2006 YAMAHA BANSHEE 350 clock

4-19
EBU00092
Fuel tank cap
Remove the fuel tank cap by turning it counter-
clockwise.
EBU00093
Fuel cock
The fuel cock supplies fuel from the fuel tank to
the carburetor.
The fuel cock has three positions.
OFF: With the lever in this position fuel will not
flow. Always turn the lever to this position
when the engine is not running.
ON: With the lever in this position, fuel flows to
the carburetor. Normal riding is done with
the lever in this position.
RES: This indicates reserve. If you run out of
fuel while riding, turn the lever to this posi-
tion. THEN FILL THE FUEL TANK AT
THE FIRST OPPORTUNITY. After refu-
elling, return the fuel cock lever to the
“ON” position.
q
RES
ON
OFF
1. Fuel tank cap
1. Bouchon de réservoir de carburant
1. Tapón del depósito de combustible

8-93
EBU00351
Drive chain slack adjustment
1. Loosen the rear wheel hub bolts.
2. Loosen the adjuster locknuts on each side.
To tighten the chain, turn the chain
adjuster clockwise. To loosen the chain,
turn the adjuster counterclockwise and
push the wheel forward. Turn each
adjuster exactly the same amount to main-
tain correct axle alignment.
There are marks on each side of the
swingarm and on each chain adjuster. Use
them to check for proper alignment.
3. After adjusting, be sure to tighten the lock-
nuts and the wheel hub bolts.
q
w
e
q w
1. Upper wheel hub bolt (×2) 2. Lower wheel hub bolt (×2)
1. Boulon supérieur de moyeu de roue (×2)
2. Boulon inférieur de moyeu de roue (×2)
1. Tornillo superior del buje de rueda (×2)
2. Tornillo inferior del buje de rueda (×2)
1. Locknut 2. Ajuster 3. Alignment marks
1. Contre-écrou 2. Dispositif de réglage
3. Repères d’alignement
1. Contratuerca 2.Tensor3.Marcas de alineación
Upper wheel hub bolt:
120 Nm (12.0 m0kgf)
Lower wheel hub bolt:
60 Nm (6.0 m0kgf)

3. Turn the bulb holder counterclockwise to
remove the defective bulb.
w
A headlight bulb is hot when it is on and
immediately after it is turned off. Wait for the
bulb to cool before touching or removing it.
You can be burned, or a fire could start if the
bulb touches something flammable.
4. Put a new headlight bulb into position and
secure it in place with the bulb holder.
cC
Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of
the bulb, and the bulb life will be adversely
affected. Thoroughly clean off any dirt and
fingerprints on the headlight bulb using a
cloth moistened with alcohol or thinner.
5. Install the bulb holder cover.
1
e qw
r
1. Bulb holder
1. Douille d’ampoule
1. Portabombillas
1. Bulb holder cover 2. Bulb holder
3. Reflector
4. Do not touch the glass part of the bulb.
1. Cache de la douille d’ampoule 2. Douille d’ampoule
3. Réflecteur
4. Ne pas toucher le verre de l’ampoule.
1. Cubierta del portabombillas 2. Portabombillas
3. Reflector
4. Ne tocar la parte de cristal de la bombilla.
8-109

8-113
EBU00861
Tail/brake light bulb replacement
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
2. Remove the defective bulb from the bulb
holder by pushing it inward and turning it
counterclockwise.
3. Install a new bulb in the bulb holder by
pushing it inward and turning it clockwise.
4. Install the bulb holder (together with the
bulb).
1
q
w
1. Bulb holder
1. Fixation d’ampoule
1. Portabombillas
1. Bulb holder 2. Bulb
1. Fixation d’ampoule 2. Ampoule
1. Portabombillas 2. Bombilla