2006 SUBARU BAJA change time

Foreword
Congratulations on choosing a SUBARU vehicle. This Owner’s Man-
ual has all the information necessary to keep your SUBARU in excel-
lent condition and to properly maintain the emission control system
for minimizing emission pollutants. We urge you to read this manual
carefully so that you may understand your vehicle and its operation.
For information not found in this Owner’s Manual, such as details
concerning repairs or adjustments, please contact the dealer from
whom you purchased your SUBARU or the nearest SUBARU dealer.
The information, specifications and ill ustrations found in this manual
are those in effect at the time of printing. FUJI HEAVY INDUSTRIES
LTD. reserves the right to change specifications and designs at any
time without prior notice and wi thout incurring any obligation to
make the same or similar changes on vehicles previously sold. This
Owner’s Manual applies to all models and covers all equipment, in-
cluding factory installed options. Some explanations, therefore may
be for equipment not installed in your vehicle.
Please leave this manual in the vehicle at the time of resale. The next
owner will need the information found herein.
FUJI HEAVY INDUSTRIES LTD., TOKYO, JAPAN
is a registered trademark of FUJI HEAVY INDUSTRIES LTD.
© copyright 2005 FUJI HEAVY INDUSTRIES LTD.

1-33
Seat, seatbelt and SRS airbags
– CONTINUED –
4. Take up the slack in the lap belt.
5. Pull out the seatbelt fully from the retractor to
change the retractor over from the Emergency Lock-
ing Retractor (ELR) to the Automatic Locking Retrac-
tor (ALR) function. Then, allow the belt to rewind into
the retractor. As the belt is rewinding, clicks will be
heard which indicate the retractor functions as ALR. 6. Push and pull the child
restraint system forward
and from side to side to check if it is firmly secured.
Sometimes a child restraint can be more firmly se-
cured by pushing it down in to the seat cushion and
then tightening the seatbelt.
7. Pull at the shoulder portion of the belt to confirm
that it cannot be pulled out (ALR properly functioning).
UBS110BAUBS111BA

2-18
Keys and doors
seconds.
The alarm is triggered by: y
Opening a door
y Turning the ignition swit ch to the “ON” position
y Physical impact to the vehicle, such as forced entry
(only vehicles with shock sensors (dealer option)) „ Activating and deactivating the alarm
system
To change the se tting of your vehicle’s alarm system
for activation or deactivation, do the following.
1. Disarm the alarm system (see “Disarming the sys-
tem” in this section).
2. Sit in the driver’s seat and shut all doors.
3. Turn the ignition switch to the “ON” position.
4. Hold down the UNLOCK side of the driver’s power
door locking switch, open the driver’s door within the
following 1 second, and wait 10 seconds without re-
leasing the switch. The setting will then be changed as
follows:
If the system was previously activated:
The horn sounds twice, indicating that the system is
now deactivated.
If the system was previously deactivated:
The horn sounds once, indi cating that the system is now activated.
NOTE
You may have the above setting change done by
your SUBARU dealer. „
If you have accidentally triggered the
alarm system
T To stop the alarm
Do any of the following operations: y Press any button on the remote transmitter.
y Cycle the ignition switch from the “LOCK” to “ON”
position three time s within 5 seconds.
„ Arming the system
„Arming the system
TTo arm the system using remote transmitter
1. Close all windows and the moonroof (if equipped).
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood is locked.
5. Close all doors.

2-21
Keys and doors
– CONTINUED –
„Disarming the system„
Disarming the systemBriefly press the “ ” button (for less than two sec-
onds) on the remote transmitter. The driver’s door will
unlock, an electronic chirp will sound twice, the turn
signal lights will flash twice and the indicator light will
go off.
NOTE
The system can be disarmed by the following
method. yCycle the ignition switch from the “LOCK” to the
“ON” position three times within 5 seconds. T Emergency disarming
If you cannot disarm the system using the transmitter
(i.e. the transmitter is lost, broken or the transmitter
battery is too weak), yo u can disarm the system with-
out using the transmitter.
1. Unlock the door with the key and then open the
door.
2. Insert the key into the ignition switch and cycle it
from the “LOCK” to the “ON” position three times with-
in 5 seconds .
„ Valet mode
„Valet modeWhen you choose the valet mode, the security system
does not operate. In valet mode, the remote transmit- ter is used only for locking and unlocking the doors
and panic activation.
To enter the valet mode, chang
e the setting of your ve-
hicle’s alarm system for deactivation mode. (Refer to
“Activating and deactivating the alarm system” in thissection.)
To exit valet mode, change the setting of your vehi-
cle’s alarm system for activation mode. (Refer to “Ac- tivating and deactiva ting the alarm system” in this sec-
tion.)
NOTE
The security indicator light does not flash during the valet mode. „ Passive arming
When passive arming mode has been programmed by
the dealer, arming of the syst em is automatically ac-
complished without using the remote transmitter. Note
that in this mode, DOORS MUST BE MANUALLY LOCKED. T To enter the passive mode
If you wish to program the passive arming mode, have
it done by your SUBARU dealer.

3-1
3
Instruments and controls
Ignition switch .............................................. 3-2 LOCK .................................................................. 3-3
ACC .................................................................... 3-4
ON ....................................................................... 3-4
START ................................................................ 3-4
Key reminder chime .......................................... 3-4
Ignition switch light (if equipped) .................... 3-4
Key interlock release (AT vehicles) ................. 3-5
Hazard warning flasher ................................ 3-6
Meters and gauges ....................................... 3-6 Speedometer ..................................................... 3-6
Odometer/Trip meter ........................................ 3-6
Tachometer ........................................................ 3-8
Outside temperature indicator (if equipped) .. 3-8
Fuel gauge ......................................................... 3-8
Temperature gauge ........................................... 3-9
Warning and indicator lights ....................... 3-11 Seatbelt warning light and chime .................... 3-11
SRS airbag system warning light .................... 3-11
CHECK ENGINE warning light/Malfunction indicator lamp ................................................. 3-12
Charge warning light ........................................ 3-13
Oil pressure warning light ................................ 3-13
AT OIL TEMPerature warning light (AT vehicles) ................................................... 3-13
ABS warning light ............................................. 3-14
Brake system warning light ............................. 3-15
Door ajar warning lights ................................... 3-15
Switchback door indicator light ...................... 3-15
Low fuel warning light ...................................... 3-16
All-Wheel Drive warning light (AT vehicles) ... 3-16 Security system status indicator light
(if equipped) .................................................... 3-17
Selector lever position indicator (AT vehicles) ................................................... 3-17
Gear position indicator (Turbo-AT vehicles) .. 3-17
Turn signal indicator lights .............................. 3-17
High beam indicator light ................................. 3-18
Cargo lamp indicator light ............................... 3-18
Cruise control set indicator light .................... 3-18
Clock .............................................................. 3-19
Light control switch ...................................... 3-19 Headlights ......................................................... 3-20
High/low beam change (dimmer) .................... 3-20
Headlight flasher ............................................... 3-21
Daytime running light system ......................... 3-21
Turn signal lever ........................................... 3-22
Illumination brightness control ................... 3-23
Parking light switch ...................................... 3-23
Front fog light button ................................... 3-24
Wiper and washer ......................................... 3-25 Windshield wiper and washer switches ......... 3-26
Rear window defogger button ..................... 3-28
Windshield wiper deicer (if equipped) ........ 3-29
Mirrors ............................................................ 3-30 Inside mirror ...................................................... 3-30
Outside mirrors ................................................. 3-32
Tilt steering wheel ......................................... 3-34
Horn ................................................................ 3-35

5-9
Audio
– CONTINUED –
TWaveband selection
V FM/AM selection
Push the “BAND” button (2) to select FM1, FM2 or AM
reception. The display indicates which one is currently selected. T Stereo indicator
The stereo indicator “ST” will come on when an FM
stereo broadcast is received. T Tuning (TUNE)
V Manual tuning (TUNE)
Press the “ ” side of the tuning button (3) to in-
crease the tuning frequency and press the “ ” side
of the button to decrease it.
Each time the button is pressed, the frequency interval
can be changed between 10 kHz in the AM mode and
0.2 MHz in the FM mode. V Seek tuning (SEEK)
If the tuning button (3) is pressed for longer than half
of a second, the radio will begin to automatically
search for receivable frequencies and will stop at the
first one found. This function may not be available,
however, when radio signals are weak. In such a situ-
ation, perform manual tuning to select the desired sta-
tion. V
Automatic tuning (SCAN)
Press the “SCAN” button (6) to change the radio to the
SCAN mode. In this mode, the radio scans through the
radio band until a station is found. The radio will stop
at the station for five seconds while displaying the fre-
quency, after which scanning will continue until the en-
tire band has been scanned from the low end to the
high end.
Press the “SCAN” button again to cancel the SCAN
mode and to stop on any displayed frequency.
When the “SCAN” button is pressed for automatic tun-
ing, stations are scanned in the direction of low fre-
quencies to high frequencies only.
Automatic tuning may not function properly if the sta-
tion reception is weakened by distance from the sta-
tion or proximity to tall buildings and hills. T Selecting preset stations
Presetting a station with a “Preset” button (4) allows
you to select that station in a single operation. Up to
six AM, FM1 and FM2 stations each may be preset. T How to preset stations
1. Press the “BAND” button (2) to select FM1, FM2 or
AM reception.
2. Press the “SCAN” button or tune the radio manually
until the desired station frequency is displayed.
3. Press one of the “Preset” buttons for more than 2

5-20
Audio
V
Tone control
The volume control dial (1) normally function as vol-
ume control. The dial become a control for Bass,
Midrange or Treble when you select the appropriate
tone control mode. Choose desired volume level for each mode by turning
the volume control dial. The control function returns to
volume control mode after approximately 5 seconds.
To change control modes: Each brief press of the
“AUDIO” button (2) changes control modes in the fol-
lowing sequence starting from bass control mode.
(When the radio is first turned on, the control mode is
in the volume control.) V Fader and balance control
The volume control dial (1) normally function as vol-
ume control. The dial become the controls for Fader or
Balance when you select the appropriate fader and
balance control mode.
Choose desired setting for each mode by turning the
volume control dial. The control function returns to vol-
ume control mode after approximately 5 seconds.
To change control modes: Each brief press of the “BAL” button (3) changes control modes in the follow-
ing sequence starting from
fader control mode. (When
the radio is turned on, the control mode is in the vol-
ume control.) V Display illumination dimness cancellation (BRIGHT)
The brightness of the radio display dims when the light
switch is in the “ ” or “ ” positions. If this
makes the display difficult to read, press the volume
dial for more than 1.5 seconds to return the display to
original brightness.
Subsequently pressing the volume dial again for more
than 1.5 seconds or if you c an safely do so, turning the
light switch to the OFF position and back to the
“ ” or “ ” position makes the radio display
dim again. T FM/AM selection button
V FM button
Press the “FM” button (4) for FM reception. The radio
will toggle between FM1 and FM2 settings each time
the “FM” button (4) is subsequently pressed.
Volume
Bass Midrange Treble
Volume
Fader Balance

5-21
Audio
– CONTINUED –
VAM button
Press the “AM” button (5) for AM reception. T Stereo indicator
The stereo indicator “ST” will come on when an FM
stereo broadcast is received. T Manual tuning (TUNE)
V Manual tuning for AM and FM
Push the “ ” side of the tuning button (7) to in-
crease the tuning frequency and press the “ ” side
of the button to decrease it.
Each time the button is pr essed, the frequency chang-
es 10 KHz in the AM waveband and 0.2 MHz in the FM
waveband. V Seek tuning (SEEK)
If the tuning button (7) is pressed for longer than half
of a second, the radio will begin to automatically
search for receivable frequencies and will stop at the
first one found. This function may not be available,
however, when radio signals are weak. In such a situ-
ation, perform manual tuning to select the desired sta-
tion. T Automatic tuning (SCAN)
Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the
radio band until a station is
found. The radio will stop
at the station for five seconds while displaying the fre-
quency, after which scanning will continue until the en-
tire band has been scanned from the low end to the
high end.
Press the “SCAN” button again to cancel the SCAN
mode and to stop on any displayed frequency.
When the “SCAN” button is pressed for automatic tun-
ing, stations are scanned in the direction of low fre-
quencies to high frequencies only.
Automatic tuning may not function properly if the sta-
tion reception is weakened by distance from the sta-
tion or proximity to tall buildings and hills. T Selecting preset stations
Presetting a station with a “Preset” button (6) allows
you to select that station in a single operation. Up to
six AM, FM1 and FM2 stations each may be preset. T How to preset stations
1. Press the “FM/AM” selection button to select AM,
FM1 or FM2 reception.
2. Press the “SCAN” button (8) or tune the radio man-
ually until the desired stat ion frequency is displayed.
3. Press one of the “Preset” buttons (6) for at least 1.5
seconds to store the frequency. The frequency of the
station will flash once on the display at this time. If the