
Cockpit
64Traction control system (TCS)*
The traction control system prevents the driven wheels from 
spinning when the vehicle is acceleratingThe warning lamp lights up when the ignition is switched on and should turn 
out after about 2 seconds.
When the TCS is operating while drivi ng, the warning lamp flashes. If the 
system is deactivated or if there is any fault in the same, the warning lamp will 
remain lit.
It will also come on if a fault should occur in the ABS because the TCS oper-
ates in conjunction with the ABS. For further information see  ⇒page 145, 
“Brakes”.Electronic stabilisation program (ESP)* 
 
This warning lamp monitors the electronic stabilisation 
program.
This program includes the ABS, EDL and TCS.
The warning lamp 
 has the following functions:
•
It will light for about 2 seconds when the ignition is switched on while a 
test of the function is carried out.
•
It flashes when the ESP is activated when driving.
•
It will light up continuously if there is a malfunction in the ESP.
•
It will light up continuously if the ESP is switched off.
•
It will also come on if a fault should occur in the ABS because the ESP 
operates in conjunction with the ABS.
If the ESP warning lamp 
 lights up and stays on after the engine is started, 
this may mean that the control system has temporarily switched off the ESP.  In this case the ESP can be reactivated by switching the ignition off and then 
on again. If the warning lamp goes out, this means the system is fully 
functional.
Soot accumulation in the diesel engine particulate filter* 
The warning lamp lights up when the ignition is switched on.
If the symbol 
 lights up, soot has built up in the diesel engine particulate 
filter due to continuous short trips. In  this case, drive the vehicle at a constant 
speed of at least 60 km/h (with and engine speed of about 1400 rpm) for 
about 10 minutes. The increase in temperature generated may burn the accu-
mulated soot in the filter. Once this  is done, the symbol should disappear.
If the symbol  is not turned off, drive the vehicle to a qualified workshop 
and have the fault repaired.
For more information on the diesel particulate filter  ⇒page 151.
WARNING
•
The diesel engine particulate filter may reach extremely high tempera-
tures; it should not enter into contact with flammable materials under-
neath the vehicle. Failure to comply could result in fire.Caution
Vehicles equipped with a diesel engine particulate filter must not be refuelled 
using biodiesel (RME), given that the fuel system may be damaged.
ibiza_angles_0706_DEF  Seite 64  Freitag, 1. September 2006  1:18 13 

Driving and the environment151
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
– Never tow the vehicle to start it, use jump leads if necessary 
⇒ page 225.If you notice misfiring, uneven running  or loss of power when the vehicle is 
moving, reduce speed immediately and have the vehicle inspected at the 
nearest qualified workshop. In general,  the exhaust warning lamp will light 
up when any of the described symptoms occur  ⇒page 58. If this happens, 
unburnt fuel can enter the exhaust system and escape into the environment. 
The catalytic converter can also be damaged by overheating.
WARNING
The catalytic converter reaches very high temperatures! Fire hazard!•
Never park where the catalytic converter could come into contact with 
dry grass or inflammable materials under the vehicle.
•
Do not apply additional underseal or anti-corrosion coatings to the 
exhaust pipes, catalytic converter or the heat shields on the exhaust 
system. These materials could catch fire when the vehicle is driven.Caution
Never fully drain the fuel tank, in this case, the irregularity of the fuel supply 
may cause ignition problems. This allow s unburnt fuel to enter the exhaust 
system, which could cause overheating and damage the catalytic converter.
For the sake of the environment
Even when the emission control system is working perfectly, there may be a 
smell of sulphur from the exhaust unde r some conditions. This depends on 
the sulphur content of the fuel used.  Quite often the problem can be reme-
died by changing to another brand of fuel.
Diesel engine particulate filter*
The diesel engine particulate filter eliminates soot produced 
by burning diesel.The diesel engine dust filter eliminates most of the soot from the exhaust gas 
system. The soot particulates accumulate  in the filter where they are regularly 
burned. In order to facilitate this process, occasional journeys at speeds of 
more than 60 kmh should be made. If the vehicle is only used for short trips 
then the soot will build up in the particulate filter.
WARNING
•
The diesel engine particulate filter may reach extremely high tempera-
tures; it should not enter into contact with flammable materials under-
neath the vehicle. Failure to comply could result in fire.Caution
Vehicles equipped with a diesel engine particulate filter must not be refuelled 
using biodiesel (RME), given that the fuel system may be damaged.Driving abroadNotesFor driving abroad, the following must be taken into consideration:•
For vehicles fitted with a catalytic converter ensure that unleaded petrol is 
available for the journey. See the chap ter “Refuelling”. Automobile organisa-
tions will have information about service station networks selling unleaded 
fuel.
ibiza_angles_0706_DEF  Seite 151  Freitag, 1. September 2006  1:18 13 

Checking and refilling levels175
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
DieselDiesel*Diesel fuel must correspond to DIN EN 590 (EN = “European standard”). It 
must have a cetane number (CN) of at  least 51. The cetane number indicates 
the ignition quality of the diesel fuel.
Notes on filling with fuel  ⇒page 173.RME fuel*The biodiesel fuel must comply wit h the DIN EN 14.214 (FAME) Standard.•
Biodiesel is a methylester obtained from rapeseed oil.
•
DIN is a German abbreviation for “Deutsches  Institut für  Normung e.V.”, 
the German standards institute.
•
EN means  European  Norm.
•
FAME is the English abbreviation “ Fatty  Acid  Methyl  Ester”.
Your Authorised Service Centre or au tomobile association will be able to 
advise on where you can obtain RME biodiesel fuel.
Your Authorised Service Centre can also be consulted to know if the vehicle 
has been prepared for biodiesel use.
Things to note about RME fuel (biodiesel)
•
The performance of a vehicle using biodiesel maybe somewhat reduced.
•
Fuel consumption of a vehicle using biodiesel may be slightly higher.
•
RME fuel can be used in winter at  temperatures down to approx. -10°C.
•
At outside temperatures below -10°C, we recommend using winter diesel 
fuel.
Caution
•
RME fuel can damage the fuel system in vehicles that are not suitably 
adjusted.
•
If you decide to use biodiesel in your vehicle, please use only RME fuel 
which is DIN E 14,214 compliant.
•
If you use biodiesel that does not me et the required standard, the fuel 
filter could become clogged.Note
•
In case of low exterior temperatures and a biodiesel fuel percentage of 
higher than 50%, an increase in gas emission may occur during operation of 
the independent heating.
•
The fuel filter may become clogged when fuel is changed to biodiesel. For 
this reason, we recommend that, about every 300 or 400 km, following a fuel 
change, also change the fuel filter. Also. note the instructions in the inspec-
tion and maintenance plan.
•
If the vehicle is to remain parked for more than about two weeks, we 
recommend filling the fuel tank with  biodiesel and driving about 50 km in 
order to avoid damage to the injection system.
Winter driving
Diesel can thicken in winter.Winter-grade diesel
When using “summer-grade diesel fuel”, difficulties may be experienced at 
sub-zero temperatures because the fuel thickens due to wax separation. For 
this reason, “winter-grade diesel fuel” is available in some countries during 
the cold months. It can be used at temperatures as low as -22°C.
ibiza_angles_0706_DEF  Seite 175  Freitag, 1. September 2006  1:18 13 

Checking and refilling levels
176In countries with different climatic conditions the diesel fuel sold generally 
has different temperature characteristics. Check with an Authorised Service 
Centre or filling stations in the country concerned regarding the type of diesel 
fuels available.
Filter pre-heater
Your vehicle is fitted with a fuel filter pre-heater, making it well equipped for 
operation in winter. This ensures that the fuel system remains operational to 
approx. -24°C, provided you use winter-grade diesel which is safe to -15°C.
However, if the fuel has waxed to such an extent that the engine will not start 
at temperatures of under -24°C, simply place the vehicle in a warm place for 
a while.
Caution
Do not mix fuel additives (“thinners”, or similar additives) with diesel fuel.Working in the engine compartmentSafety instructions on working in the engine compartment
Any work carried out in the engine compartment or on the 
engine must be carried out cautiously.Before starting any work on the engine or in the engine compart-
ment:
1.  Switch off the engine and remove the key from the ignition.
2. Apply the handbrake.
3.  Move the gear stick to neutral or the selector lever to position P. 4.  Wait for the engine to cool down.
5.  Keep children away from the vehicle.
6. Raise the bonnet 
⇒page 178.
You should not do any work in the engine compartment unless you know 
exactly how to carry out the jobs and have the correct tools! Have the work 
carried out by a qualified workshop if you are uncertain.
All service fluids and consumables, e.g.  coolant, engine oil, spark plugs and 
batteries, are being constantly developed . SEAT provides a constant flow of 
information to the Authorised Service  Centres concerning modifications. For 
this reason we recommend that you have service fluids and consumables 
replaced by an Authorised Service Centre. Please observe the relevant 
instructions  ⇒page 169. The engine compartmen t of any motor vehicle is a 
hazardous area  ⇒.
WARNING
All work on the engine or in the engine compartment, e.g. checking and 
refilling fluids, involves the danger of injury and scalding as well as the risk 
of accident or fire.•
Never open the bonnet if you see steam, smoke or coolant escaping 
from the engine compartment. Otherwise, there is a risk of sustaining 
burns. Wait until no more steam or  coolant is emitted, then allow the 
engine to cool before carefully opening the bonnet.
•
Switch off the engine and remove the key from the ignition.
•
Apply the handbrake and move the gear stick to neutral or selector 
lever to position P.
•
Keep children away from the vehicle.
•
Never touch hot engine parts.  There is a risk of burns.
•
Never spill liquids on a hot engine or  on a hot exhaust gas system. This 
is a fire hazard.
ibiza_angles_0706_DEF  Seite 176  Freitag, 1. September 2006  1:18 13 

Technical Data
240Trailer weights
Engine oil capacityPetrol engine 1.4 litre 63 kW (86 bhp)General engine data
Performance figures With no brakes, gradients up to 12%
500
With brakes, gradients up to 12% 800
Approximate engine oil capacity with oil filter change 3,2 litres
Power output in kW (bhp) rpm 63 (86)/ 5000
Maximum torque in Nm at rpm 132/ 3800
No. of cylinders, capacity in cm
3
4/ 1390
Compression  10,5 +/- 0,3
Fuel Super 95 RON
a)/Normal 91 RON
b)
a)Research- Octane- Number = Measure of the predetonation power of the petrol.b)Slight power lossMaximum speed in km/h 180
Acceleration from 0-80 km/h in sec. 8,1
Acceleration from 0-100 km/h in sec. 11,9
ibiza_angles_0706_DEF  Seite 240  Freitag, 1. September 2006  1:18 13 

Technical Data241
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
Weights
Trailer weights
Engine oil capacity
Petrol engine 1.4 litre 55 kW (75 hp). AutomaticGeneral engine data
3 doors
5 doors
Gross vehicle weight in kg 15421567
Weight in working order (with driver) in kg 11031128
Gross axle weight, front in kg 815820
Gross axle weight, rear in kg 775795
Permitted roof load in kg 7575
With no brakes, gradients up to 12% 600
With brakes, gradients up to 12% 1000
Approximate engine oil capacity with oil filter change 3,2 litres
Power output in kW (bhp) rpm 55 (75)/ 5000
Maximum torque in Nm at rpm 126/ 3800
No. of cylinders, capacity in cm
3
4/ 1390
Compression  10,5
Fuel Super 95 RON
a)/Normal 91 RON
b)
a)Research- Octane- Number = Measure of the predetonation power of the petrol.
ibiza_angles_0706_DEF  Seite 241  Freitag, 1. September 2006  1:18 13
b)Slight power loss 

Technical Data
244Trailer weights
Engine oil capacityPetrol engine 1.6 litre 77 kW (105 bhp)General engine data
Performance figures With no brakes, gradients up to 12%
500
With brakes, gradients up to 12% 1000
Approximate engine oil capacity with oil filter change 3,5 litres
Power output in kW (bhp) rpm 77 (105)/5 600
Maximum torque in Nm at rpm 153/ 3800
No. of cylinders, capacity in cm
3
4/ 1598
Compression  10,5+/- 0,2
Fuel 95 super RON
a)
a)Research- Octane- Number = Measure of the predetonation power of the petrol.Maximum speed in km/h 192
Acceleration from 0-80 km/h in sec. 7,2
Acceleration from 0-100 km/h in sec. 11,0
ibiza_angles_0706_DEF  Seite 244  Freitag, 1. September 2006  1:18 13 

Technical Data245
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l  D a t a
Weights
Trailer weights
Engine oil capacity
Petrol engine 1.8 litre 110 kW (150 bhp)General engine data
3 doors
5 doors
Gross vehicle weight in kg 15641589
Weight in working order (with driver) in kg 11441169
Gross axle weight, front in kg 825830
Gross axle weight, rear in kg 783800
Permitted roof load in kg 7575
With no brakes, gradients up to 12% 550
With brakes, gradients up to 12% 1000
Approximate engine oil capacity with oil filter change 4,0 litres
Power output in kW (bhp) rpm 110 (150)/ 5500
Maximum torque in Nm at rpm 220/ 1450-4500
No. of cylinders, capacity in cm
3
4/ 1781
Compression  9,5 ± 0,5
Fuel Super 95 RON
a)/Normal 91 RON
b)
a)Research- Octane- Number = Measure of the predetonation power of the petrol.
ibiza_angles_0706_DEF  Seite 245  Freitag, 1. September 2006  1:18 13
b)Slight power loss