2006 RENAULT SCENIC diagram

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-43
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET037
SATELLITE WHEEL
NOTESThere must be no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition and connection of the connector of component 325 (Scénic: 1519) and the black 24-track
connector of component 261 (commercial vehicle: 662).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_ET037

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-47
NAV 4R
Program no.: 0000
Vdiag No.: 24
Fault finding - Interpretation of parameters
PR001
BATTERY VOLTAGE
NOTESThere must be no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the permanent + feed fuse of component 261 (Trafic: 662).
Check the condition of the connectors of components 710 (Laguna), 260 (Mégane II and Scénic) or
1016 (commercial vehicle) according to the location of the fuse.
If the voltage is at minimum:
Check the battery and the charge circuit (see Technical Note 6014A Checking the charge circuit).
If the voltage is at maximum:
Check that the charging voltage is correct with and without electrical consumers switched on.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR001

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-49
NAV 4R
Program no.: 0000
Vdiag No.: 24
PR002
VEHICLE SPEED
NOTESThere must be no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Run fault finding on the ABS system (see 38C, Anti-lock braking system).
If there is no ABS system fault indicated, check connection 47F between components 1094 and 261 (Trafic: 662).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR002

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-50
NAV 4R
Program no.: 0000
Vdiag No.: 24
PR006
EXTERNAL TEMPERATURE
NOTESOnly apply the checks if the parameter is inconsistent.
There must be no present or stored faults.
Special notes:
On the Laguna, Trafic, Master and Master propulsion, the exterior temperature
information is supplied by the exterior temperature sensor.
On Mégane and Scénic, this information comes from the UCH.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Only for Laguna, Trafic, Master and Master propulsion
Check the condition and connection of the connector of component 240 (component 239 for right-hand drive
vehicles) and the black 24-track connector of component 261 (Trafic: 662).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on
the following connections:
Left-hand drive:
●47C connection code,
●47D connection code,
between components 261 (Trafic: 662) and 240.
Right-hand drive:
●47C connection code,
●connection code 47D,
between components 261 (Trafic: 662) and 239.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR006

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-52
NAV 4R
Program no.: 0000
Vdiag No.: 24
PR008
NUMBER OF SATELLITES RECEIVED
NOTESThere must be no present or stored faults.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition and connection of the GPS coaxial connector of the following components (bent pins, bad
contacts, etc.):
Commercial vehicle: 662 and 886.
Mégane cabriolet: 261, 1551 and 886.
Mégane and Scénic: 886 and 261.
Laguna: 261 and 1551.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the GPS coaxial cable at the rear of component 261 (Trafic: 662) and measure the resistance between
the core and the shielding.
If the resistance is less than 30 ΩΩ Ω Ω
, disconnect the GPS coaxial cable from the cut-off plate at the rear and check
the insulation, continuity and absence of interference resistance on the GPS coaxial cable at the rear of
component 261 (Trafic: 662).
If the connections are not correct, replace the coaxial cable.
If the connections are correct, replace the GPS aerial.
Mégane II ph2
(see MR 364 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Laguna II ph2
(see MR 395 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Scénic II ph2
(see MR 370 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Trafic II ph1 and ph2
(see MR 408 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Master ph2 and ph3
(see MR 377 mechanical, 83C On-board telematics system, Aerial: Removal - Refitting)
Master propulsion ph2
(see Technical Note 3818A, 83C On-board telematics system, Navigation aerial: Removal - Refitting).
If the resistance is greater than 30 ΩΩ Ω Ω
, check the feed voltage of component 1551 (4.5 V ±± ± ±
0.5 V) at the output of
component 1551 or 886.
If the voltage is not correct, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR008

MULTIMEDIA
Fault finding - Interpretation of parameters86C
86C-54
NAV 4R
Program no.: 0000
Vdiag No.: 24
PR009
ANGULAR POSITION
NOTESThere must be no present or stored faults.
Engine stopped, ignition on.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Remove component 261 (Trafic: 662) without disconnecting the connectors.
Shake the radio/navigation computer vigorously; parameter PR009 Angular position should be above or equal
to 1 d/s.
Each time the 4R radio/navigation computer is at rest, PR009 Angular position should be very close to 0 d/s.
If the parameter does not change, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_PR009

MULTIMEDIA
Fault finding - Dealing with commands
86C
86C-58
NAV 4R
Program no.: 0000
Vdiag No.: 24
AC004
SPEAKER TEST
NOTESThere must be no present or stored faults.
Special note:
A different bleep is emitted from each speaker.
Check that the "balance/fader" settings used are the default ones.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition and connection of the white 8-track connector of component 261 (Trafic: 662).
Also check the condition and connection of the faulty speaker connector.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-63
NAV 4R
Program no.: 0000
Vdiag No.: 24
Diagnostic - Fault finding chart
ALP 1 No dialogue possible between the computer and the CLIP tool
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Note:
For Laguna, the system can only be switched on with the ignition on. The on/off
button does not operate with the ignition off.
Try the diagnostic tool on another vehicle.
Yes Is dialogue possible with a computer? No
On the faulty vehicle.
Check the battery voltage (see PR001 Battery
voltage).
Check the condition and connection of the battery
connections.
Check the condition of the fuses.
Check:
–the connection between the diagnostic tool and the
diagnostic probe (lead in good condition):
–the connection between the diagnostic lead and the
diagnostic socket (lead in good condition).
AFTER REPAIRCarry out a complete check with the diagnostic tool.
NAV4R_V24_ALP1