2006 TOYOTA xA trunk release
[x] Cancel search: trunk releasePage 5 of 23
PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4
SCION
SCION
Page 17
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Press and
releaseboth
LOCK and
UNLOCK
buttons at the
same time.
b. Press and
releasethe
UNLOCK button
once for all
doors unlock.
or Press and
releasethe
LOCK button
once for driver’s
door unlock.e.Open the driver’s
door;
programming is
now complete.
i.The tail and marker lights flash 1time, the
buzzer chirps 1time, and the doors lock and
unlock 1 time.
The xA Security with RKE will arm 30 seconds after the LOCK button on
the remote control is pressed, and DISARM when the UNLOCK button is
pressed. When the LOCK button is pressed, all the vehicle’s doors lock.
When the UNLOCK button is pressed, the driver’s door unlocks*, but if the
UNLOCK button is pressed again within 3 seconds, the remaining doors
unlock.
The xA Security with RKE will automatically RELOCK the vehicle’s doors if
no door is opened within 30 seconds after REMOTE DISARMING, the will
REARM 30 seconds later.
The xA Security with RKE will arm 30 seconds after you close and lock
the vehicle’s doors with the key, and will DISARM when you unlock a door
with the key.
The xA Security with RKE may be programmed to automatically arm 30
seconds after the ignition key is removed, the vehicle exited and the last
door and the trunk are closed, without the necessity of locking the doors.
The xA Security with RKE may be DISARMED with the vehicle’s ignition
key after it was PASSIVELY ARMED.
When the xA Security with RKE has been PASSIVELY ARMED, and
ENTRY DELAY (user-selectable at 0,15, or 30 seconds) will start when a
door is opened before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the xA Security with RKE will rm 30 seconds after you close all the doors
and the hatch (if open).
The xA Security with RKE may be DISARMED by inserting the key into
the ignition switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the xA Security with
RKE is ARMED will TRIGGER and ALARM immediately**. (If the system
was PASSIVELY ARMED, the ENTRY DELAY must pass before the
ALARM is TRIGGERED).
The xA-Security utilizes RADAR SENSOR.
The RADAR SENSOR works synchronize with vehicle theft deterrent sys-
tem.If somebody intrudes into the vehicle while the vehicle theft deterrent
system is set, the alarm blows the vehicle's horn intermittently and flashes
the emergency flashers.
Note
To prevent false alarms from triggered in case of following conditions:
•A child or pet is left in the vehicle.
•Any window or moon roof is left opened.
•When parking in the noisy area or in the roof parking.
•The vehicle body or glass is subjected to strong impact from the outside
(such as highly pressurized car wash).
•When transporting by car carrier.
•A cellphone in cup holder or center console covered storage is left in the
vehicle.
•When a bag on the seat in the vehicle,the detection area may change.
While ARMED, the xA Security with RKE monitors the ignition switch. If an
attempt is made to start the vehicle without a key, an ALARM is triggered. REMOTE ARMING /
DISARMING & LOCK-
ING / UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
RADAR SENSOR
IGNITION SWITCH
MONITORING
FEATURES FUNCTIONS* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.
Page 7 of 23
PROGRAMMINGPASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTIONThe xA Security with RKE is factory-set to not P
ASSIVELY
ARM. To change the system’s operation for
P
ASSIVE
ARMING
operation, as well as adjust the E
NTRY
DELAY
time, follow the procedure below. For
more information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure.(Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATIONARMING THE xA SECURITY WITH RKE (except PASSIVE ARMING)The system may be A
RMED
in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
* The system will not A
RM
while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6
SCION
SCION
Page 15
SCIONSECURITYTURN TOWARD THE FRONT
OF THE VEHICLEPRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR30 SECONDS(PRE-ARM
-
ING)THEN
FLASHES(SYSTEM IS
ARMED
)
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times.b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.a. Close, then Open the door:
2 times = P
ASSIVE
ARMING
OFF
3 times = P
ASSIVE
ARMING
ON,
0 Sec. E
NTRY
DELAY
4 times = P
ASSIVE
ARMING
ON,
15 Sec. E
NTRY
DELAY
5 times = P
ASSIVE
ARMING
ON,
30 Sec. E
NTRY
DELAY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete. e. Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS
REMOTE ARMED
1
2
31112
3
3
Page 10 of 23
OPERATIONAUTOMATIC REARMINGWhen you unlock the doors using the remote control, the xA Security with RKE is D
ISARMED
at the
same time. However, if you do not open a door within 30 seconds, the system will relock the doors
and the xA Security with RKE will R
EARM
30 seconds later.
0
15
30 45
Page 12
SCION
SCION
Page 9
THE DOORS ARE
UNLOCKED BY PRESSING
THE UNLOCK BUTTON ON
THE REMOTE CONTROL
...
WHEN NO DOOR OR
HATCH IS OPENED
...
FOR MORE THAN
30
SECONDS
...
THE X
A SECURITY WITHRKE
AUTOMATICALLY RELOCKS
THE DOORS
, THEN
AUTOMATICALLY REARMS
.
THE LED LIGHTS UP
FOR
30 SECONDS
(PRE-ARM
), THEN
FLASHES WHEN THE
SYSTEM IS ARMED
ALARM INFORMATIONALARM TRIGGERSWhile the system is A
RMED
, an A
LARM
will be T
RIGGERED
when any of the following occurs:
Forcibly opening a door or hatch without a key.
Opening the passenger side door or hatch with a key, while armed,
will trigger the alarm.
Pulling the trunk or hatch release lever inside the vehicle will
also T
RIGGER
an A
LARM
.
Manually unlocking a door
Manually operating an inside lock button will T
RIGGER
an A
LARM
.
Note: Because this action will T
RIGGER
an A
LARM
, it is
important that you do not A
RM
the system while
someone is in the vehicle.
“Hot wiring” the vehicle
The xA Security with RKE can detect the absence of the ignition key
if the ignition circuit is shorted in attempt to start the vehicle.
Intrusion Detection
When the radar sensor detects intrusion, it TRIGGERS an ALARM
first, then a regular ALARM. See the description of how the RADAR
SENSOR TRIGGERS ALARMS on page 14.
Power restoration
If power to the system is interrupted while it is A
RMED
, an A
LARM
will
be T
RIGGERED
immediately when power is restored.
SCIONSECURITY
Page 11 of 23
ALARM INFORMATIONPANIC MODE OPERATIONWhen you are confronted by a threatening situation, you may call attention to your vehicle by press-
ing the PANIC button on the back of the remote control. Unless you D
ISARM
the P
ANIC
ALARM
by
one of the described methods, it will continue for 60 seconds, then stop.
To activate the P
ANIC
ALARM
:
Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANIC
ALARM
at any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARM
TRIGGER
during the P
ANIC
ALARM
, the
regular A
LARM
takes over. See ALARM INFORMATION on pages 12 and 13 for additional informa-
tion.
PANIC
Page 10
SCION
SCION
Page 11
MISCELLANEOUSDOOR AJAR WARNINGThe xA Security with RKE will sound a five second D
OOR
AJAR
WARNING
when you attempt to
R
EMOTE
ARM
the system while a door is open. To stop the warning tone, either close the open door,
or press and release the UNLOCK button on the remote control. To A
RM
the system, press the
LOCK button again.
Note: The D
OOR
AJAR
WARNING
will not sound when the hatch is open; the doors will lock,
but the system will not ARM
until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKINGThe xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or
“LOCK”. If you start the vehicle while a door is open, the system will not lock the doors; you must
lock them manually.
How the xA Security with RKE automatically locks and unlocks the doors:
This feature may be defeated by changing the system’s programming. Refer to page 18 for pro-
gramming instructions.REMOTE CONTROL RANGEThe maximum range for the xA Security with RKE’s remote controls is 50 feet. However, several
factors that may affect your remote control’s actual performance, include, but are not limited to:
The remote control’s battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the system’s antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
*As the REMOTE CONTROL’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.WITH ALL THE DOORS
CLOSED
, TURN THE KEY TO
THE“ON”
OR“LOCK”
POSITION
...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY
.
WHEN THE KEY IS TURNED
BACK TO THE
“ACC”
OR
“LOCK”
POSITION
...
ALL THE DOORS ARE
UNLOCKED
.
THE HORN SOUNDS
FOR
60 SECONDS
HEADLIGHTS FLASH
FOR
60 SECONDS
MARKER LIGHTS
FLASH
FOR
60 SECONDS
TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR
60 SECONDS
1
1
1
1
1
PRESS THE
LOCK BUTTON
ON THE REMOTE
CONTROL
,
OR...
PRESS THE
PANIC BUTTON
AGAIN
, OR...
PRESS THE
UNLOCK
BUTTON ON
THE REMOTE
CONTROL
, OR...
LOCK THE DOORS
WITH THE KEY
, OR...
UNLOCK A DOOR OR THE
TRUNK
WITH THE KEY
Page 12 of 23
ALARM INFORMATIONPANIC MODE OPERATIONWhen you are confronted by a threatening situation, you may call attention to your vehicle by press-
ing the PANIC button on the back of the remote control. Unless you D
ISARM
the P
ANIC
ALARM
by
one of the described methods, it will continue for 60 seconds, then stop.
To activate the P
ANIC
ALARM
:
Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANIC
ALARM
at any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARM
TRIGGER
during the P
ANIC
ALARM
, the
regular A
LARM
takes over. See ALARM INFORMATION on pages 12 and 13 for additional informa-
tion.
PANIC
Page 10
SCION
SCION
Page 11
MISCELLANEOUSDOOR AJAR WARNINGThe xA Security with RKE will sound a five second D
OOR
AJAR
WARNING
when you attempt to
R
EMOTE
ARM
the system while a door is open. To stop the warning tone, either close the open door,
or press and release the UNLOCK button on the remote control. To A
RM
the system, press the
LOCK button again.
Note: The D
OOR
AJAR
WARNING
will not sound when the hatch is open; the doors will lock,
but the system will not ARM
until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKINGThe xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or
“LOCK”. If you start the vehicle while a door is open, the system will not lock the doors; you must
lock them manually.
How the xA Security with RKE automatically locks and unlocks the doors:
This feature may be defeated by changing the system’s programming. Refer to page 18 for pro-
gramming instructions.REMOTE CONTROL RANGEThe maximum range for the xA Security with RKE’s remote controls is 50 feet. However, several
factors that may affect your remote control’s actual performance, include, but are not limited to:
The remote control’s battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the system’s antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
*As the REMOTE CONTROL’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.WITH ALL THE DOORS
CLOSED
, TURN THE KEY TO
THE“ON”
OR“LOCK”
POSITION
...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY
.
WHEN THE KEY IS TURNED
BACK TO THE
“ACC”
OR
“LOCK”
POSITION
...
ALL THE DOORS ARE
UNLOCKED
.
THE HORN SOUNDS
FOR
60 SECONDS
HEADLIGHTS FLASH
FOR
60 SECONDS
MARKER LIGHTS
FLASH
FOR
60 SECONDS
TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR
60 SECONDS
1
1
1
1
1
PRESS THE
LOCK BUTTON
ON THE REMOTE
CONTROL
,
OR...
PRESS THE
PANIC BUTTON
AGAIN
, OR...
PRESS THE
UNLOCK
BUTTON ON
THE REMOTE
CONTROL
, OR...
LOCK THE DOORS
WITH THE KEY
, OR...
UNLOCK A DOOR OR THE
TRUNK
WITH THE KEY
Page 13 of 23
OPERATIONAUTOMATIC REARMINGWhen you unlock the doors using the remote control, the xA Security with RKE is D
ISARMED
at the
same time. However, if you do not open a door within 30 seconds, the system will relock the doors
and the xA Security with RKE will R
EARM
30 seconds later.
0
15
30 45
Page 12
SCION
SCION
Page 9
THE DOORS ARE
UNLOCKED BY PRESSING
THE UNLOCK BUTTON ON
THE REMOTE CONTROL
...
WHEN NO DOOR OR
HATCH IS OPENED
...
FOR MORE THAN
30
SECONDS
...
THE X
A SECURITY WITHRKE
AUTOMATICALLY RELOCKS
THE DOORS
, THEN
AUTOMATICALLY REARMS
.
THE LED LIGHTS UP
FOR
30 SECONDS
(PRE-ARM
), THEN
FLASHES WHEN THE
SYSTEM IS ARMED
ALARM INFORMATIONALARM TRIGGERSWhile the system is A
RMED
, an A
LARM
will be T
RIGGERED
when any of the following occurs:
Forcibly opening a door or hatch without a key.
Opening the passenger side door or hatch with a key, while armed,
will trigger the alarm.
Pulling the trunk or hatch release lever inside the vehicle will
also T
RIGGER
an A
LARM
.
Manually unlocking a door
Manually operating an inside lock button will T
RIGGER
an A
LARM
.
Note: Because this action will T
RIGGER
an A
LARM
, it is
important that you do not A
RM
the system while
someone is in the vehicle.
“Hot wiring” the vehicle
The xA Security with RKE can detect the absence of the ignition key
if the ignition circuit is shorted in attempt to start the vehicle.
Intrusion Detection
When the radar sensor detects intrusion, it TRIGGERS an ALARM
first, then a regular ALARM. See the description of how the RADAR
SENSOR TRIGGERS ALARMS on page 14.
Power restoration
If power to the system is interrupted while it is A
RMED
, an A
LARM
will
be T
RIGGERED
immediately when power is restored.
SCIONSECURITY
Page 16 of 23
PROGRAMMINGPASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTIONThe xA Security with RKE is factory-set to not P
ASSIVELY
ARM. To change the system’s operation for
P
ASSIVE
ARMING
operation, as well as adjust the E
NTRY
DELAY
time, follow the procedure below. For
more information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure.(Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
OPERATIONARMING THE xA SECURITY WITH RKE (except PASSIVE ARMING)The system may be A
RMED
in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.* Then:
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
The vehicle’s tail and marker lights flash once.
The buzzer chirps once.
The S
TATUS
MONITOR
’SLED turns on for 30 seconds, then
starts flashing. The system is now A
RMED
.
* The system will not A
RM
while any of the doors or hatch are open.
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
Page 6
SCION
SCION
Page 15
SCIONSECURITYTURN TOWARD THE FRONT
OF THE VEHICLEPRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR30 SECONDS(PRE-ARM
-
ING)THEN
FLASHES(SYSTEM IS
ARMED
)
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
a. Using the remote control,
lock, then unlock the
doors 3 times.b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button 1 time.a. Close, then Open the door:
2 times = P
ASSIVE
ARMING
OFF
3 times = P
ASSIVE
ARMING
ON,
0 Sec. E
NTRY
DELAY
4 times = P
ASSIVE
ARMING
ON,
15 Sec. E
NTRY
DELAY
5 times = P
ASSIVE
ARMING
ON,
30 Sec. E
NTRY
DELAY
c. Lock, then unlock the
driver’s door inside lock
button 3 times.
d.The system locks the door
in 2 seconds; if this does
not happen, start over.
c.The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete. e. Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS
REMOTE ARMED
1
2
31112
3
3
Page 18 of 23
PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4
SCION
SCION
Page 17
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Press and
releaseboth
LOCK and
UNLOCK
buttons at the
same time.
b. Press and
releasethe
UNLOCK button
once for all
doors unlock.
or Press and
releasethe
LOCK button
once for driver’s
door unlock.e.Open the driver’s
door;
programming is
now complete.
i.The tail and marker lights flash 1time, the
buzzer chirps 1time, and the doors lock and
unlock 1 time.
The xA Security with RKE will arm 30 seconds after the LOCK button on
the remote control is pressed, and DISARM when the UNLOCK button is
pressed. When the LOCK button is pressed, all the vehicle’s doors lock.
When the UNLOCK button is pressed, the driver’s door unlocks*, but if the
UNLOCK button is pressed again within 3 seconds, the remaining doors
unlock.
The xA Security with RKE will automatically RELOCK the vehicle’s doors if
no door is opened within 30 seconds after REMOTE DISARMING, the will
REARM 30 seconds later.
The xA Security with RKE will arm 30 seconds after you close and lock
the vehicle’s doors with the key, and will DISARM when you unlock a door
with the key.
The xA Security with RKE may be programmed to automatically arm 30
seconds after the ignition key is removed, the vehicle exited and the last
door and the trunk are closed, without the necessity of locking the doors.
The xA Security with RKE may be DISARMED with the vehicle’s ignition
key after it was PASSIVELY ARMED.
When the xA Security with RKE has been PASSIVELY ARMED, and
ENTRY DELAY (user-selectable at 0,15, or 30 seconds) will start when a
door is opened before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the xA Security with RKE will rm 30 seconds after you close all the doors
and the hatch (if open).
The xA Security with RKE may be DISARMED by inserting the key into
the ignition switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the xA Security with
RKE is ARMED will TRIGGER and ALARM immediately**. (If the system
was PASSIVELY ARMED, the ENTRY DELAY must pass before the
ALARM is TRIGGERED).
The xA-Security utilizes RADAR SENSOR.
The RADAR SENSOR works synchronize with vehicle theft deterrent sys-
tem.If somebody intrudes into the vehicle while the vehicle theft deterrent
system is set, the alarm blows the vehicle's horn intermittently and flashes
the emergency flashers.
Note
To prevent false alarms from triggered in case of following conditions:
•A child or pet is left in the vehicle.
•Any window or moon roof is left opened.
•When parking in the noisy area or in the roof parking.
•The vehicle body or glass is subjected to strong impact from the outside
(such as highly pressurized car wash).
•When transporting by car carrier.
•A cellphone in cup holder or center console covered storage is left in the
vehicle.
•When a bag on the seat in the vehicle,the detection area may change.
While ARMED, the xA Security with RKE monitors the ignition switch. If an
attempt is made to start the vehicle without a key, an ALARM is triggered. REMOTE ARMING /
DISARMING & LOCK-
ING / UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
RADAR SENSOR
IGNITION SWITCH
MONITORING
FEATURES FUNCTIONS* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.