2006 RENAULT SCENIC wheel

TYRE PRESSURE MONITOR
Fault finding - Fault Finding Chart
35B
ALP 3"Adjust tyre pressure" message lights up (two wheels fill in on
the display)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Is there a pressure
imbalance between the
left-hand and right-hand
tyre on the same axle?NO
YES
Adjust the tyre pressure to the
manufacturer's recommended
levels.
NO
Is the fault still present?End of fault finding
YES
Read the recommended
pressures in the UCH (PR009
to PR012).
Do the values of these
parameters match the
manufacturer's
recommended pressures?NO
YES
Contact the Techline.
Check the positions of the
coloured rings against the
label on the driver's side.
Have the front and rear
tyres been swapped?YES
NO
Write the recommended
pressures with command
VP005 Enter
recommended pressures.
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
AFTER REPAIRCarry out a complete check with the diagnostic tool.
35B-32
Program the four valve
codes and refit the
coloured rings in the
position indicated on the
label on the driver's side.
SSPP_V48_ALP03 /SSPP_V4C_ALP03/SSPP_V4D_ALP03/SSPP_V4F_ALP03/SSPP_V50_ALP03
Edition 4

TYRE PRESSURE MONITOR
Fault finding - Fault Finding Chart
35B
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
ALP 4"Tyre sensor inoperative" message lights up (wheel warning light
disappears)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Has one of the wheels been replaced with
the spare?YES
NO
Program the four valve codes with command
SC002 Program the four valve codes.
Did the programming procedure go
properly?
NO YES
End of fault finding
Replace the faulty valve.
Do the necessary work
on the wheel with a tyre
pressure monitor valve,
then refit it on the vehicle
AFTER REPAIRCarry out a complete check with the diagnostic tool.
35B-33
SSPP_V48_ALP04 /SSPP_V4C_ALP04/SSPP_V4D_ALP04/SSPP_V4F_ALP04/SSPP_V50_ALP04
Edition 4

TYRE PRESSURE MONITOR
Fault finding - Fault Finding Chart
35B
ALP 5"Tyre sensor inoperative" message lights up (four wheel symbol
warning lights disappear)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Are the wheels fitted with tyre pressure
monitor valves?NO
YES
Check the configuration of the Tyre Pressure
Monitor in the UCH (LC017 Tyre Pressure
Monitor Function).
Is the UCH set to "With" for the Tyre Pressure
Monitor function?NO
YES
NO
Have the valve codes been programmed?
YES
Make sure the ABS is transmitting the vehicle
speed (PR008 Vehicle speed).
YES
Is there an ABS fault?
UCH fault, contact the Techline.
Program the four valve codes with command
SC002 Program the four valve codes.
Is the vehicle equipped with the Tyre
Pressure Monitor option?
YES NO
Install the Tyre Pressure
Monitor valves.
Deconfigure the Tyre Pressure Monitor in the
instrument panel.
Configure the UCH with the Tyre Pressure
Monitor function by using command CF023 Tyre
Pressure Monitor function under SC008 UCH
type.
Run full fault finding on the ABS.
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
AFTER REPAIRCarry out a complete check with the diagnostic tool.
35B-34
SSPP_V48_ALP05 /SSPP_V4C_ALP05/SSPP_V4D_ALP05/SSPP_V4F_ALP05/SSPP_V50_ALP05
Edition 4

TYRE PRESSURE MONITOR
Fault finding - Fault Finding Chart
35B
ALP 6"Tyre sensor inoperative" message lights up (disappearance of
one or both rear wheels, intermittent event)
NOTESCheck that all the faulty tyres are fitted with tyre pressure monitor valves.
Use status ET045 RF signal received to check
that the receiving aerial works correctly by
requesting central door locking with the card 4
to 5 metres to the rear of the vehicle, right-hand
side.
If central door locking does not work, check
receiving aerial presence, positioning and
connection on the UCH.
NO
Is the aerial correctly positioned and
connected?
YES
If the fault is still present, the UCH is faulty, and
you should contact the Techline.
Replace and reconnect the aerial on the UCH.
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
AFTER REPAIRCarry out a complete check with the diagnostic tool.
35B-35
SSPP_V48_ALP06 /SSPP_V4C_ALP06/SSPP_V4D_ALP06/SSPP_V4F_ALP06/SSPP_V50_ALP06
Edition 4

TYRE PRESSURE MONITOR
Fault finding - Fault Finding Chart
35B
ALP 7"Puncture: change tyre" message lights up (the wheel fills in on
the display)
NOTESNone.
Is the tyre punctured?
NO
Check the pressure in all four tyres with a
pressure gauge (fault: severely under-inflated).
NO
Is the pressure correct?
YES
Read the recommended pressures in the UCH
(PR009 to PR012)
Do the values of these parameters match the
manufacturer's recommended pressures?
NO YES
Write the recommended
pressures with command VP005
Enter recommended pressures.
Contact the Techline.
YES
UCH
Program no.: 350 and higher
Vdiag No: 48-4C-4D-4F-50
Repair the tyre
Make sure the valve seal is not damaged.
Make sure the sealing nut on the sensor is one for
valves installed on the Mégane II or Scénic II,
and not one for a Laguna II, Vel Satis or
Espace IV.
After all these checks, if the message still appears
on the instrument panel, contact your Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
35B-36
SSPP_V48_ALP07 /SSPP_V4C_ALP07/SSPP_V4D_ALP07/SSPP_V4F_ALP07/SSPP_V50_ALP07
Edition 4