2006 VOLVO C70 warning

Owners who live in or regularly commute through areas with sustained periods of snow or icy driving conditions are
strongly advised to fit suitable winter tires to help retain the highest degree of traction.
It is important to install winter tires on all four wheels to help retain traction during cornering, braking, and
accelerating. Failure to do so could reduce traction to an unsafe level or adversely affect handling.
Do not mix tires of different design as this could also negatively affect overall tire road grip.
Winter tires wear more quickly on dry roads in warm weather. They should be removed when the winter driving
season has ended.
Studded tires should be run-in 300-600 miles (500-1000 km) during which the car should be driven as smoothly as
possible to give the studs the opportunity to seat properly in the tires. The tires should have the same rotational
direction throughout their entire lifetime.
NOTE: Please consult state or provincial regulations restricting the use of studded winter tires before installing such
tires.
1. Where permitted
pg. 136 Wheels and tires
Wheel nuts
Wheel nuts
There are two different types of wheel nut, depending on whether the wheels are steel or aluminum.
Steel rims - low nut
Steel rims are normally secured using the low type of nut, although steel rims may also use the high type.
WARNING!
Never use the short type of nut for aluminium wheels. This could cause the wheel to come loose.
Aluminum wheels - high nut
Only the high type of nut can be used for aluminum wheels. This is considerably different from other types of nut
because it has a rotating conical thrust washer.
NOTE: This nut can also be used on steel wheels.
Lockable wheel nut
If steel wheels with lockable wheel nuts are used in combination with wheel covers, the lockable wheel nut must be
fitted to the stud nearest the air valve. The wheel cover cannot otherwise be installed on the wheel.
ProCarManuals.com

the car. The use of different size wheels can seriously damage your car's transmission.
Location of the optional spare wheel and tools
The spare wheel is packed in a storage bag and is located under the panel in the floor of the trunk. On cars with a
spare wheel, the jack and lug wrench are secured in a foam plastic block placed in the center of the wheel. The
retaining straps securing the spare wheel is attached to two eyelets in the floor of the spare wheel's storage
compartment.
WARNING!
Current legislation prohibits the use of the "Temporary Spare" tire other than as a temporary replacement for a
punctured tire. It must be replaced as soon as possible by a standard tire. Road holding and handling may be affected
with the "Temporary Spare" in use. Do not exceed 50 mph (80 km/h). Do not drive farther than 50 miles (80 km) on
a temporary spare tire.
Accessing the spare wheel:
Open the hatch in the floor of the trunk.
Release the retaining straps and lift out the spare wheel in its storage bag.
Open the zipper on the storage bag and lift out the spare wheel.
The wheel that was replaced by the temporary spare tire can then be placed in the storage bag.
pg. 139 Wheels and tires
Changing a wheel

Before raising the car:
Engage the parking brake.
Put the gear selector in (P)ark or in reverse if the car is equipped with a manual transmission.
Block the wheels that are on the ground with wooden blocks or large stones.
Remove the wheel cap (where applicable) using the lug wrench.
With the car still on the ground, use the lug wrench to loosen the wheel nuts 1/2-1 turn by exerting downward
pressure. Turn the nuts counterclockwise to loosen.
pg. 140 Wheels and tires
Changing a wheel
ProCarManuals.com

Positioning the jack
There are two jack attachment points on each side of the car.
Position the jack correctly in the attachment (see illustration above) and crank while simultaneously guiding the base
of the jack to the ground. The base of the jack must be flat on a level, firm, non-slippery surface.
Before raising the car, check that the jack is still correctly positioned in the attachment.
WARNING!
The jack must correctly engage the jack attachment.
Be sure the jack is on a firm, level, non-slippery surface.
Never allow any part of your body to be extended under a car supported by a jack.
Use the jack intended for the car when changing a tire. For any other job, use stands to support the car.
Apply the parking brake and put the gear selector in the (P)ark position.
Block the wheels standing on the ground, use rigid wooden blocks or large stones.
The jack should be kept well-greased.
Removing a wheel:
Raise the vehicle until the wheel to be changed is lifted off the ground.
Unscrew the wheel nuts completely and carefully remove the wheel so as not to damage the threads on the studs.
Installing a wheel
Clean the contact surfaces on the wheel and hub.
Lift the wheel and place it on the hub.
Install the wheel nuts and tighten hand -tight. Using the lug wrench, tighten crosswise until all nuts are snug.
Lower the vehicle to the ground and alternately tighten the bolts crosswise to 62 ft. lbs. (85 Nm).
Install the wheel cap (where applicable).
pg. 141 Wheels and tires
Tire sealing system
ProCarManuals.com

Your vehicle is equipped with a tire sealing system that enables you to temporarily seal a hole in the tread surface and
re-inflate a flat tire, or to adjust a tire's inflation pressure.
The tire sealing kit is stowed behind the ski hatch in the center of the rear seat backrest.
The jack, and lug wrench are secured in a foam plastic block located under the floor panel in the trunk.
The system consists of an air compressor, an integrated container for the sealing compound, wiring to connect the
system to the vehicle's electrical system via one of the 12-volt sockets, and a hose used to connect the system to the
tire's inflation valve.
NOTE:
The tire sealing system is only intended to seal holes on the tire's tread area, not the sidewall.
Tires with large holes or tears cannot be repaired with the tire sealing system.
WARNING!
After using the tire sealing system, the vehicle should not be driven farther than approximately 120 miles (200
km). Have the tire replaced as soon as possible.
The vehicle should not be driven faster than 50 mph (80 km/h) while using a tire that has been temporarily
repaired with the tire sealing system.
After using the tire sealing system, drive carefully and avoid abrupt steering maneuvers and sudden stops.
pg. 142 Wheels and tires
Tire sealing system
ProCarManuals.com

Temporarily repairing a flat tire
Before using the tire sealing system, observe the following:
WARNING!
Never leave the tire sealing system unattended when it is operating.
Keep the tire sealing system kit away from children.
The vehicle's engine should be running when the tire sealing system is used to avoid battery drain. Therefore, be
sure the vehicle is parked in a well ventilated place before using the system.
Be sure the vehicle is parked safely off the road and away from moving traffic.
Apply the parking brake.
Do not remove any foreign objects (nails, etc.) from the tire.
Temporarily repairing a flat tire is done in two stages.
In the first stage, the hole is sealed by pumping sealing compound into the tire. The car is then driven a short
distance to distribute the sealing compound in the tire.
In the second stage, the tire's inflation pressure is checked and adjusted if necessary.
Stage 1: Sealing the hole
Peel off the speed limit sticker (1) and affix it to the steering wheel hub where it will be clearly visible to the driver.
Ensure that the orange switch (2) is in position 0 (the 0 side of the switch should be pressed down).
Pull out the electrical wire (5) and hose (4) from the side compartment (3).
Remove the valve cap from the tire's inflation valve and screw the hose connector onto the valve as tightly as
possible by hand.
Connect the electrical wire to the nearest 12-volt socket in the vehicle.
Release the safety catch (6) and turn the orange colored section of the sealing kit (7), which holds the sealing
compound container, 90 degrees until it clicks into the vertical position.
Start the vehicle's engine.
Start the tire sealing system's compressor by pressing the switch (2) to position I.
NOTE: The air pressure gauge (9) will temporarily show an increase in pressure to approximately 88 psi (6 bar) while
the sealing compound is being pumped into the tire. The pressure should return to a normal level after approximately
one minute.
pg. 143 Wheels and tires
Tire sealing system
WARNING!
ProCarManuals.com

Contact with the sealing compound may cause skin irritation. If contact occurs, wash the affected area immediately
with soap and water.
Never stand next to the tire being inflated when the compressor is in operation. If cracks, bubbles, etc. form on the
tire, switch off the compressor immediately. If there is visible damage to the sidewall or the rim, the tire cannot be
repaired. The vehicle should not be driven if this occurs. Contact a towing service or Volvo On Call Roadside
Assistance if applicable.
Within seven minutes, inflate the tire to between 22 - 50 psi (1.8 - 3.5 bar). Switch off the compressor briefly to get a
clear reading from the pressure gauge (9).
CAUTION!
If the pressure remains below 22 psi (1.8 bar) after approximately seven minutes, turn off the compressor. In this
case, the hole is too large to be sealed and the vehicle should not be driven.
Disconnect the electrical wire from the 12-volt socket.
Unscrew the hose from the tire's inflation valve and reinstall the valve cap.
Fold down the orange section of the tire sealing system to its original (horizontal) position and press the safety catch
into place.
Safely stow the tire sealing system kit in a convenient place as it will soon be used again to check the tire's inflation
pressure.
Immediately drive the vehicle for approximately 2 miles (3 km) to distribute the sealing compound in the tire.
WARNING!
If heavy vibrations, unsteady steering behavior, or noises should occur while driving, reduce speed and park the car
in a safe place. Recheck the tire for bumps, cracks, or other visible damage, and recheck its inflation pressure. If the
pressure is below 16 psi (1.3 bar), do not continue driving. Have the vehicle towed to a workshop or Volvo retailer.
Stage 2: Checking inflation pressure
Park the car in a safe place.
Ensure that the orange switch (2) is in position 0 (the 0 side of the switch should be pressed down).
Remove the valve cap from the tire's inflation valve and screw the hose connector onto the valve as tightly as
possible by hand.
Connect the electrical wire to the nearest 12-volt socket in the vehicle.
Start the vehicle's engine.
Check the tire's inflation pressure on the gauge (9).
NOTE: In dark conditions, switching on the tire sealing system's compressor will illuminate the pressure gauge.
Inflate the tire to the correct pressure as indicated in the tire inflation tables on page 116. If the tire needs to be
inflated, start the tire sealing system's compressor. If necessary, release air from the tire by pressing the vent button (8).
Turn off the compressor (press switch 2 to the 0 position) when the correct inflation pressure has been reached.
pg. 144 Wheels and tires
Tire sealing system
CAUTION!
The compressor should not be used for more than ten minutes at a time to avoid overheating.
ProCarManuals.com

Unscrew the hose from the tire's inflation valve and reinstall the valve cap.
Disconnect the electrical wire from the 12-volt socket.
Return the hose and electrical wire to the compartment on the side of the unit.
NOTE: When the tire sealing system has been used to seal a flat tire, the tank containing the sealing compound, and
the hose must be replaced. See the instructions on the following page. Contact a Volvo retailer for replacement parts.
pg. 145 Wheels and tires
Tire sealing system
CAUTION!
If your vehicle is equipped with the optional Tire Pressure Monitoring System (see page 117
), the use of the sealing
compound may lead to incorrect tire pressure readings or in rare cases, damage to the tire pressure sensor. Use the
tire sealing system to check and adjust the damaged tire's pressure.
After use, return the tire sealing system to its storage compartment behind the ski hatch in the center of the rear seat
backrest.
WARNING!
If you interrupt your trip for more than one hour, check the inflation pressure in the damaged tire again before
continuing. See the section "Stage 2: Checking inflation pressure" on page 143
.
Replacing the sealing compound container
The sealing compound container must be replaced if:
the tire sealing system has been used to repair a tire the container's expiration date has passed (see the date on decal
1).
After use, the container (6), its retaining bracket (9), and the hose (10) must be replaced. Please consult your Volvo
retailer for replacement parts.
See also the safety regulations on the bottom of the container.
WARNING!
Be sure that the compressor is not connected to a 12-volt socket while replacing the container.
pg. 146 Wheels and tires
ProCarManuals.com

Automatic washing - simple and quick
We do NOT recommend washing your car in an automatic wash during the first six months (because the paint will
not have hardened sufficiently).
An automatic wash is a simple and quick way to clean your car, but it is worth remembering that it may not be as
thorough as when you yourself go over the car with sponge and water. Keeping the underbody clean is most important,
especially in the winter. Some automatic washers do not have facilities for washing the underbody.
pg. 149 Vehicle care
Washing and cleaning the car
CAUTION!
Before driving into an automatic carwash, turn off the optional rain sensor to avoid damaging the windshield wipers.
Make sure that side view mirrors, auxiliary lamps, etc, are secure, and that any antenna(s) are retracted or removed.
Otherwise there is risk of the machine dislodging them.
WARNING!
When the car is driven immediately after being washed, apply the brakes several times in order to remove any
moisture from the brake linings.
Engine cleaning agents should not be used when the engine is warm. This constitutes a fire risk.
Polishing and Waxing
Normally, polishing is not required during the first year after delivery, however, waxing may be beneficial.
Before applying polish or wax the vehicle must be washed and dried. Tar spots can be removed with kerosene or tar
remover. Difficult spots may require a fine rubbing compound.
After polishing use liquid or paste wax.
Several commercially available products contain both polish and wax.
Waxing alone does not substitute for polishing a dull surface.
A wide range of polymer-based waxes can be purchased today. These waxes are easy to use and produce a long-
lasting, high-gloss finish that protects the bodywork against oxidation, road dirt and fading.
Do not polish or wax your vehicle in direct sunlight (the surface of the vehicle should not be warmer than 113° F
(45° C).
CAUTION!
Volvo does not recommend the use of long-life or durable paint protection coatings, some of which may claim to
prevent pitting, fading, oxidation, etc. These coatings have not been tested by Volvo for compatibility with your
vehicle's clear coat. Some of them may cause the clear coat to soften, crack, or cloud. Damage caused by application
of paint protection coatings may not be covered under your vehicle's paint warranty.
pg. 150 Vehicle care
Washing and cleaning the car
Upholstery care
Fabric
ProCarManuals.com