2006 RENAULT SCENIC lock

POWER ASSISTED STEERING
Fault finding - Fault Finding Chart
36B
36B - 51V6 MR-366-X84-36B000$924_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
ALP6 Too little assistance
NOTESAt full lock, steering assistance is reduced after 5 seconds.
Check the pressures and condition of the tyres, the condition of the joints and the front axle geometry.
Check the vehicle's battery voltage.
Repair if necessary.
Make sure that computer calibration ET026 is in order (consult the help for ET026 on the Clip tool). Calibrate the
computer using command SC001 if necessary.
Check the conformity of PR014 Assistance level available.
Do not use the electric power steering for about fifteen minutes.
Make sure that no components located in the vicinity of the electric power steering are promoting a temperature
rise in the system.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
DAETRW_V04_ALP06/DAETRW_V08_ALP06/DAETRW_V06_ALP06/DAETRW_V0C_ALP06/
DAETRW_V12_ALP06

POWER ASSISTED STEERING
Fault finding - Fault Finding Chart
36B
36B - 55V6 MR-366-X84-36B000$924_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
ALP10 The vehicle pulls to the right or to the left
NOTESNone
Check that the casing under the steering wheel does not rub on the steering column or steering wheel.
Check the tyre pressures and the condition of the joints and the steering geometry.
Repair if necessary.
Check status ET020 Steering wheel angle sensor programming, which must be STATUS 4.
Position the vehicle wheels in the straight line driving position (steering centre point).
Consult parameter PR121 Steering wheel angle which must be between - 10d˚ < X < 10d˚.
Turn the steering wheel to full right lock then to full left lock, and check that the parameter varies within the
tolerances given in the Conformity check.
Check the position of the steering wheel on the splines of the steering column.
If parameter PR121 Steering wheel angle and status ET020 Steering wheel angle sensor programming listed
above are not correct:
Place the vehicle on a front axle adjusting bench.
Position the vehicle wheels in the straight line driving position (steering centre point).
Program the steering wheel angle using command VP004 Steering wheel angle sensor programming (see
Configuration and programming).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
DAETRW_V04_ALP10/DAETRW_V08_ALP03/DAETRW_V06_ALP10/DAETRW_V0C_ALP10/
DAETRW_V12_ALP10

POWER ASSISTED STEERING
Fault finding - Fault Finding Chart
36B
36B - 56V6 MR-366-X84-36B000$924_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
ALP11The engine does not start and the "steering not unlocked" or
"steering not locked" message is displayed after the ignition is
switched off
NOTESSpecial notes:
An electric power-assisted steering failure is not the reason these messages are
displayed.
Check the UCH (see 87B, Passenger compartment connection unit)
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
DAETRW_V04_ALP11 /DAETRW_V08_ALP11 /DAETRW_V06_ALP11/DAETRW_V0C_ALP11/
DAETRW_V12_ALP11