2006 VOLVO C70 engine

Slide the ball holder into the hitch assembly.
Align the hole in the ball holder with the one in the hitch assembly.
Slide the locking bolt through the hitch assembly/ball holder.
Insert the cotter pin in the hole at the end of the locking bolt.
Removing the ball holder
Remove the cotter pin from the locking bolt and slide the locking bolt out of the ball holder/hitch assembly.
Pull the ball holder out of the hitch assembly.
NOTE: A cover for the hitch assembly is also included in the kit.
pg. 123 Starting and driving
Transporting loads
Loading the car Your vehicle's load-carrying capacity is affected by factors such as:
the number of passengers
tire inflation
the amount of optional or accessory equipment installed
the amount of cargo
See the chapter "Wheels and tires"
for more detailed information.
Before loading the car, turn off the engine, and apply the parking brake when loading or unloading long objects. The
gear selector can be inadvertently knocked out of position by long cargo, causing the car to move.
Keep the following in mind when loading the vehicle:
Load the cargo in the trunk against the rear seat backrest.
Load heavy cargo as low as possible.
Center wide loads.
Secure all cargo with restraining straps anchored to the load securing eyelets.
Cover sharp edges on the load.
WARNING!
Remember that an object weighing 44 lbs (20 kg) produces a force of 2,200 lbs (1,000 kg) in a head-on collision at
30 m.p.h. (50 km/h)!
pg. 124 Starting and driving
This page left intentionally blank.

Contents | Top of Page
ProCarManuals.com

Temporarily repairing a flat tire
Before using the tire sealing system, observe the following:
WARNING!
Never leave the tire sealing system unattended when it is operating.
Keep the tire sealing system kit away from children.
The vehicle's engine should be running when the tire sealing system is used to avoid battery drain. Therefore, be
sure the vehicle is parked in a well ventilated place before using the system.
Be sure the vehicle is parked safely off the road and away from moving traffic.
Apply the parking brake.
Do not remove any foreign objects (nails, etc.) from the tire.
Temporarily repairing a flat tire is done in two stages.
In the first stage, the hole is sealed by pumping sealing compound into the tire. The car is then driven a short
distance to distribute the sealing compound in the tire.
In the second stage, the tire's inflation pressure is checked and adjusted if necessary.
Stage 1: Sealing the hole
Peel off the speed limit sticker (1) and affix it to the steering wheel hub where it will be clearly visible to the driver.
Ensure that the orange switch (2) is in position 0 (the 0 side of the switch should be pressed down).
Pull out the electrical wire (5) and hose (4) from the side compartment (3).
Remove the valve cap from the tire's inflation valve and screw the hose connector onto the valve as tightly as
possible by hand.
Connect the electrical wire to the nearest 12-volt socket in the vehicle.
Release the safety catch (6) and turn the orange colored section of the sealing kit (7), which holds the sealing
compound container, 90 degrees until it clicks into the vertical position.
Start the vehicle's engine.
Start the tire sealing system's compressor by pressing the switch (2) to position I.
NOTE: The air pressure gauge (9) will temporarily show an increase in pressure to approximately 88 psi (6 bar) while
the sealing compound is being pumped into the tire. The pressure should return to a normal level after approximately
one minute.
pg. 143 Wheels and tires
Tire sealing system
WARNING!
ProCarManuals.com

Contact with the sealing compound may cause skin irritation. If contact occurs, wash the affected area immediately
with soap and water.
Never stand next to the tire being inflated when the compressor is in operation. If cracks, bubbles, etc. form on the
tire, switch off the compressor immediately. If there is visible damage to the sidewall or the rim, the tire cannot be
repaired. The vehicle should not be driven if this occurs. Contact a towing service or Volvo On Call Roadside
Assistance if applicable.
Within seven minutes, inflate the tire to between 22 - 50 psi (1.8 - 3.5 bar). Switch off the compressor briefly to get a
clear reading from the pressure gauge (9).
CAUTION!
If the pressure remains below 22 psi (1.8 bar) after approximately seven minutes, turn off the compressor. In this
case, the hole is too large to be sealed and the vehicle should not be driven.
Disconnect the electrical wire from the 12-volt socket.
Unscrew the hose from the tire's inflation valve and reinstall the valve cap.
Fold down the orange section of the tire sealing system to its original (horizontal) position and press the safety catch
into place.
Safely stow the tire sealing system kit in a convenient place as it will soon be used again to check the tire's inflation
pressure.
Immediately drive the vehicle for approximately 2 miles (3 km) to distribute the sealing compound in the tire.
WARNING!
If heavy vibrations, unsteady steering behavior, or noises should occur while driving, reduce speed and park the car
in a safe place. Recheck the tire for bumps, cracks, or other visible damage, and recheck its inflation pressure. If the
pressure is below 16 psi (1.3 bar), do not continue driving. Have the vehicle towed to a workshop or Volvo retailer.
Stage 2: Checking inflation pressure
Park the car in a safe place.
Ensure that the orange switch (2) is in position 0 (the 0 side of the switch should be pressed down).
Remove the valve cap from the tire's inflation valve and screw the hose connector onto the valve as tightly as
possible by hand.
Connect the electrical wire to the nearest 12-volt socket in the vehicle.
Start the vehicle's engine.
Check the tire's inflation pressure on the gauge (9).
NOTE: In dark conditions, switching on the tire sealing system's compressor will illuminate the pressure gauge.
Inflate the tire to the correct pressure as indicated in the tire inflation tables on page 116. If the tire needs to be
inflated, start the tire sealing system's compressor. If necessary, release air from the tire by pressing the vent button (8).
Turn off the compressor (press switch 2 to the 0 position) when the correct inflation pressure has been reached.
pg. 144 Wheels and tires
Tire sealing system
CAUTION!
The compressor should not be used for more than ten minutes at a time to avoid overheating.
ProCarManuals.com

2 0 0 6
VOLVO C70
Chapter 9 - Vehicle care
pg. 147 Vehicle care
Washing and cleaning the car 148
Paint touch up151
pg. 148 Vehicle care
Washing and cleaning the car
Washing the car
The following points should be kept in mind when washing and cleaning the car:
The car should be washed at regular intervals since dirt, dust, insects and tar spots adhere to the paint and may cause
damage. To help prevent corrosion, it is particularly important to wash the car frequently in the wintertime.
Avoid washing your car in direct sunlight. Doing so may cause detergents and wax to dry out and become abrasive.
To avoid scratching, use lukewarm water to soften the dirt before you wash with a soft sponge, and plenty of sudsy
water.
Bird droppings: Remove from paintwork as soon as possible. Otherwise the finish may be permanently damaged.
A detergent can be used to facilitate the softening of dirt and oil.
A water-soluble grease solvent may be used in cases of sticky dirt. However, use a wash place equipped with a
drainage separator.
Dry the car with a clean chamois and remember to clean the drain holes in the doors and rocker panels.
Tar spots can be removed with kerosene or tar remover after the car has been washed.
A stiff-bristle brush and lukewarm soapy water can be used to clean the wiper blades. Frequent cleaning improves
visibility considerably.
Wash off the dirt from the underside (wheel housings, fenders, etc).
In areas of high industrial fallout, more frequent washing is recommended.
After cleaning the engine, the spark plug wells should be inspected for water and blown dry if necessary.
Exterior plastic components
Cleaning exterior plastic components should be done with a cleaning agent specially designed for this purpose.
Solvents or stain removers should not be used. Consult your Volvo retailer.
NOTE: When washing the car, remember to remove dirt from the drain holes in the doors and sills.
CAUTION!
During high pressure washing, the spray mouthpiece must never be closer to the vehicle than 13" (30 cm). Do not
spray into the locks.
When washing or steam cleaning the engine, avoid spraying water or steam directly on the electrical components or
toward the rear side of the engine.
ProCarManuals.com

Automatic washing - simple and quick
We do NOT recommend washing your car in an automatic wash during the first six months (because the paint will
not have hardened sufficiently).
An automatic wash is a simple and quick way to clean your car, but it is worth remembering that it may not be as
thorough as when you yourself go over the car with sponge and water. Keeping the underbody clean is most important,
especially in the winter. Some automatic washers do not have facilities for washing the underbody.
pg. 149 Vehicle care
Washing and cleaning the car
CAUTION!
Before driving into an automatic carwash, turn off the optional rain sensor to avoid damaging the windshield wipers.
Make sure that side view mirrors, auxiliary lamps, etc, are secure, and that any antenna(s) are retracted or removed.
Otherwise there is risk of the machine dislodging them.
WARNING!
When the car is driven immediately after being washed, apply the brakes several times in order to remove any
moisture from the brake linings.
Engine cleaning agents should not be used when the engine is warm. This constitutes a fire risk.
Polishing and Waxing
Normally, polishing is not required during the first year after delivery, however, waxing may be beneficial.
Before applying polish or wax the vehicle must be washed and dried. Tar spots can be removed with kerosene or tar
remover. Difficult spots may require a fine rubbing compound.
After polishing use liquid or paste wax.
Several commercially available products contain both polish and wax.
Waxing alone does not substitute for polishing a dull surface.
A wide range of polymer-based waxes can be purchased today. These waxes are easy to use and produce a long-
lasting, high-gloss finish that protects the bodywork against oxidation, road dirt and fading.
Do not polish or wax your vehicle in direct sunlight (the surface of the vehicle should not be warmer than 113° F
(45° C).
CAUTION!
Volvo does not recommend the use of long-life or durable paint protection coatings, some of which may claim to
prevent pitting, fading, oxidation, etc. These coatings have not been tested by Volvo for compatibility with your
vehicle's clear coat. Some of them may cause the clear coat to soften, crack, or cloud. Damage caused by application
of paint protection coatings may not be covered under your vehicle's paint warranty.
pg. 150 Vehicle care
Washing and cleaning the car
Upholstery care
Fabric
ProCarManuals.com

2 0 0 6
VOLVO C70
Chapter 10 - Maintenance and servicing
pg. 153 Maintenance and servicing
Volvo maintenance 154
Maintaining your car155
Hood and engine compartment157
Engine oil158
Fluids159
Wiper blades161
Battery162
Bulbs164
Replacing front bulbs165
Replacing bulbs in the trunk168
Replacing interior bulbs169
Fuses170
pg. 154 Maintenance and servicing
Volvo maintenance
Volvo advises you to follow the maintenance program outlined in the Warranty and Service Records Information
booklet. This maintenance program contains inspections and services necessary for the proper function of your vehicle.
The maintenance services contain several checks that require special tools and training, and therefore must be
performed by a qualified technician. To keep your Volvo in top condition, specify time-tested and proven Genuine
Volvo Parts and Accessories.
The Federal Clean Air Act - U.S
The Federal Clean Air Act requires vehicle manufacturers to furnish written instructions to the ultimate purchaser to
assure the proper servicing and function of the components that control emissions. These services, which are listed in
the "Warranty and Service Records Information" booklet, are not covered by the warranty. You will be required to pay
for labor and material used.
Maintenance
Your Volvo passed several major inspections before it was delivered to you, in accordance with Volvo specifications.
The maintenance procedures outlined in the Warranty and Service Records Information booklet, many of which will
positively affect your vehicle's emissions, should be performed as indicated. It is recommended that receipts for
vehicle emission maintenance be retained in case questions arise concerning maintenance. Inspection and maintenance
should also be performed anytime a malfunction is observed or suspected.
Applicable warranties - U.S/ Canada
ProCarManuals.com

In accordance with applicable U.S. and Canadian regulations, the following list of warranties is provided.
New Vehicle Limited Warranty
Parts and Accessories Limited Warranty
Corrosion Protection Limited Warranty
Seat Belt and Supplemental Restraint Systems Limited Warranty
Emission Design and Defect Warranty
Emission Performance Warranty
These are the federal warranties; other warranties are provided as required by state/ provincial law. Refer to your
separate Warranty and Service Records Information booklet for detailed information concerning each of the warranties.
Periodic maintenance helps minimize emissions
Periodic maintenance will help keep your vehicle running well. Your Warranty and Service Records Information
booklet provides a comprehensive periodic maintenance schedule up to 150,000 miles (240,000 km) of vehicle
maintenance. The schedule includes components that affect vehicle emissions. This page describes some of the
emission-related components.
Vehicle Event Data (Black Box)
Your vehicle's driving and safety systems employ computers that monitor, and share with each other, information
about your vehicle's operation. One or more of these computers may store what they monitor, either during normal
vehicle operation or in a crash or near-crash event. Stored information may be read and used by:
Volvo Car Corporation
service and repair facilities
law enforcement or government agencies
others who may assert a legal right to know, or who obtain your consent to know such information.
pg. 155 Maintenance and servicing
Maintaining your car
Owner maintenance
Periodic maintenance requirements and intervals are described in your vehicle's Warranty and Service Records
Information booklet.
The following points can be carried out between the normally scheduled maintenance services.
Each time the car is refueled:
Check the engine oil level
Clean the windshield, windshield wipers, headlights, and tail lights
Monthly:
Check cold tire pressure in all tires. Inspect the tires for wear.
Check that engine coolant and other fluid levels are between the indicated "min" and "max" markings.
Clean interior glass surfaces with a glass cleaner and soft paper towels.
Wipe driver information displays with a soft cloth.
Visually inspect battery terminals for corrosion. Corrosion may indicate a loose terminal connector, or a battery near
the end of its useful service life. Consult your Volvo retailer for additional information.
As needed:
Wash the car, including the undercarriage, to reduce wear that can be caused by a buildup of dirt, and corrosion that
can be caused by salt residues.
ProCarManuals.com

Clean leaves and twigs from air intake vents at the base of the windshield, and from other places where they may
collect.
NOTE: Complete service information for qualified technicians is available online for purchase or subscription at
www.volvotechinfo.com
.
pg. 156 Maintenance and servicing
Maintaining your car
Emission inspection readiness What is an Onboard Diagnostic System (OBD II)?
OBD II is part of your vehicle's computerized engine management system. It stores diagnostic information about your
vehicle's emission controls. It can light the Check Engine light (MIL) if it detects an emission control "fault." A "fault"
is a component or system that is not performing within an expected range. A fault may be permanent or temporary.
OBD II will store a message about any fault.
How do states use OBD II for emission inspections?
Many states connect a computer directly to a vehicle's OBD II system. The inspector can then read "faults." In some
states, this type of inspection has replaced the tailpipe emission test.
How can my vehicle fail OBD II emission inspection?
Your vehicle can fail OBD II emission inspection for any of the following reasons.
If your Check Engine (MIL) light is lit, your vehicle may fail inspection.
If your vehicle's Check Engine light was lit, but went out without any action on your part, OBD II will still have a
recorded fault. Your vehicle may pass or fail, depending on the inspection practices in your area.
If you had recent service that required disconnecting the battery, OBD II diagnostic information may be incomplete
and "not ready" for inspection. A vehicle that is not ready may fail inspection.
How can I prepare for my next OBD II emission inspection?
If your Check Engine (MIL) light is lit - or was lit but went out without service, have your vehicle diagnosed and, if
necessary, serviced by a qualified Volvo technician.
If you recently had service for a lit Check Engine light, or if you had service that required disconnecting the battery,
a period of driving is necessary to bring the OBD II system to "ready" for inspection. A half-hour trip of mixed stop-
and -go/ highway driving is typically needed to allow OBD II to reach readiness. Your Volvo retailer can provide you
with more information on planning a trip.
Maintain your vehicle in accordance with your vehicle's maintenance schedule.
pg. 157 Maintenance and servicing
Hood and engine compartment
ProCarManuals.com