2006 SAAB 9-2X warning

Seat, seatbelt and SRS airbags
1-53
1
– CONTINUED –

Examples of the types of accidents in which the SRS side airbag will ba-
sically not deploy.1) The vehicle is involved in a frontal colli-
sion with another vehicle (moving or sta-
tionary).
2) The vehicle is struck from behind.
The SRS side airbag is basically not de-
signed to deploy if the vehicle is involved
in a frontal collision or is struck from be-
hind. Examples of such accidents are il-
lustrated.1) First impact
2) Second impactIn an accident where the vehicle is struck
from the side more than once, the SRS
side airbag deploys only once.
Example: In the case of a double side im-
pact collision, first with one vehicle and
immediately followed by another from the
same direction, once the SRS side airbag
is activated on the first impact, it will not be
activated on the second.

SRS airbag system monitorsA diagnostic system continually monitors
the readiness of the SRS airbag system
(including front seatbelt pretensioners)
while the vehicle is being driven. The SRS
airbag system warning light “AIRBAG” will
show normal system operation by lighting
for approximately 6 seconds when the ig-
nition switch is turned to the “ON” position.
The following components are monitored
by the indicator:

Front sub sensor (Right-hand side)

Front sub sensor (Left-hand side)

Airbag control module (including impact
sensors)

Frontal airbag module (Driver’s side)

Frontal airbag module (Front passen-
ger’s side)
1
2
100716
2
1
100629
100291
A1910BE-A-GSAAB.book Page 53 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

1-54
Seat, seatbelt and SRS airbags

Side airbag sensor (Center pillar right-
hand side)

Side airbag sensor (Center pillar left-
hand side)

Side airbag module (Driver’s side)

Side airbag module (Front passenger’s
side)

Seatbelt pretensioner (Driver’s side)

Seatbelt pretensioner (Front passen-
ger’s side)

Seatbelt buckle switch (Driver’s side)

Seatbelt buckle switch (Front passen-
ger’s side)

Driver’s seat position sensor

Front passenger’s seatbelt tension sen-
sor

Front passenger’s occupant detection
system weight sensor

Front passenger’s occupant detection
control module

Front passenger’s frontal airbag ON
and OFF indicator

All related wiring

SRS airbag system servicing
If the warning light exhibits any of
the following conditions, there may
be a malfunction in the seatbelt pre-
tensioners and/or SRS airbag sys-
tem. Immediately take your vehicle
to your nearest Saab dealer to have
the system checked. Unless
checked and properly repaired, the
seatbelt pretensioners and/or SRS
airbag will not operate properly in
the event of a collision, which may
increase the risk of injury.

Flashing or flickering of the warn-
ing light

No illumination of the warning
light when the ignition switch is
first turned to the “ON” position

Continuous illumination of the
warning light

Illumination of the warning light
while driving

When discarding an airbag mod-
ule or scrapping the entire vehicle
damaged by a collision, consult
your Saab dealer.

The SRS airbag has no user-ser-
viceable parts. Do not use electri-
cal test equipment on any circuit
related to the SRS airbag system.
For required servicing of the SRS
airbag, see your nearest Saab
dealer. Tampering with or discon-
necting the system’s wiring could
result in accidental inflation of the
SRS airbag or could make the sys-
tem inoperative, which may result
in serious injury. The wiring har-
nesses of the SRS airbag system
are covered with yellow insulation
and system connectors are yellow
for easy identification.
A1910BE-A-GSAAB.book Page 54 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

13
Instruments and controls
Ignition switch .................................................... 3-3
LOCK ....................................................................... 3-3
ACC .......................................................................... 3-4
ON ............................................................................ 3-4
START ...................................................................... 3-4
Key reminder chime ............................................... 3-5
Ignition switch light 3 ............................................ 3-5
Key interlock release (AT vehicles only) .............. 3-5
Hazard warning flasher ...................................... 3-6
Meters and gauges ............................................. 3-6
Speedometer ........................................................... 3-6
Odometer/Trip meter .............................................. 3-6
Tachometer ............................................................. 3-7
Fuel gauge ............................................................... 3-7
Temperature gauge ................................................ 3-8
Outside temperature indicator .............................. 3-9
Warning and indicator lights ............................. 3-8
Seatbelt warning light and chime .......................... 3-9
SRS airbag system warning light .......................... 3-10
Front passenger’s frontal airbag ON and OFF
indicators .............................................................. 3-10
CHECK ENGINE warning light/Malfunction
indicator lamp ....................................................... 3-11
Charge warning light .............................................. 3-11
Oil pressure warning light ..................................... 3-11
AT OIL TEMPerature warning light
(AT vehicles) ......................................................... 3-12
ABS warning light ................................................... 3-12
Brake system warning light ................................... 3-13Door open warning light ........................................ 3-13
All-Wheel Drive warning light (AWD AT
vehicles) ................................................................ 3-14
Selector lever position indicator (AT
vehicles) ................................................................ 3-14
Turn signal indicator lights .................................... 3-14
High beam indicator light ....................................... 3-14
Cruise control indicator light ................................. 3-14
Cruise control set indicator light .......................... 3-15
Clock .................................................................... 3-15
Light control switch ........................................... 3-15
Headlights ............................................................... 3-16
High/low beam change (dimmer) .......................... 3-16
Headlight flasher ..................................................... 3-16
Daytime running light system ............................... 3-17
Turn signal lever ................................................. 3-17
Illumination brightness control ......................... 3-18
Headlight beam leveler (Cars with HID
headlights only) ............................................... 3-18
Parking light switch ........................................... 3-19
Front fog light button
3 ..................................... 3-19
Wiper and washer ............................................... 3-20
Windshield wiper and washer switches ............... 3-21
Rear window wiper and washer switch ................ 3-22
Rear window defogger button ........................... 3-23
Windshield wiper deicer
3 ................................. 3-24
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

3-6
Instruments and controls
Hazard warning flasherThe hazard warning flasher is used to
warn other drivers when you have to park
your vehicle under emergency conditions.
The hazard warning flasher works with the
ignition switch in any position.
To turn on the hazard warning flasher,
push the hazard warning button on the in-
strument panel. To turn off the flasher,
push the button again.NOTEWhen the hazard warning flasher is on,
the turn signals do not work.
Meters and gaugesNOTELiquid-crystal displays are used in
some of the meters and gauges in the
combination meter. You will find their
indications hard to see if you wear po-
larized glasses.
SpeedometerThe speedometer shows the vehicle
speed.
Odometer/Trip meter1) Trip meter
2) OdometerThis meter displays the odometer and twotrip meters when the ignition switch is in
the “LOCK”, “ACC” or “ON” position.

Odometer
The odometer shows the total distance
that the vehicle has been driven.

Double trip meter
The trip meter shows the distance that the
vehicle has been driven since you last set
it to zero.
To change the mode indication, briefly
push the knob.
Each press of the knob changes the func-
tion alternately.
To set the trip meter to zero, select the A
300117
1
2
300614
300660
A trip meter B trip meter
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Instruments and controls
3-7
3
– CONTINUED –
trip or B trip meter by pushing the knob
and keep the knob pushed for more than
2 seconds.NOTEIf the connection between the instru-
ment cluster and battery is broken for
any reason such as vehicle mainte-
nance or fuse replacement, the data re-
corded on the trip meter will be lost.
TachometerThe tachometer shows the engine speed
in thousands of revolutions per minute.

Fuel gauge1) Low fuel warning lightThe fuel gauge shows the approximate
amount of fuel remaining in the tank.
The gauge does not return to “E” eventhough the ignition switch is in the “ACC”
or “LOCK” position.
The gauge may move slightly during brak-
ing, turning or acceleration due to fuel lev-
el movement in the tank.

Low fuel warning light
The low fuel warning light comes on when
the tank is nearly empty [approximately
2.3 US gal (9.0 liters)]. It only operates
when the ignition switch is in the “ON” po-
sition.
NOTEThis light does not go out unless the
tank is replenished up to an internal
fuel quantity of approximately 4.0 US
gal (15 liters).
To ensure safety, do not attempt to
change the function of the indicator
during driving, as an accident could
result.
Do not operate the engine with the
pointer of the tachometer in the red
zone. In this range, fuel injection will
be cut by the engine control module
to protect the engine from overrev-
ving. The engine will resume run-
ning normally after the engine
speed is reduced below the red
zone.
1
300628
(Turbo model only)
Promptly put fuel in the tank when-
ever the low fuel warning light
comes on. Engine misfires as a re-
sult of an empty tank could cause
damage to the engine.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Instruments and controls
3-9
3
– CONTINUED –
Warning and indicator lightsSeveral of the warning and indicator lights
come on momentarily and then go out
when the ignition switch is initially turned
to the “ON” position. This permits check-
ing the operation of the bulbs.
Apply the parking brake and turn the igni-
tion switch to the “ON” position. The fol-
lowing lights come on:

Seatbelt warning light

SRS airbag system warning light

Front passenger’s frontal airbag ON in-
dicator light

Front passenger’s frontal airbag OFF
indicator light

CHECK ENGINE warning light/Mal-
function indicator lamp

Charge warning light

Oil pressure warning light

AT OIL temperature warning light (AT
vehicles)

ABS warning light

Brake system warning light

All-Wheel Drive warning light (AWD AT
vehicles)

Cruise control indicator light 3

Cruise control set indicator light 3
If any lights fail to come on, it indicates a
burned-out bulb or a malfunction of the
corresponding system.Consult your authorized Saab dealer for
repair.

Seatbelt warning light
and chimeYour vehicle is equipped with a seatbelt
warning device at the driver’s seat, as re-
quired by current safety standards. There
is a seatbelt warning light in the combina-
tion meter.
If the driver has not yet fastened the seat-
belt when the ignition switch is turned to
the “ON” position, the seatbelt warning
light will flash for 6 seconds, to warn that
the seatbelt is unfastened. If the driver’s
seatbelt is not fastened, a chime will also
sound simultaneously.
If the driver’s seatbelt is still not fastened
6 seconds later, the warning light will re-
main lit for 15 seconds. If the driver’s seat-
belt is still not fastened even 15 seconds
later (21 seconds after turning ON the ig-
nition switch), the warning lights will alter-
nate between flashing and steady illumi-
nation at 15-second intervals, and the
chime will sound while the warning light is
flashing.
Alternate flashing and steady illumination
of the warning lights and sounding of the
chime will continue until the driver fastens
the seatbelt.
NOTE
If the driver unfastens the seatbelt af-
ter fastening, the seatbelt warning de-
vice operates as follows according to
the vehicle speed.

At speeds lower than approximate-
ly 9 mph (15 km/h)
The warning light will alternate be-
tween flashing and steady illumina-
tion at 15-second intervals. The
chime will not sound.

At speeds higher than approxi-
mately 9 mph (15 km/h)
The warning light will alternate be-
tween flashing and steady illumina-
tion at 15-second intervals and the
chime will sound while the warning
light is flashing.

It is possible to cancel the warning
operation that follows the 6-second
warning after turning ON the ignition
switch by unfastening and refastening
the driver’s seatbelt. When the ignition
switch is turned ON next time, howev-
er, the complete sequence of warning
operation resumes. For further details
about canceling the warning operation,
please contact your Saab dealer.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

3-10
Instruments and controls

SRS airbag system
warning lightWhen the ignition switch is turned to the
“ON” position, the SRS airbag system
warning light will come on for approxi-
mately six seconds and go out. This
shows the SRS airbag and SRS side air-
bag 3 and seatbelt pretensioners are in
normal operation.

Front passenger’s frontal air-
bag ON and OFF indicators
:Front passenger’s frontal airbag
ON indicator
:Front passenger’s frontal airbag
OFF indicator
The front passenger’s frontal airbag ON
and OFF indicators show you the status of
the front passenger’s SRS frontal airbag.
The indicators are located next to the
clock in the central portion of the instru-
ment panel.When the ignition switch is turned to the
“ON” position, both the ON and OFF indi-
cators illuminate for 6 seconds during
which time the system is checked. Follow-
ing the system check, both indicators ex-
tinguish for 2 seconds. After this, one of
the indicators illuminates depending on
the status of the front passenger’s SRS
frontal airbag reached by the Saab ad-
vanced frontal airbag system monitoring.
If the front passenger’s SRS frontal airbag
is activated, the passenger’s frontal airbag
ON indicator will illuminate while the OFF
indicator will remain extinguished.
If the front passenger’s SRS frontal airbag
is deactivated, the passenger’s frontal air-
bag ON indicator will remain extinguished
while the OFF indicator will illuminate.
With the ignition switch turned to the “ON”
position, if both the ON and OFF indica-
tors remain lit or extinguished simulta-
neously even after the system check peri-
od, the system is faulty. Contact your
Saab dealer immediately for an inspec-
tion. If the warning light exhibits any of
the following conditions, there may
be a malfunction in the seatbelt pre-
tensioners and/or SRS airbag sys-
tem. Immediately take your vehicle
to your nearest Saab dealer to have
the system checked. Unless
checked and properly repaired, the
seatbelt pretensioners and/or SRS
airbag will not operate properly in
the event of a collision, which may
increase the risk of injury.

Flashing or flickering of the warn-
ing light

No illumination of the warning
light when the ignition switch is
first turned to the “ON” position
Continuous illumination of the
warning light

Illumination of the warning light
while driving
PASS AIR BAGOFFOFF
ONON
100704
ON orOFF or
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Instruments and controls
3-11
3
– CONTINUED –

CHECK ENGINE warn-
ing light/Malfunction in-
dicator lampIf this light comes on steadily or blinks
while the engine is running, it may indicate
that there is a problem or potential prob-
lem somewhere in the emission control
system.

If the light comes on steadily:
If the light comes on steadily while driving
or does not go out after the engine starts,
an emission control system malfunction
has been detected.
You should have your vehicle checked by
an authorized Saab dealer immediately.NOTEThis light also comes on when the fuelfiller cap is not tightened until it clicks.
If you have recently refueled your vehicle,
the cause of the CHECK ENGINE warning
light/malfunction indicator lamp coming on
could be a loose or missing fuel filler cap.
Remove the cap and retighten it until it
clicks. Make sure nothing is interfering
with the sealing of the cap. Tightening the
cap will not make the CHECK ENGINE
warning light turn off immediately. It may
take several driving trips. If the light does
not go out, take your vehicle to your au-
thorized Saab dealer immediately.

If the light is blinking:
If the light is blinking while driving, an en-
gine misfire condition has been detected
which may damage the emission control
system.
To prevent serious damage to the emis-
sion control system, you should do the fol-
lowing.

Reduce vehicle speed.

Avoid hard acceleration.

Avoid steep uphill grades.

Reduce the amount of cargo, if possi-
ble.

Stop towing a trailer as soon as pos-
sible.
The CHECK ENGINE warning light may
stop blinking and come on steadily afterseveral driving trips. You should have
your vehicle checked by an authorized
Saab dealer immediately.

Charge warning light If this light comes on when the engine is
running, it may indicate that the charging
system is not working properly.
If the light comes on while driving or does
not go out after the engine starts, stop the
engine at the first safe opportunity and
check the alternator belt. If the belt is
loose, broken or if the belt is in good con-
dition but the light remains on, contact
your nearest Saab dealer immediately.
Oil pressure warning
lightIf this light comes on when the engine is
running, it may indicate that the engine oil
pressure is low and the lubricating system
is not working properly.
If the light comes on while driving or does
not go out after the engine starts, stop the
engine at the first safe opportunity and
check the engine oil level. If the oil level is
low, add oil immediately. If the engine oil
is at the proper level but the light remains
on, contact your nearest Saab dealer im-
mediately. If the CHECK ENGINE light comes
on while you are driving, have your
vehicle checked/repaired by your
Saab dealer as soon as possible.
Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could cause serious damage, which
may not be covered by your vehi-
cle’s warranty.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com