2006 SUBARU FORESTER battery

Instruments and controls
3-7
– CONTINUED –
trip or B trip meter by pushing the knob
and keep the knob pushed for more than
2 seconds.NOTEIf the connection between the combi-
nation meter and battery is broken for
any reason such as vehicle mainte-
nance or fuse replacement, the data re-
corded on the trip meter will be lost.„TachometerThe tachometer shows the engine speed
in thousands of revolutions per minute.
„Fuel gauge1) Low fuel warning lightThe fuel gauge shows the approximate
amount of fuel remaining in the tank.
The gauge does not return to “E” even though the ignition switch is in the “ACC”
or “LOCK” position.
The gauge may move slightly during brak-
ing, turning or acceleration due to fuel lev-
el movement in the tank.
NOTEYou will see the “FUEL DOOR ” sign
near the fuel gauge.
This indicates that the fuel filler door
(lid) is located on the right side of the
vehicle.
T
Low fuel warning light
The low fuel warning light comes on when
the tank is nearly empty [approximately
2.3 US gal (9.0 liters, 1.9 Imp gal)]. It only
operates when the ignition switch is in the
“ON” position.
To ensure safety, do not attempt to
change the function of the indicator
during driving, as an accident could
result.
Do not operate the engine with the
pointer of the tachometer in the red
zone. In this range, fuel injection will
be cut by the engine control module
to protect the engine from overrev-
ving. The engine will resume run-
ning normally after the engine
speed is reduced below the red
zone.
1
300573
300121
ProCarManuals.com

Instruments and controls
3-13
– CONTINUED –
With a vehicle equipped with an EBD sys-
tem, the ABS warning light comes on to-
gether with the brake system warning light
if the EBD system becomes faulty. For fur-
ther details of the EBD system fault warn-
ing, refer to “Brake system warning light”.NOTEIf the warning light behavior is as de-
scribed in the following, the ABS sys-
tem may be considered normal.
yThe warning light comes on right af-
ter the engine is started but goes out
immediately, remaining off.
y The warning light remains on after
the engine has been started, but it goes
out when the vehicle speed reaches
approximately 8 mph (12 km/h).
y The warning light comes on during driving, but it goes out immediately
and remains off.
When driving with an insufficient battery
voltage such as when the engine is jump
started, the ABS warning light may come
on. This is due to the low battery voltage
and does not indicate a malfunction.
When the battery becomes fully charged,
the light will go out.
„
Vehicle Dynamics Con-
trol warning light (if
equipped)/Vehicle Dy-
namics Control OFF indicator
light (if equipped)This warning light has the function of indi-
cating faults in the Vehicle Dynamics Con-
trol system and the function of indicating
that the Vehicle Dynamics Control system
has been deactivated.
It comes on in the event of a fault in the
system and is on when the system is not
operating.
This warning light comes on when the ig-
nition switch is turned to the “ON” position
and goes out after the engine has started.
It indicates that the Vehicle Dynamics
Control system is in normal operation. T
Vehicle Dynamics Control warning
light
The Vehicle Dynamics Control system is
probably inoperative under any of the fol-
lowing conditions. Have your vehicle
checked at a SUBARU dealer immediate-
ly.
y The warning light does not come on
when the ignition switch is turned to the
“ON” position.
y The warning light comes on while the
vehicle is running.
y If the electrical circuit of the Vehicle Dy-
namics Control system itself becomes
faulty, the warning light only comes on. At
this time, the ABS (Anti-lock Brake Sys-
tem) remains fully operational.
y The warning light comes on when the
electronic control system of the ABS/Vehi-
cle Dynamics Control system becomes
faulty.
The Vehicle Dynamics Control system
provides its ABS control through the elec-
trical circuit of the ABS system. Accord-
ingly, if the ABS is inoperative, the Vehicle
Dynamics Control system becomes un-
able to provide ABS control. As a result,
the Vehicle Dynamics Control system also
becomes inoperative, causing the warning
light to come on. Though both the Vehicle
Dynamics Control and ABS systems are
inoperative in this case, the ordinary func-
y
The warning light comes on when
the ignition switch is turned to the
“ON” position, but it does not go
out even when the vehicle speed
exceeds approximately 8 mph (12
km/h).
y The warning light comes on dur-
ing driving.
If any of these conditions occur,
have the ABS system repaired at the
first available opportunity by your
SUBARU dealer.
ProCarManuals.com

3-18
Instruments and controls
Light control switchThe light switch operates only when the
ignition switch is in the “ON” position.
„HeadlightsTo turn on the headlights, turn the knob on
the end of the turn signal lever.
first position:
Parking lights, instrument panel illumina-
tion, front side marker lights, tail lights and
license plate light are on.
second position:
Headlights, parking lights, instrument pan-
el illumination, front side marker lights, tail
lights, and license plate light are on.
„ High/low beam change (dim-
mer)To change from low beam to high beam,
push the turn signal lever forward. When
the headlights are on high beam, the high
beam indicator light “ ” on the instru-
ment panel is also on.
To switch back to low beam, pull the lever
back to the detent position.
To prevent battery discharge result-
ing from accidentally leaving your
lights on when your vehicle is
parked, the light switch operates
only when the ignition switch is in
the “ON” position. In any other posi-
tion, the vehicle’s lights will be out.If you park your vehicle on a road-
side at night, use the hazard warn-
ing flasher to alert the other drivers.
300127
300128
ProCarManuals.com

Instruments and controls
3-25
– CONTINUED –
Windshield wiper deicer (if equipped)The windshield wiper deicer operates only
when the ignition switch is in the “ON” po-
sition.
Before turning on the windshield wiper de-
icer, remove any snow from the wind-
shield. To turn on the windshield wiper de-
icer, push the button. The indicator light
located on the button lights up while the
windshield wiper deicer is operating.
The windshield wiper deicer will automati-
cally shut off after approximately 15 min-
utes. If the wiper blades have been deiced
completely before that time, push the but-
ton to turn it off. It also turns off when the
ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not com-
plete, you have to push the button to turn
the deicer on again.
NOTEIf your vehicle is equipped with the out-
side mirror defogger, the outside mir-
ror defogger operates while the wind-
shield wiper deicer is operating.
Rear window defogger but-tonManual climate control system
Automatic climate control system
300143
To prevent the battery from being
discharged, do not operate the
windshield wiper deicer continuous-
ly for any longer than necessary.
300151300142
ProCarManuals.com

3-26
Instruments and controls
The rear window defogger operates only
when the ignition switch is in the “ON” po-
sition.
The rear window defogger button is locat-
ed on the climate control panel.
To turn on the defogger, push the button.
To turn it off, push the button again.
The indicator light located on the button
lights up while the rear window defogger is
operating.
The defogger will automatically shut off af-
ter approximately 15 minutes. If the win-
dow clears before that time, push the but-
ton to turn it off. It also turns off when the
ignition switch is turned to the “ACC” or
“LOCK” position. If defrosting or defogging
is desired when you restart your vehicle,
you have to push the button to turn it on
again.
Turn on the rear window defogger if the
wiper is frozen to the glass.
MirrorsAlways check that the inside and outside
mirrors are properly adjusted before you
start driving.„Inside mirrorThe inside mirror has a day and night po-
sition. Pull the tab at the bottom of the mir-
ror toward you for the night position. Push
it away for the day position. The night po-
sition reduces glare from headlights.
y
Do not use sharp instruments or
window cleaner containing abra-
sives to clean the inner surface of
the rear window. They may dam-
age the conductors printed on the
window.
yTo prevent the battery from being
discharged, do not operate the de-
fogger continuously for any long-
er than necessary.
300145
ProCarManuals.com

Instruments and controls
3-29
TOutside mirror defogger1) Outside mirror defogger button (if
equipped)
2) Outside mirror defogger and windshield wiper deicer button (if equipped)The outside mirror defogger operates only
when the ignition switch is in the “ON” po-
sition.
To turn on the outside mirror defogger,
push the button. To turn it off, push the
button again. The indicator light located
on the button lights up while the outside
mirror defogger is operating.
The defogger will automatically shut off af-
ter approximately 15 minutes. If the mirror
clears before that time, push the button to
turn it off. It also turns off when the ignition
switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is de-
sired when you restart your vehicle, you
have to push the button to turn it on again.
NOTEOn vehicles equipped with a wind-
shield wiper deicer, the windshield
wiper deicer switch is also used to op-
erate the outside mirror defogger.
Tilt steering wheel1. Adjust the seat position. Refer to the
“Front seats” section (chapter 1).
2. Push the tilt lock lever down.
3. Move the steering wheel to the desired
level.
4. Pull the lever up to lock the steering
wheel in place.
5. Make sure that the steering wheel is
securely locked by moving it up and down.
12
300582
To prevent the battery from being
discharged, do not operate the de-
fogger continuously for any longer
than necessary.
Do not adjust the steering wheel tilt
position while driving. This may
cause loss of vehicle control and re-
sult in personal injury.
300149
ProCarManuals.com

5-6
Audio
TFM/AM/Weather band selection but-
ton (BAND)
Push the “BAND” button when the radio is
on to select FM1, FM2, AM or Weather
band (WB) reception. Each time this but-
ton is pressed, the band will change in the
following order:
The display indicates which one is cur-
rently selected.
T Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received.
T Tuning (TUNE)
V Manual tuning (TUNE)
Push the “ ” side of the tuning button
(3) to increase the tuning frequency and
press the “ ” side of the button to de-
crease it.
Each time the button is pressed, the fre-
quency changes 10 KHz in the AM wave-
band and 0.2 MHz in the FM waveband.
V Manual tuning for weather band
When weather band mode is selected,
press the “ ” side of the tuning button (3) to change the WB channel up and
press the “ ” side of the tuning button
to change the WB channel down. Each
time the button is pressed, the WB chan-
nel changes to the next channel.
T
Seek tuning
If the tuning button (3) is pressed for long-
er than half of a second, the radio will be-
gin to automatically search for receivable
frequencies and will stop at the first one
found. This function may not be available,
however, when radio signals are weak. In
such a situation, perform manual tuning to
select the desired station.
T Automatic tuning (SCAN)
Press the “SCAN” button (6) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper- ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.
T
Selecting preset stations
Presetting a station with a preset button
(4) allows you to select that station in a
single operation. Up to six WB, AM, FM1
and FM2 stations each may be preset.
T How to preset stations
1. Press the “BAND” selection button to
select AM, FM1, FM2 or WB reception.
2. Press the “SCAN” button (6) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (4) for
at least 2 seconds to store the frequency.
At this time, there will momentarily be no
sound from the radio. If the button is
pressed for less than 2 seconds, the pre-
ceding selection will remain in memory.
NOTEy If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.
y If a cell phone is placed near the ra-
dio, it may cause the radio to emit
FM1 FM2 AM
WB
ProCarManuals.com

Audio
5-15
– CONTINUED –
select the desired station.
TAutomatic tuning (SCAN)
Press the “SCAN” button (1) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills.
T Selecting preset stations
Presetting a station with a preset button
(7) allows you to select that station in a
single operation. Up to six AM, FM1, FM2
and WB stations each may be preset.
T How to preset stations
1. Press the “FM/AM” selection button to
select AM, FM1 or FM2 reception.
OR
Press the “WB” button (3) to select the
weather band.
2. Press the “SCAN” button (1) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (7) for
at least 1.5 seconds to store the frequen-
cy. The frequency of the station will flash
once on the display at this time.
NOTEy If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons.
y If a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when it receives calls. This noise
does not indicate a radio fault.
ProCarManuals.com