2006 SUBARU FORESTER light

11 - 4 4
Maintenance and service
WattageBulb No.
1) High beam headlight 12V-60W9005 (HB3)
2) Low beam headlight Canada-spec. 2.5XT 12V-35W D2R
All except Canada-spec.
2.5XT 12V-55W
H1
3) Front turn signal light 12V-21W (Amber) 1474
4) Map light 12V-8W–
5) Dome light 12V-8W–
6) Side marker light (Front) 12V-5W 168
7) Front fog light 12V-55W9006 (HB4)
8) Parking light 12V-5W168
9) High mount stop light 12V-13W912
10) Cargo area light 12V-5W–
11) Tail/stop light 12V-21/5W7443
12) Backup light 12V-16W921
13) Rear turn signal light 12V-21W (Amber) 1474
14) Tail/stop light 12V-21/5W7443
15) License plate light 12V-5W168
„Headlights (Canada-spec.
2.5XT)Replace any bulb only with a new
bulb of the specified wattage. Using
a bulb of different wattage could re-
sult in a fire.High-intensity-discharge (HID) bulbs
are used for the low beams of the
headlights on the Canada-spec.
2.5XT. These HID bulbs use an ex-
tremely high voltage. To avoid the
risk of an electric shock and result-
ing serious injury, you should not at-
tempt to replace them. Neither
should you attempt to replace the
high-beam bulbs, remove/refit the
headlight assemblies, or remove any
headlight-assembly components.
For replacement of the headlight
bulbs (low-beam and high-beam), re-
moval and installation of the head-
light assemblies, and removal of
headlight-assembly components,
contact your SUBARU dealer.
ProCarManuals.com

Maintenance and service
11 - 4 5
– CONTINUED –
„Headlights (Except Canada-
spec. 2.5XT)Before replacing the left-hand (battery-
side) low- or high-beam light bulb, remove
the screw that retains the windshield
washer nozzle and tip the windshield
washer nozzle sideways.
NOTEyIf headlight aiming is required, con-
sult your SUBARU dealer for proper
adjustment of the headlight aim.
y It may be difficult to replace the
bulbs. Have your SUBARU dealer re-
place the bulbs if necessary. T
Low beam light bulbs
1. Remove the bulb cover, by turning it
counterclockwise.
2. Remove the retainer spring, then pull
out the bulb and electrical connector unit.
B00393
Halogen headlight bulbs become
very hot while in use. If you touch
the bulb surface with bare hands or
greasy gloves, finger prints or
grease on the bulb surface will de-
velop into hot spots and cause the
bulb to break. If there are finger
prints or grease on the bulb surface,
wipe them away with a soft cloth
moistened with alcohol.
B00385B00386
ProCarManuals.com

11 - 4 6
Maintenance and service
3. Disconnect the electrical connector
from the bulb.
4. Install a new bulb into the electrical
connector, then set the retainer spring se-
curely.
5. Install the bulb cover.T
High beam light bulbs
1. Disconnect the electrical connector
from the bulb.
2. Remove the bulb from the headlight
assembly by turning it counterclockwise. 3. Replace the bulb with new one.
4. Reconnect the electrical connector. At
this time, use care not to touch the bulb
surface.
5. To install the bulb to the headlight as-
sembly, turn it clockwise until it clicks.
„
Rear combination lights1. Remove the upper and lower screws.
Then, slide the rear combination lamp as-
sembly to the rear and remove it from the
vehicle.
B00387
700093B00388
B00389
ProCarManuals.com

Maintenance and service
11 - 4 7
– CONTINUED –
1) Tail/stop light
2) Backup light
3) Rear turn signal light
4) Tail/stop light2. Remove the bulb holder from the rear
combination light assembly by turning it
counterclockwise.
3. Pull the bulb from the holder. Install a
new bulb.
4. Set the bulb holder into the rear combi-
nation light assembly and turn it clockwise
until it locks.
5. Reinstall the rear combination light as-
sembly.
„License plate light
0
1. Remove the mounting screws using a
Phillips screwdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a
new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.
„Dome light and map lightDome light
Map light1. Remove the lens by prying the edge of
1234
B00390
B00391
B00090B00091
ProCarManuals.com

11 - 4 8
Maintenance and service
the lens with a flat-head screwdriver.
2. Pull the bulb out of the socket. Install a
new bulb.
3. Reinstall the lens.„High mount stop light
0
1. Remove the mounting screw covers by
prying the edge with a flat-head screwdriv-
er.
2. Remove the mounting screws using a
Phillips screwdriver and then remove the
high mount stop light cover.
3. Pull the bulb from the socket. Install a
new bulb.
4. Reinstall the cover.
5. Tighten the mounting screws then rein-
stall the covers.
NOTEOther bulbs may be difficult to replace.
Have your SUBARU dealer replace
these bulbs if necessary.
B00093
ProCarManuals.com

Specifications
12-5
„Tires
„ Wheel alignmentTire size
P215/60R16 94H
P215/55R17 93H
Wheel size
16 × 6
1/2 JJ
17 × 7 JJ
Pressure
Front
Light load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Full load
29 psi (200 kPa, 2.0 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Rear
Light load
28 psi (190 kPa, 1.9 kgf/cm
2)
30 psi (210 kPa, 2.1 kgf/cm
2)
Full load
36 psi (250 kPa, 2.5 kgf/cm
2)
32 psi (220 kPa, 2.2 kgf/cm
2)
Trailer towing
41 psi (280 kPa, 2.8 kgf/cm
2)
36 psi (250 kPa, 2.5 kgf/cm
2)
Temporary spare tire
Size
T135/80D16
T135/90D16
Pressure
60 psi (420 kPa, 4.2 kgf/cm
2)
Item
2.5-liter non-turbo models
2.5-liter turbo models
Drive system
AWD
Toe
Front
0 ± 0.12 in (0 ± 3 mm)
Rear
0.079 ± 0.12 in (2 ± 3 mm)
Camber
Front
–0°25’ ± 45’
Rear
–0 °50’ ± 45’
–0 °55’ ± 45’
ProCarManuals.com

12-6
Specifications
Fuses and circuits„Fuse panel located behind the instrument pan-
el
1 234 56
789101112
1413 15 16 17 18 19
20 21 22 23
C00000
Fuse panel
Fuse rating
Circuit
1
15A
y
Heater fan
2
15A
y
Heater fan
3
15A
y
Power door lock
y
Remote keyless entry
4
15A
y
Cigarette lighter
y
Remote controlled rear view mirrors
5
10A
y
Tail light
y
Parking light
6
15A
y
SRS airbag
7
15A
y
Fog light
8
30A
y
ABS
y
Vehicle Dynamics Control system
(models with Vehicle Dynamics
Control system only)
9
15A
y
Radio
10
Empty
11
15A
y
Engine ignition system
y
SRS airbag
y
AT control system
12
10A
y
Illumination brightness control
13
20A
y
Wiper deicer
y
Outside mirror defogger
ProCarManuals.com

Specifications
12-7
– CONTINUED –
„Fuse panel located in the engine compartmentA) FWD socket (AT models without Vehicle Dynamics Control sys-
tem)
B) Main fuse
14
10A
y
Meter
15
30A
y
Windshield wiper and washer
16
20A
y
Brake light
17
15A
y
Air conditioner
18
15A
y
Backup light
y
Cruise control
19
15A
y
Power outlet (cargo)
20
15A
y
Rear window wiper and washer
21
15A
y
Ignition coil (Non-turbo model only)
22
15A
y
Seat heater
23
Empty
Fuse panel
Fuse rating
Circuit
A
12 4
3 B
5
6 789
10 11 12 13
C00105
14
ProCarManuals.com