position.
pg. 68 Interior
Power seats
The power driver's seat can be adjusted:
If the ignition key is in position I or II.
During a 10 minute period after the doors have been unlocked if the door remains open.
If the door is closed and the ignition key is not yet in the ignition, or if the key is in position 0, the seat can be
adjusted or during a period of 40 seconds. The power passenger's seat can only be adjusted if the ignition key is in
position I or II, or if the engine is running.
Adjusting the seat
Controls 5, 6, and 7 on the side of the seat can be used to make adjustments.
5. Backrest tilt
6. Move this section of the control up or down to raise/lower the rear section of the seat. Move the control forward to
move the seat forward.
7. Move this section of the control up or down to raise/lower the front section of the seat. Move the control rearward
to move the seat rearward.
NOTE: The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs,
switch off the ignition (key in position 0) and wait for approximately 20 seconds before operating the seat again.
Emergency stop
NOTE: If the seat inadvertently begins to move, press any of the buttons to stop the seat.
Programming the seat memory, driver's seat only (option)
Three different seating positions can be stored (buttons 1, 2, and 3 in the illustration) in the seat's memory.
The following example explains how button 1 can be programmed. Buttons 2 and 3 can be programmed in the same
way.
To program (store) a seat position in button 1:
Use controls 5, 6, and 7 to adjust the seat to the desired position.
Press and hold down the M (memory) button.
With the M button depressed, press button 1 to store the seat's current position.
ProCarManuals.com
To move the seat to the position that it was in when button 1 was programmed, press and hold down button 1 until the
seat stops moving.
As a safety precaution, the seat will stop automatically if the button is released before the seat has reached the preset
position.
Central locking system remote control and driver's seat memory
The remote control transmitter can also be equipped with an optional function that controls the electrically operated
driver's seat in the following way:
Adjust the seat to the desired position.
When you leave the car, lock it using the remote control.
The next time the driver's door is unlocked with the same remote control and the driver's door is opened, the driver's
seat will automatically move to the position
pg. 69 Interior
Power seats
that it was in when the door was most recently locked with that remote control.
WARNING!
Because the driver's seat can be adjusted with the ignition off, children should never be left unattended in the car.
Movement of the seat can be STOPPED at any time by pressing any button on the power seat control panel.
Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In
addition, position the seat as far rearward as comfort and control allow.
The seat rails on the floor must not be obstructed in any way when the seat is in motion.
pg. 70 Interior
Power retractable hard top
Before raising or lowering the power retractable hard top
Please observe the following information before operating the power retractable hard top:
There should be no objects on the power retractable hard top's cover.
Remove all snow, ice or loose objects from the power retractable hard top and trunk lid.
The top should be dry before it is lowered.
CAUTION!
If the power retractable hard top is lowered while it is wet, water may drip into the passenger compartment or trunk.
There should be at least 6.5 feet (2 meters) of free space from the ground (distance A in the illustration below).
There should be at least 8 inches (20 cm) of free space behind the vehicle (distance B in the illustration below).
The ambient temperature should be above 14°F (-10°C).
ProCarManuals.com
