel
injection, engine diagnostics, and the Off-
Throttle Steering (OTS) system.
EJU22340
Multifunction meter
The multifunction meter is equipped with
the following two main components for help
and convenience in operating the watercraft.
1
Analog speedometer/tachometer and indicator
lights
2
Multifunction display and operation buttons
CAUTION:@ Do not run the engine for more than
15 seconds when checking the operation
of the meter on land. The engine could
overheat.
@
NOTE:@
When the multifunction meter starts oper-
ating, the analog speedometer/tachome-
ter makes one sweep, all displays light up
for 2 seconds, and then the meter starts
to operate normally.

The multifunction meter will continue to
operate for 25 seconds after the engine
stops.
@
E_F1Y-70.book Page 16 Friday, August 26, 2005 9:47 AM

2-20
E
EJU22040
Left multifunction display and
operation buttons
The left multifunction display is equipped
with the following functions.
1
Digital speedometer
2
Fuel meter
3
Hour meter/Voltmeter
4
Check engine warning indicator
5
Fuel warning indicator
6
Oil pressure warning indicator
7
Engine overheat warning indicator
The following operation buttons are on the
left side of the multifunction meter.
8
“Volt/Hour” button
9
“Speed/RPM” button
EJU22270
Digital speedometer
The digital speedometer 1
shows the
watercraft speed against water.
NOTE:@
To switch the speedometer display
between kilometers and miles, push the
“Vo l t / H o u r” button 2
for at least 1 second,
within 10 seconds after the multifunction
meter starts operating.

The “SPEED” indicator light 3
blinks
three times if miles are selected as the
display units when the multifunction meter
starts operating, or if the display units of
the meter are switched to miles.
@
E_F1Y-70.book Page 20 Friday, August 26, 2005 9:47 AM

2-21
E
EJU17890
Fuel meter
The fuel meter is provided for convenient
fuel level checking while riding. The fuel
meter has eight segments which show the
amount of fuel remaining in the fuel tank.
NOTE:@ The fuel level is most accurate when the
watercraft is sitting level on a trailer or in the
water.
@
EJU22050
Hour meter/Voltmeter
NOTE:@ To switch the display between the hour
meter and voltmeter, push the “Vo l t / H o u r”
button 1 for at least 1 second after the
meter is displayed for more than 10 sec-
onds.
@
Hour meter
The hour meter is provided to make it
easy to follow the maintenance schedule.
The meter shows the hours of engine
operation that have elapsed since the water-
craft was new.
Vo l t m e t e r
The voltmeter is provided to display the
voltage of the battery.
When the battery voltage is normal, the
voltmeter displays approximately 12 volts.
If the battery voltage is less than 8.0 volts,
“LO” is displayed on the voltmeter and if the
voltage is above 18.1 volts, “HI” is displayed
on the voltmeter. If “HI” or “LO” is displayed,
return to shore and, if necessary, have a
Yamaha dealer check the charging system
and the battery.
E_F1Y-70.book Page 21 Friday, August 26, 2005 9:47 AM

2-22
E
EJU22060
Check engine warning indicator
If a sensor malfunction or a short circuit is
detected, the “WARNING” indicator light and
the check engine warning indicator begin to
blink and the buzzer sounds intermittently.
If this occurs, reduce the engine speed,
return to shore, and have a Yamaha dealer
check the engine.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22070
Fuel warning indicator
If the fuel remaining in the tank drops to
about 13 L (3.4 US gal, 2.9 Imp gal), the
lowest two fuel level segments, the fuel
warning indicator, and the “WARNING” indi-
cator light all begin to blink. The buzzer also
starts sounding intermittently.
The warning signals will be cleared when
the engine is restarted after refilling.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
E_F1Y-70.book Page 22 Friday, August 26, 2005 9:47 AM

2-23
E
EJU22080
Oil pressure warning indicator
If the oil pressure does not rise to specifi-
cation, the “WARNING” indicator light and
the oil pressure warning indicator begin to
blink and the buzzer sounds intermittently.
At the same time, the engine speed is lim-
ited to help prevent damage.
If this occurs, reduce the engine speed,
return to shore, and then check the engine
oil level. (See page 3-7 for engine oil level
checking procedures.) If the oil level is low,
add enough engine oil to raise it to the
proper level. If the oil level is sufficient, have
a Yamaha dealer check the watercraft.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
E_F1Y-70.book Page 23 Friday, August 26, 2005 9:47 AM