2006 RENAULT SCENIC engine

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 25V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12POWER ASSISTED STEERING
Fault finding - Conformity check
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Steering wheel
angleET020:Steering wheel
angle sensor
programmingStatus 4: calibrated
and initialisedIn the event of a fault, consult
the interpretation of status
ET020.
2EngineET023:Engine
operationSTOPPED: engine
stopped.
STALLED: engine
stopped without using
the ignition keyIn the event of a fault, test the
multiplex network.
3Computer
supplyPR108:Computer feed
voltage9 V < X < 16 VIf the computer supply
voltage is not sufficient,
dialogue cannot be
established.
If PR108 is not correct, run
fault finding on the charge
circuit.
4Vehicle speedPR003:Vehicle speed0 mph (0 km/h) when
stationaryIn the event of a fault, test the
multiplex network.
5Electric motorPR012:Current
absorbed by the
motor0 A < X < 1 AWithout any action on the
steering wheel.
6Thermal
protectionPR119:Motor thermal
protection
indicatorInterior temperature
± 5 ˚CIf PR119 > 60˚C, thermal
protection is activated.
The assistance level PR140
= 15 %. To deactivate
thermal protection, do not
operate the EPAS for
15 minutes. PR014:Level of
assistance
available99 % or 0 %
depending on Vdiag
15 % if thermal
protection activated.
DAETRW_V04_CCONF/DAETRW_V08_CCONF/DAETRW_V06_CCONF/DAETRW_V0C_CCONF
MR-366-X84-36B000$528_eng.mif

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 26V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1EngineET023:Engine
operationSTOPPED or
STALLEDIn the event of a fault, test the
multiplex network.
2Computer
supplyPR108:Computer feed
voltage9 V < X < 16 VIf the computer supply
voltage is not sufficient,
dialogue cannot be
established.
If PR108 is not correct, run
fault finding on the charge
circuit.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 27V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: ASSISTANCE
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Steering
wheel
angleET020:Steering wheel
angle sensor
programmingStatus 4: calibrated
and initialisedIn the event of a fault, refer to
the interpretation of status
ET020.
PR121:Steering wheel
angle0˚ with the wheels set
straight ahead
+ or - 580˚ at full lockIn the event of a fault, consult
the interpretation of PR121.
2Vehicle
speedPR003:Vehicle speed0 mph (km/h) when
stationaryIn the event of a fault, test the
multiplex network.
3TorquePR001:Torque applied to
the steering wheel0 Nm ± 0.2 Nm
with no action on the
steering wheelIn the event of a fault, consult
the interpretation of PR001.
PR006:Steering motor
torque setpoint0 Nm ± 0.2 NmIn the event of a fault, consult
the interpretation of PR006.
4Motor
powerPR012:Current absorbed
by the motor0 A < X < 1 AIn the event of a fault, consult
the interpretation of PR012.
PR013:Setpoint for
current absorbed
by the motor0 A < X < 1 AIn the event of a fault, consult
the interpretation of PR013.
5Thermal
protectionPR119:Motor thermal
protection
indicatorInterior temperature
± 5˚CIf PR119 > 60 ˚C, thermal
protection is activated.
The level of assistance
PR014 = 15 %.
To deactivate the thermal
protection, do not operate the
EPAS for 15 minutes. PR014:Level of
assistance
available0 % or 99 %
depending on Vdiag
15 % if thermal
protection activated.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 28V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: ASSISTANCE (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Execution conditions: ENGINE STOPPED, IGNITION ON.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
6Computer
calibrationET026:Computer
calibrationConfiguration 1 to 5
according to
equipment and vehicle
type.Redefine the vehicle
specifications using
command SC001 Computer
calibration.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 29V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Test condition: ENGINE AT IDLE SPEED.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Steering wheel
angleET020:Steering wheel
angle sensor
programmingStatus 4: calibrated
and initialisedIn the event of a fault, consult
the interpretation of status
ET020.
2EngineET023:Engine
operationRUNNINGIn the event of a fault, test the
multiplex network.
3Computer
supplyPR108:Computer feed
voltage12 V < X < 16 VIf the computer supply
voltage is not sufficient,
dialogue cannot be
established.
If PR108 is not correct, run
fault finding on the charge
circuit.
4Vehicle speedPR003:Vehicle speed0 mph (0 km/h) when
stationaryIn the event of a fault, test the
multiplex network.
5Electric motorPR012:Current
absorbed by the
motor- 90 < X < 90A ± 5ANone
6Thermal
protectionPR119:Motor thermal
protection
indicatorInterior temperature
± 5 ˚CIf PR119 > 60 ˚C, thermal
protection is activated.
The assistance level PR140
= 15 %.
To deactivate thermal
protection, switch off the
engine and do not operate
the EPAS for 15 minutes. PR014:Level of
assistance
available100 % idling
15 % if thermal
protection activated.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 30V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: POWER
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Test condition: ENGINE AT IDLE SPEED.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1EngineET023:Engine
operationRUNNINGIn the event of a fault, test the
multiplex network.
2Computer
supplyPR108:Computer feed
voltage12 V < X < 16 VIf the computer supply
voltage is not sufficient,
dialogue cannot be
established.
If PR108 is not correct, run
fault finding on the charge
circuit.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 31V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: ASSISTANCE
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Test condition: ENGINE AT IDLE SPEED.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Steering
wheel
angleET020:Steering wheel
angle sensor
programmingStatus 4: calibrated
and initialisedIn the event of a fault, refer to
the interpretation of status
ET020.
PR121:Steering wheel
angle0˚ with the wheels set
straight ahead
+ or - 570˚ ± 20˚ at full
lockIn the event of a fault, consult
the interpretation of PR121.
2Vehicle
speedPR003:Vehicle speed0 mph (km/h) when
stationaryIn the event of a fault, test the
multiplex network.
3TorquePR001:Torque applied to
the steering wheel- 11 Nm < X
< + 11 Nm
with action on the
steering wheelIn the event of a fault, consult
the interpretation of PR001.
PR006:Steering motor
torque setpoint0 Nm ± 0.2 NmIn the event of a fault, consult
the interpretation of PR006.
4Motor
powerPR012:Current absorbed
by the motor- 90 < X < 90A ± 5AIn the event of a fault, consult
the interpretation of PR012.
PR013:Setpoint for
current absorbed
by the motor- 90 < X < 90A ± 5ANone
5Thermal
protectionPR119:Motor thermal
protection
indicatorInterior temperature
± 5 ˚CIf PR119 > 60 ˚C, thermal
protection is activated.
The assistance level PR140
= 15 %.
To deactivate thermal
protection, switch off the
engine and do not operate the
EPAS for 15 minutes. PR014:Level of
assistance
available100 % idle speed
15 % if thermal
protection activated.

POWER ASSISTED STEERING
Fault finding - Conformity check
36B
36B - 32V6 MR-366-X84-36B000$528_eng.mif
PAS
Vdiag No.: 04, 06, 08, 0C
and 12
SUB-FUNCTION: ASSISTANCE (CONTINUED)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as examples.
Test condition: ENGINE AT IDLE SPEED.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
6Computer
calibrationET026:Computer
calibrationConfiguration 1 to 5
according to
equipment and vehicle
type.Redefine the vehicle
specifications using
command SC001 Computer
calibration.