2006 SUBARU LEGACY coolant

11 - 1 6 Maintenance and service
5. Slowly pour the coolant and fill up to
just below the filler neck, allowing enough
room to add genuine Subaru cooling sys-
tem conditioner in the radiator. Add genu-
ine Subaru cooling system conditioner un-
til the coolant level reaches the filler neck.
Do not pour the coolant too quickly, as this
may lead to insufficient air bleeding and
trapped air in the system.
Coolant capacity (Guideline):
2.5-liter non-turbo models: MT. 6.8 US qt (6.4 liters, 5.6 Imp qt)
AT. 6.7 US qt (6.3 liters, 5.5 Imp qt)
2.5-liter turbo models: MT. 7.7 US qt (7.3 liters, 6.4 Imp qt)
AT. 7.6 US qt (7.2 liters, 6.3 Imp qt)
3.0-liter models:
7.6 US qt (7.2 liters, 6.3 Imp qt)6. Pour the coolant and fill to the reservoir
tank’s “FULL” level mark. 7. Put the radiator cap back on and tight-
en firmly. At this time
, make sure that the
rubber gasket in the radiator cap is cor-
rectly in place.
8. Start and run the engine for more than
five minutes at 2,000 to 3,000 rpm.
9. Stop the engine and wait until the cool-
ant cools down (122 to 140 °F [50 to
60 °C]). If there is any loss of coolant, add
coolant to the radiator’s filler neck and to
the reserve tank’s “FULL” level.
10.Put the radiator cap and reservoir cap
back on and tighten firmly.
y
Be careful not to spill engine cool-
ant when adding it. If coolant
touches the exhaust pipe, it may
cause a bad smell, smoke, and/or
a fire. If engine co olant gets on the
exhaust pipe, be sure to wipe it off.
y Do not splash the engine coolant
over painted parts. The alcohol
contained in the engine coolant
may damage the paint surface.
FULL LOW
600151
B00018

Maintenance and service 11 - 3 9
– CONTINUED –
Aluminum wheels
Aluminum wheels can be scratched and
damaged easily. Handle them carefully to
maintain their appearance, performance,
and safety. yWhen any of the wheels is removed and
replaced for tire rotation or to change a
flat, always check the tightness of the
wheel nuts after driving approximately 600
miles (1,000 km). If any nut is loose, tight-
en it to the specified torque.y Never apply oil to the threaded parts,
wheel nuts, or tapered surface of the
wheel.y Never let the wheel rub against sharp
protrusions or curbs.y Be sure to fit tire chains on uniformly
and completely around the tire, otherwise
the chains may scratch the wheel. y When wheel nuts, balance weights, or
the center cap is replaced, be sure to re-
place them with genuine SUBARU parts
designed for aluminum wheels.Windshield washer fluid
If you spray washer fluid on the windshield
but the supply of washer fluid appears to
diminish, check the level of washer fluid in the tank.
Use only those wheels that are
specified for your vehicle. Wheels
not meeting specifications could in-
terfere with brake caliper operation
and may cause the tires to rub
against the wheel well housing dur-
ing turns. The resulting loss of vehi-
cle control could lead to an acci-
dent.
Never use engine coolant as washer
fluid because it could cause paint
damage.
B00199

12-4 Specifications
„ Capacities
Fuel tank16.9 US gal (64 liters, 14.1 Imp gal)
Engine oil2.5-liter models4.2 US qt (4.0 liters, 3.5 Imp qt)
3.0-liter models5.8 US qt (5.5 liters, 4.8 Imp qt)
Transmission oil (MT)3.7 US qt (3.5 liters, 3.1 Imp qt)
Transmission fluid (AT)2.5-liter non-turbo models9.8 US qt (9.3 liters, 8.2 Imp qt)
2.5-liter turbo and 3.0-liter models10.4 US qt (9.8 liters, 8.6 Imp qt)
AT differential gear oil2.5-liter non-turbo models1.3 US qt (1.2 liters, 1.1 Imp qt)
2.5-liter turbo and 3.0-liter models1.5 US qt (1.4 liters, 1.2 Imp qt)
Rear differential gear oil0.8 US qt (0.8 liter, 0.7 Imp qt)
Power steering fluid0.7 US qt (0.7 liter, 0.6 Imp qt)
Engine coolant2.5-liter non-turbo modelsMT6.8 US qt (6.4 liters, 5.6 Imp qt)
AT6.7 US qt (6.3 liters, 5.5 Imp qt)
2.5-liter turbo modelsMT7.7 US qt (7.3 liters, 6.4 Imp qt)
AT7.6 US qt (7.2 liters, 6.3 Imp qt)
3.0-liter models7.6 US qt (7.2 liters, 6.3 Imp qt)

Consumer information and Reporting safety defects 13-7
– CONTINUED –
asymmetrical tire that has a particu-
lar side that must always face out-
ward when mounting on a vehicle.
y Accessory weight
The combined weight (in excess of
those standard items which may be
replaced) of floor mats, leather seats
and cross bars to the extent that these
items are available as factory-in-
stalled equipment (whether installedor not). y Curb weight
The weight of a motor vehicle with
standard equipment including the
maximum capacity of fuel, oil, and
coolant and air conditioning. y Maximum loaded vehicle weight
The sum of curb weight, accessory
weight, vehicle capacity weight and
production options weight. y Normal occupant weight
150 lbs (68 kg) times the number of
occupants (3 occupants). y Occupant distribution
Distribution of occupants in a vehicle,
2 in front, 1 in rear seat. y Production options weight
The combined weight of those in-
stalled regular production options weighing over 5.1 lbs (2.3 kg) in ex-
cess of those standards items which
they replace, not previously consid-
ered in curb weight or accessory
weight. y
Vehicle capacity weight
The total weight of cargo, luggage
and occupants that can be added to
the vehicle. y Vehicle maximum load on a tire
Load on an individual tire that is deter-
mined by distributing to each axle its
share of the maximum loaded vehicle
weight and dividing by two. y Vehicle normal load on a tire
Load on an individual tire that is deter-
mined by distributing to each axle its
share of the curb weight, accessory
weight, and normal occupant weight
and dividing by two. „ Tire care – maintenance and
safety practices
y Check on a daily basis that the tires
are free from serious damage, nails,
and stones. At the same time, check
the tires for abnormal wear.y Inspect the tire tread regularly and
replace the tires before their tread wear indicators become visible. When
a tire’s tread wear indicator becomes
visible, the tire is worn beyond the ac-
ceptable limit and must be replaced
immediately. With a tire in this condi-
tion, driving at even low speeds in wet
weather can cause the vehicle to hy-
droplane. Possible resulting loss of
vehicle control can lead to an acci-
dent. y
To maximize the life of each tire and
ensure that the tires wear uniformly, it
is best to rotate the tires every 7,500
miles (12,500 km). Rotating the tires
involves switching the front and rear
tires on the right-hand side of the ve-
hicle and similarly switching the front
and rear tires on the left-hand side of
the vehicle. (Each tire must be kept on
its original side of the vehicle.) Re-
place any damaged or unevenly worn
tire at the time of ro tation. After tire ro-
tation, adjust the tire pressures and
make sure the wheel nuts are correct-
ly tightened. A tightening torque spec-
ification and a tightening sequence
specification for the wheel nuts can be
found “Flat tires” section in chapter 9.

14-4 Index
Snowy and icy roads ..................................................... 8-9
Tips ..................................................... 7-11, 7-16, 7-23, 8-5
Tired or sleepy ................................................................... 7
E
Electrical system ....... .......................................... ............. 12-3
Electronic Brake Force Distributio n (EBD) system ........... 7-28
Emergency Locking Retractor (ELR) ................................ 1-12
Engine Compartment overview ............. ................................... 11-6
Coolant ...................................................................... 11-14
Exhaust gas (Carbon monoxide) .. ........................... ...... 8-2
Hood ............................................................................ 11-4
Oil ................................................................................ 11-9
Overheating ................................................................. 9-12
Starting .......................................................................... 7-8
Stopping ........................................................................ 7-9
Exterior care ..................................................................... 10-2 F
Flat tires ............................................................................. 9-4
Floor mat .......................................................................... 6-12 Fluid level
Automatic transmission ............................................. 11-22
Brake ......................................................................... 11-28
Clutch ........................................................................ 11-29
Power steering ........................................................... 11-27
Fog light switch ................................................................. 3-34
Front
Differential gear oil ..................................................... 11-23
Fog light ..................................................................... 11-50 Seatbelt pretensioners ................................................. 1-21
Seats .............................................................................. 1-2
Fuel ..................................................................................... 7-2
Economy hints ............................................................... 8-2
Filler lid and cap ............................................................. 7-4
Gauge ................................................................... 3-8, 3-12
Requirements ................................................................ 7-2
Fuses .............................................................................. 11-45
Fuses and circuits ............................................................. 12-6 G
GAWR (Gross Axle Weight Rating ) .................................. 8-14
Glove box ........................................................................... 6-4
GVWR (Gross Vehicle Weight Ra ting) ............................. 8-14
H
Hazard warning flasher ....................................................... 3-5
Head restraint adjustment (Front) ... .................................... 1-5
Headlight
Flasher ......................................................................... 3-32
Indicator light ....................... ........................................ 3-25
Headlights ........... .......................................... ......... 3-31, 11-49
Heater operation ......... .......................................... .............. 4-5
High beam indicator light .................................................. 3-25
High mount stop light ...................................................... 11-56
Horn .................................................................................. 3-43
Hose and connections ................. ................................... 11-14
I
Ignition switch ..................................................................... 3-3 Light ............................................................................... 3-5