2006 PONTIAC SOLSTICE trunk

Filling a Portable Fuel Container
{CAUTION:
Never ll a portable fuel container while it is in
your vehicle. Static electricity discharge from
the container can ignite the gasoline vapor.
You can be badly burned and your vehicle
damaged if this occurs. To help avoid injury to
you and others:
Dispense gasoline only into approved
containers.
Do not ll a container while it is inside a
vehicle, in a vehicle’s trunk, pickup bed, or
on any surface other than the ground.
Bring the ll nozzle in contact with the
inside of the ll opening before operating
the nozzle. Contact should be maintained
until the lling is complete.
Do not smoke while pumping gasoline.
Checking Things Under
the Hood
{CAUTION:
An electric fan under the hood can start up
and injure you even when the engine is not
running. Keep hands, clothing and tools away
from any underhood electric fan.
{CAUTION:
Things that burn can get on hot engine parts
and start a re. These include liquids like fuel,
oil, coolant, brake uid, windshield washer and
other uids, and plastic or rubber. You or
others could be burned. Be careful not to drop
or spill things that will burn onto a hot engine.
5-10

Taillamps, Turn Signal, and
Stoplamps
To replace one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 2-9for
more information.
2. Remove the
two screws, which
hold the taillamp
assembly, from
inside the vehicle.
3. Remove the taillamp assembly.
4. Turn the bulb socket counterclockwise to remove.
5. Pull the bulb from the socket.
6. Install a new bulb.
7. Reverse the steps to reinstall the taillamp assembly.
Back-Up Lamps
The back-up lamps are
located in the rear bumper.
To replace a bulb, do the following:
1. Reach behind, up and under the rear bumper and
locate the bulb socket.
2. Turn it counterclockwise to remove from the
bulb assembly.
3. Pull the bulb from the bulb socket.
4. Push in a new bulb into the bulb socket.
5. Reinstall the bulb socket by lining up the tabs in the
lamp assembly and turn it clockwise to secure it.
5-42

The kit includes the following:
A. Air Compressor
B. Tire Sealant
Canister
C. Air Compressor
Accessory PlugD. On/Off Switch
E. Air Pressure Gage
F. Air Compressor
Inator Hose
G. Sealant
Filling Hose
If the at tire is due to a slow leak caused by a nail or
other similar road hazard, the tire inator kit may
be used to temporarily repair the damaged tire.After temporarily repairing a tire with the tire inator kit,
take your vehicle to an authorized GM dealer to
have the tire inspected and repaired.
Accessing the Tire Inator Kit
To access the tire inator kit, do the following:
1. Make sure the convertible top is in the up position
before accessing the tire inator kit.
2. Open the trunk. SeeTrunk on page 2-9for more
information.
3. Locate the tire inator kit on the driver’s side of the
vehicle, near the back corner of the trunk.
5-61

16. If the at tire was able
to inate to the
recommended ination
pressure, remove the
maximum speed label
from the sealant
canister and place in a
highly visible location
such as the inside of
the upper left corner of
the windshield or to the
face of the radio/clock.
The maximum speed label reminds you to drive
cautiously and not to exceed 55 mph (90 km/h) until
you have the damaged tire inspected and repaired.
{CAUTION:
Storing the tire inator kit or other equipment
in the passenger compartment of the vehicle
could cause injury. In a sudden stop or
collision, loose equipment could strike
someone. Store the tire inator kit in the
proper place.17. Return the equipment to the proper storage location
in the trunk of your vehicle. You may need to
loosen the retention strap to wrap it around the
inator kit and foam container. To do this, pull apart
the strap and loosen the strap at the quick release
buckle. Then snap the buckle together, pull the
strap tight, and secure the loose end of the strap by
mating the ends.
18. Immediately drive the vehicle 5 miles (8 km) to
distribute the sealant evenly in the tire. Stop at a
safe location and check the tire pressure, refer
to Steps 1 through 8 under “Using the Air
Compressor without Sealant” next in this section. If
the tire pressure has fallen more then 10 psi
(68 kPa), below the recommended ination
pressure, stop driving the vehicle. The tire is too
damaged for the sealant to work. SeeRoadside
Assistance Program on page 7-6.
If the tire pressure has not dropped more than
10 psi (68 kPa) from the recommended ination
pressure, you can inate the tire back up to
the recommended ination pressure.
19. Dispose of the sealant canister at a local GM dealer
or in accordance with your local state codes and
practices. After using the sealant canister, replace it
with a new canister from a GM dealer.
20. After temporarily repairing a tire with the emergency
at tire repair kit, take your vehicle to an authorized
GM dealer to have the tire inspected and repaired.
5-65

{CAUTION:
Idling the engine in a closed-in place or with
the climate control system off can cause
deadly carbon monoxide (CO). SeeEngine
Exhaust on page 2-28.
7. Start the vehicle. SeeStarting the Engine on
page 2-19for more information. The vehicle must be
running while using the air compressor.
{CAUTION:
Inating something too much can make it
explode, and you or others could be injured.
Be sure to read the inator instructions, and
inate the tire to its recommended pressure.
Do not exceed 36 psi (248 kPa).
8. Move the inator kit switch to the I (on) position.9. Inate the tire up to the recommended ination
pressure using the air pressure gage on the top
of the unit.
10. Turn off the air compressor by moving the switch to
the O (off) position.
{CAUTION:
Storing the tire inator kit or other equipment
in the passenger compartment of the vehicle
could cause injury. In a sudden stop or
collision, loose equipment could strike
someone. Store the tire inator kit in the
proper place.
11. Place the equipment in the original location in the
trunk of your vehicle.
5-67

Underhood Fuse Block
The underhood fuse block is located in the engine
compartment on the passenger’s side of the vehicle.
Lift the cover for access to the fuse block.
To remove fuses, use the fuse puller, or hold the end of
the fuse between your thumb and index nger and
pull straight out.
SeeEngine Compartment Overview on page 5-12for
more information on location.
Fuses Usage
1 Empty
2 Rear Window Defogger
Fuses Usage
3 Empty
4 Body Control Module 3
5 Crank
6 Body Control Module 2
7 Body Control Module
8 Cooling Fan 2
9 Empty
10 Trunk
11 Trunk
12 Empty
13 Fuel Pump
14 Rear Defogger Relay
15 Air Conditioning Clutch
16 Empty
17 Empty
18 Trunk Release
19 Fuel Pump
20 Empty
21 Mirrors
22 Air Conditioning
23 Empty
24 Cooling Fan 2 Relay
25 Fuse Puller
26 Powertrain Relay
5-80

Tires (cont.)
Tire Inator Kit............................................5-60
Tire Sidewall Labelling..................................5-46
Tire Terminology and Denitions....................5-47
Uniform Tire Quality Grading.........................5-55
Wheel Alignment and Tire Balance.................5-56
Wheel Replacement.....................................5-56
When It Is Time for New Tires......................5-52
Towing
Recreational Vehicle.....................................4-34
Towing a Trailer..........................................4-34
Your Vehicle...............................................4-34
Traction
Limited-Slip Rear Axle.................................... 4-9
Transmission
Fluid, Automatic...........................................5-19
Fluid, Manual..............................................5-19
Transmission Operation, Automatic....................2-20
Transmission Operation, Manual........................2-23
Trunk.............................................................. 2-9
Turn and Lane-Change Signals.......................... 3-8
Turn Signal/Multifunction Lever........................... 3-7U
Understanding Radio Reception........................3-70
Uniform Tire Quality Grading............................5-55
V
Vehicle
Control........................................................ 4-5
Damage Warnings........................................... iv
Loading......................................................4-29
Parking Your...............................................2-27
Service Soon Light......................................3-34
Symbols......................................................... iv
Vehicle Data Collection and Event Data
Recorders.................................................... 7-9
Vehicle Identication
Number (VIN).............................................5-77
Service Parts Identication Label...................5-77
Vehicle Personalization
DIC ...........................................................3-40
Ventilation Adjustment......................................3-20
Visors...........................................................2-12
11