2006 RENAULT SCENIC instrument panel

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-37
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET003
+ 12 V SIDE LIGHTS FEED
NOTESCheck that the instrument panel backlighting comes on when the lights are switched
on.
Use the Wiring Diagram Technical Note for the vehicle concerned.
Check the condition of the + side light feed fuse of component 261 (Trafic: 662).
Check the condition and connection of the connectors of components 261 (Trafic: 662) and 260, 1016 or 1337
according to the location of the fuse.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using the universal bornier, check the insulation, continuity and the absence of interference resistance on
the following connection:
Trafic:
●connection code LPG,
between components 662 and 1016.
Master:
●connection code LPG,
between components 261 and 1016.
Mégane and Scénic:
●connection code LPG,
between components 1337 and 261.
Laguna:
●connection code LPG,
between components 260 and 261.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_ET003

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C-38
NAV 4R
Program no.: 0000
Vdiag No.: 24
ET004
RADIO ON SIGNAL
NOTESThere must be no present or stored faults.
Switch on the ignition, status ET004 should be permanently PRESENT.
Apply this fault finding procedure only if the vehicle is equipped with a display fold-out
unit and an instrument panel dot matrix display (Mégane II ph2).
Use the Wiring Diagrams Technical Note for Mégane II phase 2.
Check the condition and connection of the yellow 6-track connector of component 261 and the connector of
component 1303.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on connection 34GG between
components 261 and 1303.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the connector of component 247.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on connection 34GD between
components 247 and 1303.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
NAV4R_V24_ET004

MULTIMEDIA
Diagnostic - Fault finding chart86C
86C-66
NAV 4R
Program no.: 0000
Vdiag No.: 24
ALP 2
CONTINUED
Check that the radio display appears on the
instrument panel dot matrix display (only on
Mégane).
No Yes
Check for + 12 V on connections 46M and 46N
and earth on connections 46BG, 46BH and
46BK of the connector of component 1127.
Are these tests correct?
Yes
Cut the + accessories feed (for at least 1 minute)
then re-activate it.
Is the fault still present?If the connection is faulty and there is a
repair procedure (see Technical
Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair
the wiring, otherwise replace it.
No
NoEnd of fault finding.
In the event of an intermittent
fault, contact the Techline.
YesContact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.