WARNING
Do not exceed the load limit of 3 kgfor the front storage compartment.
■ ■■ ■
■Storage compartmentThe storage compartment locates
under seat, which can hold a full-cov-
ered helmet. When storing helmet,
place it upright, and the front side
should face the motorcycle head
(shown in the drawing above).
PARTS LIST AND OPERATION■ ■■ ■
■Fuel tank capThe fuel tank cap locates under the
rider seat, open the seat and you can
see the cap.
1. If you wish to remove the fuel tank
cap, turn it counterclockwise.
2. If you wish to fasten the fuel tank
cap, table the flange in the cap to the
groove in the fuel tank, and turn
clockwise.
3. Gasoline
Make sure that there is enough fuel in
the tank; fill the tank till the fuel reaches
the bottom of filler tube as per
illustration.
Fuel tank capacity: 5.4L
■ ■■ ■
■Front storage compartment
3-5
Fuel tank cap
2
1
■ ■■ ■
■Tyre1.Tyre pressure:
Adjust the tyre pressure to value
specified before riding.
2. Tyre casing
Check the situation of the tyre before
riding. If the tyre casing is over worn,
or there are pins or broken glasses, or
the tyre casing has crackles, ask the
agency to repair it, replace if
necessary.
■ ■■ ■
■Petrol levelMake sure that there is sufficient petrol
in the fuel tank.
WARNING
Do not splash or overfill the gaso-
line to the exhaust pipe when
fueling. There are agents equipped
in the exhaust pipe. The surface
temperature is very high, and it mayburn when the gasoline is spilled.■ ■■ ■
■Throttle gripPlace the throttle grip to check the
operation and free gaps. Make sure
that the grip will return to the original
position by spring force when releasing.
Ask the agency to adjust if necessary.Specified
fuel
CapacityOnly with unleaded petrol (#93 unleaded
fuel recommended)
5.4L totally
front tyre: 175Kpa
rear tyre: 200Kpa
front tyre: 175Kpa
rear tyre: 225Kpa 1 person Tyre pressure
2 persons
NOTE: Check the tyre pressure when the tyreis cooled.
WARNING
Never overload at any time,
otherwise, it may cause hazardbecause of tyre bursting.Check the front headlight, position light,
turn signal, rear light, stoplight, instru-
ment light and all the other indicator
lights, and make sure that they run
well.
■ ■■ ■
■SwitchesCheck the operation of the switches
for front headlight, position light, turn
signal, stoplight, horn and starter, main
switch.■ ■■ ■
■Lights and signal light
PRE-OPERATION CHECKS
6-3
foreign material (pin,gallet)
alligatoring, broke
wear limit indicator
3-5mn
SPECIFICATIONDimension and weightOverall length
Overall width
Overall height
Maximum load
Wheel baseMinimum ground clearanceBasic weight
1,860mm
670mm
1,045mm
153 ± 7kg
1,250mm ± 30mm
95mm ± 20mm
105kg ± 7kg4-stroke SOHC
Single cylinder, Forward inclined
125cc
51.5mm
× 60mm
9.5:1
electrical/kick-start
Forced lubrication
1.2L
■ ■■ ■
■Specification
Item Specification
Item Specification
Engine
ModelCylinder arrangementAir displacement
Bore x Stroke
Compression ratio
Starting system
LubricationE/G lubrication oil capacity
Electrical devices
Ignition spark modelAccumulator capacityAccumulator modelTransmission devicePrimary reductionReduction ratio(idem)Second reductionReduction ratio(idem)ClutchHelical gear
40/15
Spur gear
38/13
Dry, centrifugal
C7ER
12V, 6AH
GTX7A-BS/YTX7A-BS
Variable speed ratio
Model
Shift type
Variable speed ratioV-belt infinite variable speed
Infinite variable speed
0.852 - 2.572 FuelTank capacity
5.4L
9-1
