2006 SUBARU BAJA key

6-26
Interior and exterior equipments
The front and rear sections
of the bed cover can each
be locked and unlocked. Each section is automatically
locked when it is closed. (Refer to “Opening and clos-
ing the hard bed cover” in this section.)
T Front section
1) Lock
2) Unlock
To unlock the front section, uncover the key cylinder,
insert the key into the key cylinder, and turn it counter- clockwise.
When the key is released, it automatically returns to
the lock position.NOTE If you find the key hard to turn when unlocking the
front section, press the middle of the front section
with your other hand while turning the key. T Rear section
1) Lock
2) Unlock
To unlock the rear section, uncover the key cylinder,
insert the key into the key cylinder, and turn it counter- clockwise.
When the key is released, it automatically returns to the lock position.
1
2
UB6079BA
2 1
UB6079BB

6-27
Interior and exterior equipments
– CONTINUED –
NOTE
If you find the key hard to turn when unlocking the
rear section, press the middle of the rear section
with your other hand while turning the key. „Internal hard bed cover release handle
Never allow any child to get in the cargo bed
and play with the release handle. If the driver
starts the vehicle without knowing that a child
is inside the cargo bed and the child opens the
lid using the release handle, the child could fall
out and be killed or seriously injured.
yDo not close the hard bed cover while grip-
ping the release handle. The handle may be
damaged.y Do not use the handle as a hook to fasten
straps or ropes to secure your cargo in the car-
go bed. Such use may result in damage of the
handle. y Load the cargo bed so that cargo can not strike the release handle. If the cargo hits the
handle while the vehicle is being driven, the
handle may be pushed and the hard bed cover
may open. That may cause cargo to fall out of
the cargo bed, which could create a traffic safe-
ty hazard.
The internal release handle is designed to open the
hard bed cover from inside the cargo bed. In the event
that children or adults become locked inside the cargo
bed, the handle allows them to open the cover. The
handle is located at the back of the rear section of thecover.

6-29
Interior and exterior equipments
– CONTINUED –
bars with the attached strap. Failure to do so
may result in damage to cargo.yWhen opening or closing the cover, hold the
cover by hand and open or close the cover
slowly. Be carefu l not to trap your fingers be-
tween the cover and cargo bed. y When opening the front cover, be sure to re-
move the key from the key cylinder. With the
key remaining inserted in the key cylinder, the
key cylinder cap may be damaged when the
cover is fully opened.
The front section and rear section of the cover can be
opened and closed independently. Each section is au-
tomatically locked when it is closed. T Front section
1. Unlock the front section of the cover. (Refer to
“Locking and unlocking the bed cover” in this section.)
Front section fully opened
UB6059BA
UB6066BA

6-30
Interior and exterior equipments
2. Raise the cover slightly while holding the key in the
unlock position. After making
sure that the cover is
completely unlocked, remove the key from the key cyl-
inder and open the cover slowly to the fully opened po-sition.
3. When closing the cover, lower the cover until it ap-
proaches approximately 6 in (15 cm) from the closed
position and let it drop. The cover will lock automatical-ly.
4. After closing the cover, be sure the cover is secure-
ly locked.
If this does not lock the cover, release it from a slightly
higher position. Do not push the cover forcibly to lock it. T Rear section
1. Unlock the rear section of the cover. (Refer to
“Locking and unlocking the bed cover” in this section.) 2. Raise the cover slightly while holding the key in the
unlock position. After making
sure that the cover is
completely unlocked, remove the key from the key cyl-
inder and open the cover slow ly until it contacts the
rear sport bars.
UB6058BA

7-9
Starting and operating
– CONTINUED –
Starting the engine
Do not operate the starter motor continuously
for more than ten seconds. If the engine fails to
start after operating the starter for five to ten
seconds, wait for ten seconds or more before
trying again.
„ Manual transmission vehicle
1. Apply the parking brake.
2. Turn off unnecessary lights and accessories.
3. Press the clutch pedal to the floor and shift the shift
lever into neutral.
Hold the clutch pedal to the floor while starting the en-
gine. The starter motor will only operate when the
clutch pedal is pressed fully to the floor.
4. Turn the ignition switch to the “ON” position and
check the operation of the warning and indicator lights.
Refer to the “Warning and indicator lights” section
(chapter 3).
5. Turn the ignition switch to the “START” position
without depressing the accelerator pedal. Release
the key immediately after the engine has started. If the engine does not start, try the following.
1) Turn the ignition switch to the “OFF” position and
wait for at least 10 seconds. After checking that the
parking brake is firmly set, turn the ignition switch to
the “START” position while depressing the acceler-
ator pedal slightly (about a quarter of the full stroke).
Release the accelerator pedal as soon as the en-
gine starts.
2) If this fails to start th e engine, turn the ignition
switch back to the “OFF” position and wait for at
least 10 seconds. Then fully depress the accelerator
pedal and turn the ignition switch to the “START”
position. If the engine starts, quickly release the ac-
celerator pedal.
3) If this fails to start th e engine, turn the ignition
switch again to the “OFF” position. After waiting for
10 seconds or longer, turn the ignition switch to the
“START” position without depressing the accelera-
tor pedal.
4) If the engine still refuses to start, contact your
nearest SUBARU deale r for assistance.
6. Confirm that all warning and indicator lights have
gone off after the engine has started. The fuel injection
system automatically lowers the idle speed as the en-
gine warms up.
NOTE (Turbo models)
The engine may be difficult to start when the bat-

7-10
Starting and operating
tery has been disconnected and reconnected (for
maintenance or other purposes). This difficulty is
caused by the electronically controlled throttle’s
self-diagnosis function. To
overcome it, keep the
ignition switch in the “O N” position for approxi-
mately 10 seconds before starting the engine. „ Automatic transmission vehicle
If you restart the engine while the vehicle is
moving, shift the selector lever into the “N” po-
sition. Do not attempt to place the selector lever
of a moving vehicle into the “P” position.
1. Apply the parking brake.
2. Turn off unnecessary lights and accessories.
3. Shift the selector lever to the “P” or “N” position
(preferably “P” position). Th e starter will only operate
when the select lever is at the “P” or “N” position.
4. Turn the ignition switch to the “ON” position and
check the operation of the warning and indicator lights.
Refer to the “Warning and indicator lights” section
(chapter 3).
5. Turn the ignition switch to the “START” position without
depressing the accelerator pedal. Release
the key immediately after the engine has started.
If the engine does not start, try the following.
1) Turn the ignition switch to the “OFF” position and
wait for at least 10 seconds. After checking that the
parking brake is firmly set, turn the ignition switch to
the “START” position while depressing the acceler-
ator pedal slightly (about a quarter of the full stroke).
Release the accelerator pedal as soon as the en-
gine starts.
2) If this fails to start the engine, turn the ignition
switch back to the “OFF” position and wait for at
least 10 seconds. Then fully depress the accelerator
pedal and turn the ignition switch to the “START”
position. If the engine starts, quickly release the ac-
celerator pedal.
3) If this fails to start the engine, turn the ignition
switch again to the “OFF” position. After waiting for 10 seconds or longer, turn the ignition switch to the
“START” position without depressing the accelera-
tor pedal.
4) If the engine still refuses to start, contact your
nearest SUBARU dealer for assistance.
6. Confirm that all warning and indicator lights have
gone out after the engine ha s started. The fuel injec-
tion system automatically lowers the idle speed as the
engine warms up.

11 - 4
Maintenance and service
the materials in the vehicle may be hazardous if
improperly used or handled, for example, bat-tery acid. y
Your vehicle should only be serviced by per-
sons fully competent to do so. Serious person-
al injury may result to persons not experienced
in servicing vehicles. y Always use the proper tools and make certain
that they are well maintained. y Never get under the vehicle supported only
by a jack. Always use a safety stands to sup-
port the vehicle. y Never keep the engine running in a poorly
ventilated area, such as a garage or other
closed areas. y Do not smoke or allow open flames around
the fuel or battery. This will cause a fire. y Because the fuel system is under pressure,
replacement of the fuel filter should be per-
formed only by your SUBARU dealer.y Wear adequate eye protection to guard
against getting oil or fl uids in your eyes. If
something does get in your eyes, thoroughly
wash them out with clean water. y Do not tamper with the wiring of the SRS air-
bag system or seatbelt pretensioner system, or
attempt to take its connectors apart, as that may activate the system or it can render it inop-
erative. The wiring an
d connectors of these
systems are yellow for easy identification. NEV-
ER use a circuit tester for these wiring.
If your SRS airbag or seatbelt pretensioner
needs service, consult your nearest SUBARU
dealer.
„ Before checking or servicing in the en-
gine compartment
yAlways stop the engine and set the parking
brake firmly to prevent the vehicle from mov-
ing. y Always let the engine cool down. Engine
parts become very hot when the engine is run-
ning and remain hot for some time after the en-
gine is stopped. y Do not spill engine oil, engine coolant, brake
fluid or any other fluid on hot engine compo-
nents. This may cause a fire.y Always remove the key from the ignition
switch. When the ignition switch is in the “ON”
position, the cooling fan may operate suddenly

12-5
Specifications
– CONTINUED –
Fuses and circuits „Fuse panel located behind the coin tray
19
18
17
16
20
15
14
12
11
10 9
8
7
6
5
4
3
2
1
13
UBC001BB
Fuse panelFuse ratingCircuit
115Ay
Heater fan
215AyHeater fan
315AyPower door lock
y Keyless entry
420AyMirror heater
y Cigarette lighter
y Remote controlled rear
view mirrors
510AyTail light
y Parking light
615AySRS airbag
715AyFront fog light
830AyABS solenoid
915AyRadio
y Clock
1015AyTrailer
1115AyEngine ignition system
y SRS airbag