2006 RENAULT SCENIC automatic transmission

MULTIPLEXING
Fault finding - Configuration
88B
88B-5
MULTIPLEX NETWORK GENERIC ARCHITECTURE
Number of multiplex network segments between computers:
* A vehicle can have either LPG or automatic transmission, but never both.
** The vehicle either has just ABS or ABS + ESP (electronic stability program). 120 Injection
118 ABS **
1094 ABS+ESP **
1337 Switching Protection Unit
119 Automatic transmission *
997 LPG / GNV *
1088 Steering lock
1232 Electric power-assisted steering
247 Instrument panel
645 UCH 419 Air conditioning
1125 Control and Communications Unit
469 Driving School Unit
756 Airbag
1217 Automatic parking brake
989 Discharge bulbs
1222 Parking assistance

MULTIPLEXING
Diagnostics - Dealing with faults
88B
88B-8
FAULTY COMPUTER
NOTES–Make sure the computers installed in the vehicle are the correct type and are
compatible with Mégane II.
–Check the power supply to the computers (earth, + battery, + accessories or + after
ignition).
Make sure that the computer wake-up mode is in full working order on the vehicle and properly assimilated
by the computers.
The wake-up mode is:
–timed power supply: UCH, instrument panel.
–+ accessories: Protection and Switching Unit, air conditioning control panel, radio, Control and
Communications Unit.
–+ After ignition: Injection, ABS, airbag, Electric Power Assisted Steering, Automatic transmission, LPG,
Steering lock, Roof control unit, Driving school unit, Automatic parking brake, Parking assistance.
–+ After ignition + dipped headlights: Xenon bulbs.
WARNING
Dialogue with the Xenon bulbs is only possible with + after ignition and the dipped headlights on.
–Switch to computer diagnostics mode.
Test of communication with computers.
⇒No communication from computers to diagnostic tool: see Fault Finding Chart 1
No communication with the computer or computers not communicating with the
diagnostic tool.
Check the connections to the computers and for no open circuit. Repair if necessary.
⇒Computers that only produce partial information when identified:
Check in the Workshop Repair Manual or Global Vehicle Base to see that the computer
really is compatible with Scénic II.
Make sure the CLIP diagnostic tool update is recent enough to handle Scénic II faults.
If after these tests no irregularity or open or short circuit has been detected, contact your Techline.
AFTER REPAIRCarry out a new multiplex network test with the diagnostic tool.
Clear the stored faults on all the computers connected to the network.
Deal with any other possible faults.

MULTIPLEXING
Diagnostics - Dealing with faults
88B
88B-10
MULTIPLEX NETWORK OUT OF ORDER
Help finding network short circuits
NOTESGet a copy of the multiplex network wiring diagram for the vehicle and the diagnostic
socket diagram.
In the event of a short-circuit to + battery, leave the battery connected.
The test procedure involves disconnecting the various network components in sequence to pinpoint the faulty
one.
Check the condition of the connectors.
Check the condition of the multiplex network wires (CAN H - CAN L).
Repair the damaged components.
Systematically repeat the multiplex network test after each operation to see if the fault has been resolved. If
the fault is still shown as present, continue disconnecting the connectors and computers one by one.
Input Output
Connector Can H Can L Connector Can H Can L
Protection and Switching Unit Siemens PEH blue 10 8 PEH blue 11/12 7/9
K4J injection S 3000 C 2AN A black A4 A3
K4M - F4R injection S 3000 C 2AN A black A4 A3 2AN B brown K4 K3
K9K injection LVCR 2AN A black A4 A3
F9Q injection EDC 16 C Black A4 A3
Automatic transmission DP0 Black 38 39
ABS - ESP Black 35 14
ABS Black 26 15
Electric power-assisted steering TRW Black 7 5 Black 6
4
Airbag Black 11 10
Climate control Black 7 1
Steering lock Black 3 6
UCH PE 2 black 6 16 10/8 20/18
Instrument panelGrey
30 29 Red 2 3
Driving school unitBlack
A3 B3
Central communications unit Green 6 7 Grey 3 4
Automatic parking brake Grey A3 A2
R 2 Grey 2 3
R 369White
12 13
OBD (On Board Diagnostic)Black
614
If the fault is not visible, contact your Techline.
AFTER REPAIRCarry out a new multiplex network test with the diagnostic tool.
Clear the stored faults on all the computers connected to the network.
Deal with any other possible faults.

MULTIPLEXING
Diagnostics - Repair assistance
88B
88B-14
Diagnostics - Repair assistance
CHANGES IN SCENIC II DIAGNOSTICS
●Assistance with computer or faulty segment detection:
If the multiplex network is completely frozen, this command can isolate multiplex network segments and thereby
rule out those that respond properly to the tool. This makes it easier to pinpoint the origin of the failure.
The algorithm for help with locating faults is intended for dealing with electrical faults present solely in CAN; it is
therefore essential that connectors and computers not attached to the bus are not taken into consideration.
●A test for multiplex network faults by using physical measurements:
When a multiplex network segment has a short circuit, the computers can no longer communicate with each other
nor with the diagnostic tool. At this point, the network test is out of order.
The CLIP tool can identify several types of faults by taking electrical measurements on the CAN H and CAN L
multiplex network. It can detect a CAN L / CAN H short circuit, a CAN L / + 12 V short circuit, a CAN H / + 12 V short
circuit, and a CAN H / earth short circuit.
Then, by disconnecting the connectors and computers in the order described under the "Help with detecting
segments - computers" heading, the actual or possible segment causing the multiplex network fault can be
identified.
●Disconnecting connectors and computers:
⇒ Help with locating network faults screen
In keeping with the diagnostic tool algorithm and based on the results obtained as it unfolds, the order for
disconnecting connectors and computers recommended by the diagnostic tool will probably be as follows:
Injection, ABS, Protection and Switching Unit, automatic transmission, LPG, steering lock, electric power-
assisted steering, instrument panel, UCH, heating and ventilation system, Control and Communications
Unit, R369 Union, Driving School Unit, airbag, R2 Union, automatic parking brake.
NOTE:
The tool sometimes requests that computers not present in the vehicle concerned be disconnected; in this case,
make sure that the computer in question is not installed, and confirm as though the component concerned had been
disconnected and reconnected and continue the test.
Network physical measurements screen
With the second screen, the operator can check the status of the multiplex network after each disconnection /
reconnection procedure involving the selected connector or computer. This enables the operator to check the status
of the multiplex network after disconnecting each component.