’06 HIGHLANDER HB_U (L/O 0503)
158
2006 HIGHLANDER (Hybrid) from Mar. ’05 Prod. (OM48530U)
(a)
These messages are to remind the driv-
er if any of the doors are open.
If any of the doors are open with the
ignition on, any one of the messages ap-
pears and the open door warning light
comes on. The message specifies the
door that is open. When the vehicle speed
exceeds 5 km/h (3 mph), the master
warning light flashes and a warning tone
sounds.
If any one of the messages appears,
stop the vehicle and close the door se-
curely. (b)
This message is to remind the driver
that the parking brake is not released.
When the vehicle speed exceeds 5 km/h
(3 mph), the message appears, the master
warning light flashes and a warning tone
sounds.
If the message appears, stop the ve-
hicle and release the parking brake.
(c)
(U.S.A. only)
This message is to remind the driver to
change the engine oil. The message is
a prior notice.
If the driving range after the previous oil
change reaches 7200 km (4500 miles), the
message appears for 15 seconds with the
master warning light and warning tone
when the ignition is on. If the message appears, we recommend
that you change the engine oil at the
earliest opportunity depending on the
driving and road conditions.
The system must be reset after the en-
gine oil change. See following “Resetting
the system” of (d) “MAINT REQD” for the
procedure to reset the system.
(d)
(U.S.A. only)
This message is to remind the driver to
change the engine oil.
If the driving range after the previous oil
change reaches to 8000 km (5000 miles),
the message appears with the master
warning light and warning tone when the
ignition is on. The message stays on with
the ignition on.
If the message appears, change the en-
gine oil as soon as possible.
The system must be reset after the en-
gine oil change. See “Resetting the sys-
tem” below for the procedure to reset the
system.
’06 HIGHLANDER HB_U (L/O 0503)
159
2006 HIGHLANDER (Hybrid) from Mar. ’05 Prod. (OM48530U)
Resetting the system
The system must be reset after the en-
gine oil replacement. Reset the system
by the following procedure.
1. Turn the ignition key to the “LOCK” position with the odometer reading
shown.
For details, see “—Odometer and two trip
meters” on page 154 in this Section. 2. Turn the ignition key to the “ON” posi- tion while holding down the trip meter
reset knob. A message “MAINT REQD
RESET MODE” will appear on the dis-
play.
3. Hold down the knob at least 5 sec- onds. A message “COMPLETE” will ap-
pear and a beep will sound.
(e)
This message is to remind the driver
that the washer fluid level is low.
If the washer fluid level is low, the mes-
sage appears with the master warning
light and warning tone when the ignition
is on. If the message appears, fill the washer
tank as soon as possible. For instruc-
tions, see “Adding washer fluid” on
page 403 in Section 7 3.
(f)
This message is to warn the driver that
the vehicle stability control (VSC) func-
tion of the vehicle dynamics integrated
management (VDIM) is malfunctioning.
If a malfunction is detected, the message
appears with the master warning light and
warning tone when the ignition is on.
If the message appears, the functions
of VDIM listed below may not work pro-
perly. Have the vehicle checked by a
Toyota dealer as soon as possible.
Traction control function
Vehicle stability control function
(g)
This message is to warn the driver that
the engine oil pressure is too low.
If the engine oil pressure is too low, the
message appears with the master warning
light and warning tone when the ignition
is on.
If the message appears, turn the hybrid
system off as soon as possible and
contact a Toyota dealer.
(h)
This message is to warn the driver that
the hybrid system is almost overheat-
ing.
If the coolant temperature is too high, the
message appears with the master warning
light and warning tone when the ignition
is on.
