2006 Seat Ateca XL light

If and when
244Some of the electrical items listed in the table are only fitted on certain
models or are optional extras.
Please note that the above list, while corr ect at the time of printing, is subject
to alterations. If discrepancies should occur, please refer to the sticker on the
inside of the fuse cover for the correct information for your model. 45
Electric windows, front 30
46 Rear electric windows 30
47 Engine (Gauge, petrol relay) 15
48 Convenience controls 20
49 Heater controls 40
50 Heated seats 30
51 Sunroof 20
52 Headlight washer system 20
53 Kit (guided solution) trailer coupling 20
54 Taxi (taximeter supply) 5
55 Kit (guided solution) trailer coupling 20
56 Taxi (radio supply) 15
57 Vacant
58 Central locking control unit 30
Number
Electrical equipment Amperes
AlteaXL_ingles_02_06 Seite 244 Dienstag, 1. August 2006 11:11 11

If and when
246
19 Clean 30
20 Vacant
21 Lambda probe 15
22 Brake pedal, speed sensor 5
23 Engine 1.6, main relay (relay n° 100)
5
T 71 diesel EGR 10
2.0 D2L High-pressure fuel pump 15
24 ARF, change valve 10
25 Right lighting 40
26 Left lighting 40
1.6 SLP engine 40
1.9 TDI Glow plug relay 50
28 KL15 40
29 Electric windows (front and back)
50
Electric windows (front) 30
30 X - relief relay 40
Number
Electrical equipment Amperes
AlteaXL_ingles_02_06 Seite 246 Dienstag, 1. August 2006 11:11 11

If and when247
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Position in engine compartment: side boxFuses
Some of the electrical items listed in the table are only fitted on certain
models or are optional extras.
Please note that the above list, while correct at the time of printing, is subject
to alterations.Bulb changeGeneral notesBefore changing any bulb first turn off the equipment concerned.
Do not touch the bulb glass. Fingerprints vaporise in the heat, causing a
reduction in the bulb life and condensation on the mirror surface, thus
reducing efficiency. A bulb should only be replaced by one of the same type. The type is inscribed
on the bulb, either on the glass part or on the base.
It is highly recommended to keep a box of spare bulbs in the vehicle. At the
very least, the bulbs that most affect road safety should have spares in the
vehicle.
Main headlights
Dipped beam - H7
Main beam - H1
Position - W5W
Turn signals - PY21W
Number
Electrical equipment Amperes
B1 Alternator < 140 W
150
Alternator > 140 W 200
C1 Power steering 80
D1 Multi-terminal voltage supply “30”. Internal fuse box 100
E1 Ventilator > 500 W / Ventilator < 500 W 80/50
F1 PTCs (Supplementary electrical heating using air) 100
G1 Trailer fuse voltage supply in internal fuse box 50
H1 Central locking control unit (4F8 with autolock)
AlteaXL_ingles_02_06 Seite 247 Dienstag, 1. August 2006 11:11 11

If and when
248Xenon headlamps
22)/self-adjusting
Dipped and main - D1S23)
Flasher and additional main - H1
Position W5W
Turn signals PY21W
Fog lights
Fog lights - H3
Fixed rear light
Stop/Position - P21W
24)
Turn signals - P21W
Rear tailgate light unit
Fog lamp (driver’s side) - P21W
Reversing light (passenger side) - P21W
Position - W5W
Indicator
Indicator - W5W
Registration plate light
Registration plate light - C5W
Note
•
Due to the difficulty in accessing the lamps, any replacement work should
be done by a SEAT dealer. However, the following is a description of how to
change the bulbs except for the fog lights and interior bulbs.
Main headlight lamps
Turn signals
Dipped headlights
Main beam headlights
Side lights
22)On this type of headlight, the bulb changes must be made by the SEAT dealer, given
that complex elements must be removed from the vehicle and a reset must be made
on the automatic control system incorporated.23)The Xenon bulbs discharge 2.5 times the light flux and have an average lifespan of 5
times more than that of halo gen bulbs, this means that, except due to unusual circum-
stances, there is no need to change the bulbs for the whole life of the vehicle.24)Electronically controlled single filament bulb for Stop/side bulbs. If the bulb blows it
will not work in either position or Stop position
Fig. 178 Main headlight
lamps
AAABACAD
AlteaXL_ingles_02_06 Seite 248 Dienstag, 1. August 2006 11:11 11

If and when249
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Turn signal lamps–Raise the bonnet.
– Rotate the lamp holder ⇒fig. 179 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam lights– Raise the bonnet
Fig. 179 Turn signal
lamps
AA
Fig. 180 Dipped head-
lightsFig. 181 Dipped head-
lights
AlteaXL_ingles_02_06 Seite 249 Dienstag, 1. August 2006 11:11 11

If and when
250
– Remove the loops ⇒page 249, fig. 180 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 249, fig. 181 from the bulb.
– Disengage the retainer spring ⇒ page 249, fig. 181 pressing
inwards and to the right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam lights
–Raise the bonnet.
– Remove the cover ⇒fig. 182 by pulling on this.
– Remove the connector ⇒fig. 183 from the bulb.
– Press the spring ⇒fig. 183 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2
A3
Fig. 182 Main beam
headlights
Fig. 183 Main beam
headlights
AC
A1
A2
AlteaXL_ingles_02_06 Seite 250 Dienstag, 1. August 2006 11:11 11

If and when251
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side lights–Raise the bonnet.
– Remove the cover ⇒fig. 184 by pulling on this. – Extract the lamp holder
⇒fig. 185 outwards.
– Replace the bulb by pulling this out and inserting the replace- ment.
– Installation is done in the reverse order.
Rear lights•
On the body
- -Indicator, side and brake light
•
On the tailgate
- Left hand side: side and foglight.
- Right hand side: side and reverse light.
Fig. 184 Side lightsFig. 185 Side lights
AD
A1
AlteaXL_ingles_02_06 Seite 251 Dienstag, 1. August 2006 11:11 11

If and when
252Indicator, side and brake lights on the bodywork– Open the cover of the luggage compartment lateral panel
⇒fig. 186. –Turn the lampholder anti-clockwise ⇒
fig. 187.
– Extract the failed bulb and change it for a new one.
– To refit follow the steps in reverse order, taking special care when fitting the lamp holder.
Fig. 186 Lights on
vehicle bodyFig. 187 Lights on
vehicle body
AlteaXL_ingles_02_06 Seite 252 Dienstag, 1. August 2006 11:11 11