2006 SAAB 9-2X maintenance

Maintenance and service
11 - 4 1
11
– CONTINUED –
FusesThe fuses are designed to melt during an
overload to prevent damage to the wiring
harness and electrical equipment. The
fuses are located in two fuse boxes.
One is located under the instrument panel
behind the coin tray on the driver’s seat
side.To remove the coin tray, open the cover
and pull the coin tray out.
The other one is housed in the engine
compartment.The spare fuses are stored in the main
fuse box cover in the engine compart-
ment.
The fuse puller is stored in the main fuse
box in the engine compartment.
Never replace a fuse with one hav-
ing a higher rating or with material
other than a fuse because serious
damage or a fire could result.
B00172
B00173B00481
B00476B00477
A1910BE-A-GSAAB.book Page 41 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 4 2
Maintenance and service
1) Good
2) BlownIf any lights, accessories or other electri-
cal controls do not operate, inspect the
corresponding fuse. If a fuse has blown,
replace it.
1. Turn the ignition switch to the “LOCK”
position and turn off all electrical accesso-
ries.
2. Remove the cover.
3. Determine which fuse may be blown.
The back side of each fuse box cover and
the “Fuses and circuits” section in chapter
12 in this manual show the circuit for each
fuse.4. Pull out the fuse with the fuse puller.
5. Inspect the fuse. If it has blown, re-
place it with a spare fuse of the same rat-
ing.
6. If the same fuse blows again, this indi-
cates that its system has a problem. Con-
tact your Saab dealer for repairs.
Main fuseMain fuse boxThe main fuses are designed to melt dur-
ing an overload to prevent damage to the
wiring harness and electrical equipment.
Check the main fuses if any electrical
component fails to operate (except the
starter motor) and other fuses are good. A
melted main fuse must be replaced. Use
only replacements with the same speci-
fied rating as the melted main fuse. If a
main fuse blows after it is replaced, have
the electrical system checked by your
nearest Saab dealer.
12
B00338
600160
B00481
A1910BE-A-GSAAB.book Page 42 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 4 3
11
– CONTINUED –
Installation of accessoriesAlways consult your Saab dealer before
installing fog lights or any other electrical
equipment in your vehicle. Such accesso-
ries may cause the electronic system to
malfunction if they are incorrectly installed
or if they are not suited for the vehicle.
A1910BE-A-GSAAB.book Page 43 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 4 4
Maintenance and service
Replacing bulbs
45
876 1213 14 123 9 10 11
B00482
A1910BE-A-GSAAB.book Page 44 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 4 5
– CONTINUED –
11
Wattage Bulb No.
1) Low beam head light
Premium Package
vehicles12V-35W D2R
Others 12V-55W H1
2) High beam head light 12V-60W 9005 (HB3)
3) Front side marker light 12V-5W W5W
4) Spot light 12V-8W –
5) Room light 12V-8W –
6) Front turn signal 12V-21W (Amber) WY21W (7440A)
7) Parking light 12V-5W W5W
8) Front fog light 12V-57W 9006 (HB4)
9) High mount stop light 12V-1.3W LED
10) Rear turn signal light 12V-21W (Amber) WY21W (7440A)
11) Cargo area light 12V-5W –
12) Brake/tail light 12V-21/5W W21/5W (7443)
13) Backup light 12V-16W W16W (921)
14) License plate light 12V-5W W5W
Replace any bulb only with a new
bulb of the specified wattage. Using
a bulb of different wattage could re-
sult in a fire.
A1910BE-A-GSAAB.book Page 45 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 4 6
Maintenance and service

HID headlight bulbs
3

Halogen headlight bulbs
3
NOTE
If headlight aiming is required, con-
sult your Saab dealer for proper adjust-
ment of the headlight aim.

It may be difficult to replace the
bulbs. Have your Saab dealer replace
the bulbs if necessary.
Right-hand low beam light bulb
Non-turbo model
1) Air intake duct
Turbo model
High-intensity-discharge (HID) bulbs
are used for the low beams of the
headlights. These HID bulbs use an
extremely high voltage. To avoid the
risk of an electric shock and result-
ing serious injury, you should not
attempt to replace them. Neither
should you attempt to replace the
high-beam bulbs, remove/refit the
headlight assemblies, or remove
any headlight-assembly compo-
nents. For replacement of the head-
light bulbs (low-beam and high-
beam), removal and installation of
the headlight assemblies, and re-
moval of headlight-assembly com-
ponents, contact your Saab dealer.
Ask your Saab dealer to check
whether your vehicle is equipped
with HID headlights.
Halogen headlight bulbs become
very hot while in use. If you touch
the bulb surface with bare hands or
greasy gloves, finger prints or
grease on the bulb surface will de-
velop into hot spots and cause the
bulb to break. If there are finger
prints or grease on the bulb surface,
wipe them away with a soft cloth
moistened with alcohol.
Ask your Saab dealer to check
whether your vehicle is equipped
with halogen headlights.
B00483
1
B00484
A1910BE-A-GSAAB.book Page 46 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 4 7
11
– CONTINUED –
1. Remove the air intake duct mounting
bolt, then remove the air intake duct.
2. Remove the bulb cover by turning it
counterclockwise.3. Push the retainer spring in the direction
of the arrow to remove it from the hook.
4. Pull the bulb out of the electrical con-
nector. Replace the bulb with a new one.
5. Set the retainer spring securely.
6. Reconnect the electrical connector.7. Install the bulb cover.

Left-hand low beam light bulb

High beam light bulbs
0
1. Remove the bulb from the headlight
assembly by turning it counterclockwise.
B00485B00486
700092B00488
Replacement of the left-hand low
beam light bulb requires removal of
the battery and is thus dangerous. It
must be performed by a Saab deal-
er.
B00489
A1910BE-A-GSAAB.book Page 47 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 4 8
Maintenance and service
2. Remove the electrical connector from
the bulb.
3. Replace the bulb with a new one.
4. Reconnect the electrical connector. At
this time, be careful not to touch the bulb
surface.
5. Install the bulb in the headlight assem-
bly by turning it clockwise until it clicks.

Parking light
Right-hand sideNon-turbo model
1) Air intake ductTurbo model
1. Remove the air intake duct mounting
bolt, then remove the air intake duct.
2. Remove the bulb cover by turning it
counterclockwise.
700093
B00483
1
B00484B00485
A1910BE-A-GSAAB.book Page 48 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com