2006 SUBARU BAJA License plate

8-21
Driving tips
– CONTINUED –
tributing hitch.
The trailer hitch is designed to tow a Class 1 rated
load. A maximum of 2,400 lbs (1,087 kg) gross trailer
weight and a maximum of 200 lbs (90 kg) gross
tongue weight are permissible for the trailer hitch.
When you tow a trailer, follow the instructions in the
next section “Trailer towing”. „ Connecting a trailer
The license plate bracket will hit the hitch ball
and may be damaged if the tailgate is opened
and the license plate bracket is at the lowered/
open position. Close the tailgate and return the
license plate bracket to its normal position
flush against the tailgate itself whenever you
tow a trailer or whenever a trailer is hitched to
the vehicle.
1. Before connecting the ball mount to the hitch re-
ceiver, close the tailgate and return the license plate
bracket to its normal retracted position up against the
tailgate. Refer to “License plate bracket” under the
heading “Tailgate” in chapter 2 for more information on
the function of the license plate bracket.
2. Remove the receiver cover from the hitch receiver
tube. Then insert the ball mount into the hitch receiver
tube.
UB8047BA

8-24
Driving tips
Hitch harness connector
9. Connect the hitch wire harness’s black four-pin
wire connector to the towing trailer’s wire harness.
10.Confirm proper function of the hitch wire harness
by individually activating the brake, right turn signal,
left turn signal, stop, and parking lights on the trailer.
NOTE
Always disconnect the trailer wire harness before
launching or retrieving a watercraft. „
When you do not tow a trailer
Remove the ball mount from the hitch receiver
tube when the tailgate is open and the bed ex-
tender is used. The rear license plate will not be
visible because the license plate bracket can
not be used at the lowered/open position when
the ball mount is connected.
In addition, the license plate bracket will hit the
hitch ball and may be da maged if the tailgate is
opened and the license plate bracket is at the
lowered/open position.
y Remove the ball mount from the hitch receiver tube
and insert the receiver cover onto the hitch receiver tube.y Place the dust cap over the four-pin connector of the
hitch wire harness to protect against possible damage.y Occasionally lubricate terminals of the four-pin con-
nector using the terminal grease, and cover with the
attached rubber cap.
HS8015BA

11 - 2
Maintenance and service
Types of tires .................................................... 11-46
Tire inspection .................................................. 11-47
Tire pressures and wear .................................. 11-47
Wheel balance ................................................... 11-50
Wear indicators ................................................. 11-50
Tire rotation ....................................................... 11-51
Tire replacement ............................................... 11-51
Wheel replacement ........................................... 11-52
Aluminum wheels ......................................... 11-53
Windshield washer fluid .............................. 11-53
Replacement of windshield wiper blades .. 11-55
Battery ........................................................... 11-58
Fuses ............................................................. 11-59
Main fuse ....................................................... 11-61
Installation of accessories .......................... 11-62
Replacing bulbs ............................................ 11-63 Headlight ........................................................... 11-66
Front fog light ................................................... 11-70
Front turn signal light, parking light and side marker light .................................................... 11-71
Rear combination lights ................................... 11-72
Tail light (on the tailgate) ................................. 11-74
License plate light ............................................ 11-76
Map light, dome light and door step light ...... 11-78
High mount stop and cargo light assembly ... 11-79
Sport activity lights (if equipped) .................... 11-81

11 - 6 6
Maintenance and service
Replace any bulb only with a new bulb of the
specified wattage. Using a bulb of different
wattage could result in a fire.
„ Headlight
„Headlights
„ Replacing bulbs
„ Headlight
Halogen headlight bulbs become very hot while
in use. If you touch the bulb surface with bare
hands or greasy gloves, finger prints or grease
on the bulb surface will develop into hot spots
and cause the bulb to break. If there are finger
prints or grease on the bulb surface, wipe them
away with a soft cloth moistened with alcohol.
NOTE
If headlight aiming is required, consult your
SUBARU dealer for proper adjustment of the head-
light aim.
Wattage Bulb No.
8) License plate light 12V-5W 168
9) Cargo light 12V-13W 912
10) High mount stop light 12V-13W 912
11) Backup light 12V-21W 7440
12) Brake rear turn signal/ tail light 12V-21/ 5W7443
13) Tail light 12V-5W 168
14) Sports activity lights 12V-55W H3

11 - 7 6
Maintenance and service
„
License plate light„
License plate light
„ Replacing bulbs
„ License plate light0
1. Push two release buttons and pull the license plate
bracket up until it clicks. 2. Remove the two cove
r installation screws.
3. Push the license plate bracket back to the original position.
UBB096BA
UBB097BA

11 -7 7
Maintenance and service
– CONTINUED –
4. Remove the screw from the side of the cover.
5. Remove the cover. 6. Remove the bulb socket from the license plate
bracket by turning it counterclockwise.
7. Pull the bulb out of the socket.
8. Install a new bulb in the socket by pushing it.
9. Install the bulb socket into the license plate bracket.
10.Install the covers by reversing procedures for re-moval.
UBB092BAUBB093BA

12-8
Specifications
Bulb chart
Description Wattage Bulb No.
Headlight
S models 12V-65/55W 9007 (HB5)
Except S modelsLow beam 12V-55W H1
High beam 12V-60W 9005 (HB3)
Front turn signal light 12V-27W 1156NA (Amber)
Spot light 12V-8W –
Dome light 12V-8W –
Door step light 12V-3.4W –
Parking and front
side marker light 12V-27/8W 1157NA
(Amber)
Front fog light 12V-51W 9006 (HB4)
Backup light 12V-21W 7440
High mount stop light 12V-13W 912
Brake·Rear turn sig-
nal light/Tail light 12V-21/5W 7443
Rear finisher light 12V-5W 168
License plate light 12V-5W 168
Cargo light 12V-13W 912
Sports activity light 12V-55W H3

14-5
Index
Gauge ............................................................. 3-8
Requirements ................................................. 7-2
Fuses ............................................................... 11-59
Fuses and circuits ............................................. 12-5 G
GAWR (Gross Axle Weight Rating) ................... 8-19
Glove box ............................................................ 6-5
GVWR (Gross Vehicle Weight Rating) .............. 8-19 H
Hard bed cover .................................................. 6-24
Hazard warning flasher ....... ................................ 3-6
Head restraint adjustment (Fro nt) ........................ 1-6
Headlight flasher ................. .............................. 3-21
Headlights ............. ................................. 3-20, 11-66
Heater operation .... .......................................... .... 4-7
High beam indicator light ................................... 3-18
High mount stop and cargo light assembly ...... 11-79
Horn ................................................................... 3-35
Hose and connections ......... ............................ 11-18
I
Ignition switch ...................................................... 3-2
Illuminated entry .................................................. 2-9
Illumination brightness contro l ........................... 3-23 Indicator light
High beam .................................................... 3-18
Selector lever position .................................. 3-17
Turn signal .................................................... 3-17
Inside mirror ...................................................... 3-30
Interior light .......................................................... 6-2 J
Jack and tools ..................................................... 9-3
Jump starting ..................................................... 9-18 K Key Interlock release ............................................. 3-5
Number ........................................................... 2-2
Reminder chime ............................................. 3-4
Keys .................................................................... 2-2 L
Leather seat materials ....................................... 10-7
License plate bracket ........................................ 2-30
License plate light ............................................ 11-76
Light control switch ............................................ 3-19
Limited slip differential (LSD ) ............................ 7-30
Loading your vehicle ......................................... 8-17
Lower tether anchorages ................................... 1-40