2006 SUZUKI SX4 terminal

Downloaded from www.Manualslib.com manuals search engine 1A-168 Engine General Information and Diagnosis:
Troubleshooting
Step Action Yes No
1DTC Check
1) Turn ignition switch to OFF position.
2) Connect scan tool to DLC.
3) Check DTC in the following control modules.
•ECM
•TCM
•BCM
• Keyless start control module
• 4WD control module
Is there any DTC other than CAN-DTC?Go to applicable
troubleshooting of DTC
other than CAN-DTC.Go to Step 2.
2Control module connector check
1) Turn ignition switch to OFF position.
2) Be sure to disconnect scan tool from DLC.
3) Disconnect all the following control module connectors.
• Control modules communicated by CAN
–ECM
–TCM
– ABS control module
–BCM
– Combination meter
– Keyless start control module
– 4WD control module
4) Check for proper connection to terminal of each CAN
line of all control module (communicated by CAN)
connectors.
5) If OK, connect all connectors of control module
communicated by CAN securely.
6) Recheck DTC for all control modules communicated by
CAN.
Is there any CAN-DTC?Go to Step 3. Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.

Downloaded from www.Manualslib.com manuals search engine 1A-170 Engine General Information and Diagnosis:
6Terminating resistance check in ECM and combination
meter
1) Turn ignition switch to OFF position and then disconnect
negative (–) cable at battery.
2) Measure resistance between CAN High terminal (2) and
CAN Low terminal (3) on DLC (1).
If resistance 57 – 67
Ω?Go to Step 7. Go to Step 8.
7Substitute ECM and recheck
1) Substitute a known-good ECM and recheck.
Is it in good condition?End. Substitute a known-
good combination meter
and recheck. If NG, go
to Step 11.
8Terminating resistance check in ECM
1) Make sure that ignition switch is OFF position and
battery negative (–) cable is disconnected.
2) Disconnect combination meter connector.
3) Measure resistance between CAN high terminal and
CAN low terminal on DLC as the same manner as Step
6.
Is resistance 114 – 134
Ω?Substitute a known-
good combination
meter.Go to Step 9.
9Internal circuit check in BCM
1) Make sure that ignition switch is OFF position and
battery negative (–) cable is disconnected.
2) Disconnect ABS control module connector.
3) Measure resistance between the followings
• Between CAN high terminal on DLC and “E08-2”
terminal on ABS control module connector
• Between CAN low terminal on DLC and “E08-13”
terminal on ABS control module connector
Is each resistance 0 – 1
Ω?Go to Step 10. Substitute a known-
good BCM.
10Internal circuit check in ABS control module
1) Make sure that ignition switch is OFF position and
battery negative (–) cable is disconnected.
2) Connect ABS control module connector and disconnect
ECM connector.
3) Measure resistance between the followings
• Between CAN High terminal on DLC and “E01-3”
terminal on ECM connector
• Between CAN Low terminal on DLC and “E01-18”
terminal on ECM connector
If each resistance 0 – 1
Ω?Substitute a known-
good ECM and recheck.
If NG, go to step 11.Substitute a known-
good ABS control
module.
11Substitute BCM and recheck
1) Substitute a known-good BCM and recheck.
Is it in good condition?End. Substitute a known-
good ABS control
module. Step Action Yes No
2
1
9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
3
I7RW01110098-01

Downloaded from www.Manualslib.com manuals search engine 1A-172 Engine General Information and Diagnosis:
Inspection of ECM and Its CircuitsS6RW0D1104072
ECM and its circuits can be checked by measuring voltage, pulse signal and resistance with special tool connected.
CAUTION!
ECM cannot be checked by itself. It is strictly prohibited to connect voltmeter or ohmmeter to ECM
with ECM connectors disconnected from it.

Voltage Check
1) Remove ECM (1) from its bracket referring to “Engine Control Module (ECM) Removal and Installation in Section
1C”.
2) Connect special tool between ECM and ECM connectors securely.
Special tool
(A): 09933–06320
3) Check voltage and/or pulse signal using voltmeter (2) and oscilloscope (3).
NOTE
• As each terminal voltage is affected by battery voltage, confirm that it is 11 V or more when ignition
switch is turned ON.
• Voltage with asterisk (*) cannot be measured with voltmeter because it is pulse signal. Use
oscilloscope for its check if necessary.
• Before this inspection, be sure to read the “Precautions of ECM Circuit Inspection”.

Viewed from harness side
1
2
3(A)
I5JB0A110073-01
E01C01
3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238 3 4
18 19 5 6 7 10 11
17 20
47 46 49 50 51 21 22
5216 259
24 14
29
55 57 54 53 59
60 582
26 27 28 15
30
56 4832 31 34 35 36 37 40 42 39 38 44
45 43 41 331 12 13
238
I6RW0D110051-01

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-173
Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks
C01-1BLU/
YELFuel injector No.1
output10 – 14 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
10 – 14 V
(“Reference
waveform No.1: ”,
“Reference waveform
No.2: ” and
“Reference waveform
No.28: ”)Engine running at idle
after warmed up engine.Output signal is active low
pulse. Pulse frequency
varies depending on
engine speed.
C01-2BLU/
WHTFuel injector No.2
output10 – 14 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
10 – 14 V
(“Reference
waveform No.1: ” and
“Reference waveform
No.3: ”)Engine running at idle
after warmed up engine.Output signal is active low
pulse. Pulse frequency
varies depending on
engine speed.
C01-3GRN/
ORNEGR valve
(stepper motor coil
2) output (if
equipped)10 – 14 V Ignition switch turned ON. —
*0 – 1 V
↑↓
10 – 14 V
(“Reference
waveform No.4: ”)Ignition switch is turned to
ST (cranking) position.Output signal is active low
duty pulse. Number of
pulse generated times
varies depending on
vehicle condition.
C01-4GRN/
REDEGR valve
(stepper motor coil
1) output (if
equipped)10 – 14 V Ignition switch turned ON. —
*0 – 1 V
↑↓
10 – 14 V
(“Reference
waveform No.4: ”)Ignition switch is turned to
ST (cranking) position.Output signal is active low
duty pulse. Number of
pulse generated times
varies depending on
vehicle condition.
C01-5GRN/
WHTIgnition coil No.2
and No.3 output0 – 0.6 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
3 – 5 V
(“Reference
waveform No.5: ” and
“Reference waveform
No.6: ”)Engine running at idle
after warmed up engine.Output signal is active
high pulse. Pulse
frequency varies
depending on engine
speed.
C01-6GRN/
YELIgnition coil No.1
and No.4 output0 – 0.6 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
3 – 5 V
(“Reference
waveform No.6: ”,
“Reference waveform
No.7: ” and
“Reference waveform
No.28: ”)Engine running at idle
after warmed up engine.Output signal is active
high pulse. Pulse
frequency varies
depending on engine
speed.
C01-7 — — — — —
C01-8 — — — — —
C01-9 — — — — —

Downloaded from www.Manualslib.com manuals search engine 1A-174 Engine General Information and Diagnosis:
C01-10 WHTOxygen signal of
heated oxygen
sensor-10 – 1 V Ignition switch turned ON.
— *Deflects between
over 0.5 V and under
0.45 V
(“Reference
waveform No.8: ” and
“Reference waveform
No.9: ”)While engine running at
2,000 r/min. for 1 min. or
longer after warmed up.
C01-11 BRNOxygen signal of
heated oxygen
sensor-2 (if
equipped)4 – 5 V Ignition switch turned ON.
— *Deflects between
over 0.5 V and under
0.45 V
(“Reference
waveform No.10: ”)While engine running at
2,000 r/min. or more after
vehicle running over 30
km/h, 19 mph for 5 min.
C01-12 WHTCAN (low)
communication line
(active low signal)
to TCM (for A/T
model)*0.5 – 2.5 V
(“Reference
waveform No.23: ”)
Ignition switch turned ON
with engine stop.CAN communication line
signal is pulse. Pulse
signal displayed with a
regular frequency which
varies depending on
engine condition. C01-13 REDCAN (high)
communication line
(active high signal)
to TCM (for A/T
model)*2.5 – 4.5 V
(“Reference
waveform No.23: ”)
C01-14GRY/
REDOutput of 5 V
power source for
MAP sensor and A/
C refrigerant
pressure sensor (if
equipped with A/C)4.5 – 5.5 V Ignition switch turned ON. —
C01-15 BLK Ground for ECM Below 0.3 V Ignition switch turned ON. —
C01-16BLU/
REDFuel injector No.3
output10 – 14 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
10 – 14 V
(“Reference
waveform No.1: ” and
“Reference waveform
No.11: ”)Engine running at idle
after warmed up engine.Output signal is active low
pulse. Pulse frequency
varies depending on
engine speed.
C01-17BLU/
ORNFuel injector No.4
output10 – 14 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
10 – 14 V
(“Reference
waveform No.1: ” and
“Reference waveform
No.12: ”)Engine running at idle
after warmed up engine.Output signal is active low
pulse. Pulse frequency
varies depending on
engine speed.
C01-18BRN/
YELEGR valve
(stepper motor coil
4) output (if
equipped)10 – 14 V Ignition switch turned ON. —
*0 – 1 V
↑↓
10 – 14 V
(“Reference
waveform No.4: ”)Ignition switch is turned to
ST (cranking) position.Output signal is active low
duty pulse. Number of
pulse generated times
varies depending on
vehicle condition. Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-175
C01-19WHT/
REDEGR valve
(stepper motor coil
3) output (if
equipped10 – 14 V Ignition switch turned ON. —
*0 – 1 V
↑↓
10 – 14 V
(“Reference
waveform No.4: ”)Ignition switch is turned to
ST (cranking) position.Output signal is active low
duty pulse. Number of
pulse generated times
varies depending on
vehicle condition.
C01-20RED/
YELCMP sensor signal0 – 1 V or 4 – 5 V Ignition switch turned ON. —
*0 – 0.6 V
↑↓
4 – 5 V
(“Reference
waveform No.13: ”
and “Reference
waveform No.14: ”)Engine running at idle
after warmed up engine.Sensor signal is pulse.
Pulse frequency varies
depending on engine
speed.
(6 pulses are generated
per 1 camshaft revolution.)
C01-21 PNK CKP sensor signal0 – 1 V or 4 – 5 V Ignition switch turned ON. —
*4 – 5 V
↑↓
0 – 0.6 V
(“Reference
waveform No.13: ”
and “Reference
waveform No.14: ”)Engine running at idle
after warming up engine.Sensor signal is pulse.
Pulse frequency varies
depending on engine
speed.
(30 (36 – 6) pulses are
generated per 1
crankshaft revolution.)
C01-22 — — — — —
C01-23 — — — — —
C01-24 LT GRNEngine coolant
temp. (ECT)
sensor signal3.5 – 4.0 VIgnition switch turned ON,
ECT at 0 °C, 32 °F.
— 1.38 – 1.72 VIgnition switch turned ON,
ECT at 50 °C, 122 °F.
0.40 – 0.53 VIgnition switch turned ON,
ECT at 100 °C, 212 °F.
C01-25BLK/
YELIntake air temp.
(IAT) sensor signal3.18 – 3.67 VIgnition switch turned ON,
IAT at 0 °C, 32 °F.
— 1.32 – 1.65 VIgnition switch turned ON,
IAT at 40 °C, 104 °F.
0.46 – 0.60 VIgnition switch turned ON,
IAT at 80 °C, 176 °F.
C01-26GRN/
BLKMass air flow
(MAF) sensor
signal0.5 – 1.5 VIgnition switch turned ON
with engine at stop.
— 1.5 – 2.0 V
(“Reference
waveform No.15: ”)When engine running at
specified idle speed after
warmed up.
C01-27 GRYGround for MAF
sensorBelow 0.3 V Ignition switch turned ON. —
C01-28BLU /
YELGeneral control
signal output0 – 1 VEngine: Stop
IG switch: ON
—
10 – 14 VEngine: Idle speed after
warning up
C01-29BLU/
BLKEVAP canister
purge valve output10 – 14 VIgnition switch turned ON
with engine at stop.—
*0 – 0.6 V
↑↓
10 – 14 V
(“Reference
waveform No.16: ”)Set EVAP canister purge
valve at 52% by using
“Engine / Active Test” of
scan tool.Output signal is active low
duty pulse. Duty ratio
varies depending on
vehicle condition.
C01-30 BLK Ground for ECM Below 0.3 V Ignition switch turned ON. —
C01-31 — — — — —
C01-32 — — — — —
C01-33 — — — — — Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks

Downloaded from www.Manualslib.com manuals search engine 1A-176 Engine General Information and Diagnosis:
C01-34 — — — — —
C01-35 — — — — —
C01-36 — — — — —
C01-37 — — — — —
C01-38 — — — — —
C01-39 — — — — —
C01-40 WHTThrottle position
sensor (sub) signal1.57 – 1.90 VIgnition switch turned ON
and accelerator pedal at
idle position after warmed
up engine.
—
3.88 – 4.45 V
(“Reference
waveform No.29: ”)Ignition switch turned ON
and accelerator pedal at
full depressed position
after warmed up engine.
C01-41 GRYGround for shield
wire of TP sensor
circuitBelow 0.3 V Ignition switch turned ON. —
C01-42 BLKGround for throttle
position sensorBelow 0.3 V Ignition switch turned ON. —
C01-43 REDOutput for 5 V
power source of
throttle position
sensor4.5 – 5.5 V Ignition switch turned ON. —
C01-44 YELOutput of throttle
actuator0 – 1 VIgnition switch turned ON
and accelerator pedal at
idle position after warmed
up engine. Output signal is pulse.
Duty ratio varies
depending on throttle
valve and accelerator
pedal position. *0 – 1 V
↑↓
10 – 14 V
(“Reference
waveform No.26: ”
and “Reference
waveform No.27: ”)Ignition switch turned ON
and accelerator pedal at
full depressed position
after warmed up engine.
C01-45 BLUOutput of throttle
actuator0 – 1 VIgnition switch turned ON
and accelerator pedal at
full depressed position
after warmed up engine. Output signal is pulse.
Duty ratio varies
depending on throttle
valve and accelerator
pedal position. *0 – 1 V
↑↓
10 – 14 V
(“Reference
waveform No.26: ”
and “Reference
waveform No.27: ”)Ignition switch turned ON
and accelerator pedal at
idle position after warmed
up engine.
C01-46BLK/
REDHeater output of
heated oxygen
sensor-110 – 14 V Ignition switch turned ON. —
*0 – 2 V
↑↓
10 – 14 V
(“Reference
waveform No.8: ” and
“Reference waveform
No.9: ”)Engine running at idle
after warmed up engine.Output signal is active low
duty pulse. Duty ratio
varies depending on
engine condition.
C01-47RED/
BLUHeater output of
heated oxygen
sensor-2 (if
equipped)10 – 14 V Ignition switch turned ON.
— 0 – 1 V
(“Reference
waveform No.10: ”)Engine running at idle
after vehicle running over
30 km/h, 19 mph for 5 min. Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks

Downloaded from www.Manualslib.com manuals search engine Engine General Information and Diagnosis: 1A-177
C01-48YEL/
GRNStarting motor
signal0 – 1 V Ignition switch turned ON.
—
6 – 14 V While engine cranking.
C01-49 — — — — —
C01-50WHT/
BLUGround of ECM for
shield wireBelow 0.3 V Ignition switch turned ON. —
C01-51 — — — — —
C01-52 — — — — —
C01-53RED/
BLKManifold absolute
pressure (MAP)
sensor signal (if
equipped)Approx. 4 V
(“Reference
waveform No.17: ”)Ignition switch turned ON
with barometric pressure
at 100 kPa, 760 mmHg.
—
0.4 – 2.0 V
(“Reference
waveform No.18: ”)While engine running at
specified idle speed after
warmed up with
barometric pressure at
100 kPa, 760 mmHg.
C01c01-
54GRNThrottle position
sensor (main)
signal0.75 – 1.08 VIgnition switch turned ON
and accelerator pedal at
idle position after warmed
up engine.
—
3.67 – 4.24 V
(“Reference
waveform No.29: ”)Ignition switch turned ON
and accelerator pedal at
full depressed position
after warmed up engine.
C01-55GRY/
BLUGround for sensors Below 0.3 V Ignition switch turned ON. —
C01-56 REDKnock sensor
signal2 – 3 V
(“Reference
waveform No.19: ”
and “Reference
waveform No.20: ”)Ignition switch turned ON.
— Engine running at 4000 r/
min. after warmed up.
C01-57 ORN Ground for sensors Below 0.3 V Ignition switch turned ON. —
C01-58BLK/
ORNGround for ECM Below 0.3 V Ignition switch turned ON. —
C01-59GRN/
WHTOil control valve
ground (for engine
with VVT system)Below 1.3 V Ignition switch turned ON. —
C01-60GRN/
REDOil control valve
output (for engine
with VVT system)*0 – 0.6 V
↑↓
10 – 14 V
(“Reference
waveform No.21: ”
and “Reference
waveform No.22: ”)At the moment of ignition
switch turned ON.Output signal is active
high pulse. Duty ratio
varies depending on
vehicle condition. Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks
Terminal
No.Wire
colorCircuit Normal voltage Condition Remarks
E01-1BLK/
REDMain power supply 10 – 14 V Ignition switch turned ON. —
E01-2WHT/
REDPower source for
ECM internal
memory10 – 14 V Ignition switch turned ON. —
E01-3 REDCAN (high)
communication line
(active high signal)
to ABS control
module*2.5 – 4.5 V
(“Reference
waveform No.23: ”)Ignition switch turned ON
with engine at stop.CAN communication line
signal is pulse. Pulse
signal displayed with a
regular frequency with
varies depending on
engine condition.