2006 NISSAN XTERRA weight

2006 Nissan Towing Guide 13 TRAILER TONGUE/KING PIN LOAD
The amount of weight pressing down on the tow vehicle hitch is called trailer tongue load
(conventional trailer) or king pin load (5th wheel or gooseneck trailers). To measure trailer
tongue/king pin load, place the tongue of the trailer on a scale when the trailer is not
attached to the vehicle. A separate vehicle jack — not the trailer jack — should be used, as
the location of the trailer jack
is rearward of the trailer
tongue and will not give you
an accurate measurement of
the true tongue/king pin load.
Make sure the vehicle jack is
placed directly under the
trailer tongue coupler, and the
tongue is set at the
height/level of the tow vehicle
hitch.
For proper handling, keep conventional trailer tongue load between 10-15% of the
actual trailer weight, within the limits of the maximum trailer tongue load allowable. For
example, to determine the proper trailer tongue load for a 1,500-lb. trailer, multiply the
weight of 1,500 lbs. by 10% to arrive at a figure of 150 lbs.
5th wheel and gooseneck trailer king pin load should be kept between 15-25% of the
actual trailer weight.
See the SPECIFICATIONS section of this guide, or refer to your vehicle owner’s manual
to view the maximum conventional trailer tongue load listed for your vehicle.
NOTE – Conventional trailer tongue load must be more than 10% but not over 15% of the
total trailer weight. King pin load must be more than 15% but not over 25% of the total
trailer weight. The vehicle weight ratings (GVWR, GAWR, GCWR, etc.) must not be
exceeded, regardless of trailer or hitch type.

HITCH HEIGHT/TRAILER HEIGHT
It is important that your trailer floor and
tongue ride as level as possible. This will help
prevent over-angling, bottoming-out, and
improper load transfer. Therefore, the hitch or
trailer tongue should be adjusted during the
initial vehicle/trailer fit-up to ensure a level
ride. Ball mounts are available in different
configurations to change the hitch ball height.

2006 Nissan Towing Guide 14 TIRE PRESSURE
When towing a trailer, increase tow vehicle tire pressures to the recommended cold
specifications. You’ll find these figures in the owner’s manual and on the tire pressure chart
located in the vehicle. Trailer tire condition, size, load rating, and inflation pressure should
be in accordance with the trailer and tire manufacturer’s specifications.


TOWING
SAFETY

Towing can dramatically alter the handling and performance characteristics of your vehicle.
Plus, it puts increased strain on the engine and drivetrain. Therefore, it is always a good
idea to approach towing from the standpoint of safety — whether you’re purchasing
equipment or actually pulling the trailer.
Always make sure your vehicle’s towing capacity is adequate for the trailer you intend to
tow. Buy or lease only quality equipment, and have it installed only by professionals.
In addition, be certain that you have all of the equipment needed for safe towing,
including safety chains/cables, electric trailer brakes, electric trailer brake controller,
breakaway switch, extended rear view mirrors, and so on. All of these items have been
discussed in a previous section of this guide.
With regard to vehicle maintenance, you should follow a more frequent schedule, and
check fluid levels, pressures, tire condition, etc., more often when on the road. See your
owner’s manual for details.

LOADING YOUR TRAILER
Taking the time to load and balance your trailer properly will improve overall handling and
minimize the strain on your tow vehicle. Incorrectly loaded trailers tend to sway or swing
from side to side, upsetting vehicle handling. Careful loading and balancing can help
eliminate these problems.
As mentioned earlier, conventional trailer tongue load should fall between 10-15% of
the total trailer weight, and king pin load — if using a 5th wheel or gooseneck trailer —
should be between 15-25% of the total trailer weight. Excessive tongue/king pin load can
actually push the vehicle down in back, lifting the front wheels to a point where traction,
steering response, and braking are severely reduced. Insufficient tongue/king pin load can
cause instability, which may lead to “tail wagging” or jackknifing.

2006 Nissan Towing Guide 15 With this in mind, proper loading is
extremely important. When loading a trailer,
60% of the total cargo weight should be
positioned in the front portion of the trailer
and 40% in the back. Then, the load should
be adjusted until the proper tongue/king pin
load ratio is achieved.
The trailer load should be balanced
equally from side-to-side. Unequal side-to-
side loading can negatively affect handling
and braking. Once in place, all cargo should
be firmly secured to prevent shifting. If the
load should shift abruptly during braking or
cornering, it could quickly affect the
handling of your vehicle and cause a very
unsafe situation.
Finally, do not carry flammable materials,
such as gasoline, in your trailer. In the event
of an accident, an explosion or fire could
occur.

ENSURING VEHICLE/TRAILER STABILITY
Improper loading, excessive or insufficient trailer tongue/king pin load, overloading,
excessive trailer weight, poorly designed trailer suspensions, crosswinds, and poor
maintenance are all things that can affect the stability of your vehicle/trailer combination.
If swaying does occur, check the cargo load for proper balance and distribution to
ensure proper trailer tongue/king pin load. In addition, check the condition of the
suspension and shocks, as well as the tires, tire pressures, and wheel bearings on both the
tow vehicle and the trailer. If swaying occurs because of high winds or poor weather
conditions, wait until these conditions improve before resuming your trip.
If the swaying continues and you feel your trailer is suitably balanced and within the
towing capacity limits of your vehicle, discontinue towing and consult your Nissan dealer or
trailer manufacturer to determine the problem. Most important, do not tow until the problem
is corrected.

2006 Nissan Towing Guide 17
TOWING
TIPS

If you’ve never towed a trailer before, be aware that it does take getting used to. To begin
with, towing noticeably affects your vehicle’s performance:
Š It will not accelerate as quickly — an important point to keep in mind when merging onto
a highway.
Š It will not stop as quickly. Leave more room than usual between you and the traffic
ahead, and brake sooner when coming to a stop.
Š Abrupt maneuvering can unbalance the load and reduce the handling stability of your
tow vehicle. Plan ahead and make lane changes and turns smoothly.
If possible, before you actually hit the open road, practice towing in a large, uncrowded
area such as a stadium or shopping center parking lot. Become especially familiar with
backing up a trailer — the maneuver many people find most difficult.

REDUCE SPEED
Drive your vehicle at a moderate speed, and remember to reduce your speed in unsafe or
less-than-ideal road conditions or weather. The tendency for a trailer to sway increases
with speed, and such swaying can result in a loss of control.

BRAKE SOONER
The combination of your tow vehicle and trailer obviously requires a greater distance to
stop. A good rule of thumb to remember is that for each 10 mph of speed, allow yourself
one tow vehicle and trailer length of distance between the front of your vehicle and the
vehicle ahead.
When braking, use firm but gradual pressure on the pedal rather than panic braking.
Applying the brakes abruptly or with too much force can cause the trailer to skid or
jackknife at its point of attachment with the vehicle. This, in turn, can throw the tow vehicle
out of control.
If equipped with an electric trailer brake controller, follow the recommended operational
instructions.

PASS CAREFULLY
As mentioned in the introduction to this section, because of the added weight of the trailer,
acceleration capability is reduced and you’ll require a longer distance to pass another
vehicle. Be certain you have sufficient time and space to pass safely. Obviously, never
attempt passing on hills or when going around curves.

2006 Nissan Towing Guide 19 AUTOMATIC CRUISE CONTROL
Do not use cruise control while towing a trailer.

TOW MODE (IF EQUIPPED)
Tow Mode should be used when the vehicle and trailer weight is at least 75% of the
vehicle GCWR. This mode is most useful when towing a heavy trailer or hauling a heavy
load, particularly when stop-and-go traffic, rolling terrain, or a busy parking lot is involved.
Driving the vehicle in Tow Mode with minimal trailer load will not cause any damage;
however, fuel economy may be reduced, and transmission/engine driving characteristics
may feel different.

HILLS – UPGRADES
As the incline increases, shift down to a lower gear to maintain speed and prevent the
engine from lugging. However, for long and steep grades, do not stay in first gear when
driving above 35 mph or in second gear above 58 mph.* The added weight of a trailer
places an increased load on the engine and cooling system, so monitor your coolant
temperature gauge and automatic transmission fluid temperature gauge (if equipped) very
carefully. At the first sign of overheating, pull to the side of the road. See IF YOUR ENGINE
OVERHEATS later in this section for more information.

HILLS – DOWNGRADES
While going downhill, the weight of the trailer pushing on the tow vehicle may decrease
overall stability. Therefore, to maintain adequate control, reduce your speed and shift
to a lower gear.
When descending a hill, also avoid long or repeated use of the brakes as this reduces
their effectiveness and could cause overheating. Shifting to a lower gear instead provides
“engine braking” and reduces the need to brake as frequently.

IF YOUR ENGINE OVERHEATS
A moderate increase in engine operating temperature is normal when towing a trailer. If,
however, the coolant temperature gauge reading is abnormally high, or if you are
experiencing a significant loss of power, or if you hear unusual engine noises,** the engine
may be overheating and you should immediately take the following steps:

1. Pull your vehicle safely over to the side of the road, out of traffic. Apply the parking
brake, and move the gearshift lever to NEUTRAL (manual) or PARK (automatic). DO
NOT STOP THE ENGINE.

*For Murano, see your owner’s manual for information applicable to your vehicle.
**See your owner’s manual for additional indications that your vehicle may be overheating.

2006 Nissan Towing Guide 21
TOWING
GLOSSARY
5TH WHEEL
HITCH Located just forward of the rear axle centerline, this hitch uses a king pin to serve
as the pivot point for the trailer.
BALL MOUNT A bar that holds the hitch ball and is inserted into the hitch receiver. Also
commonly called a drawbar or “stinger.”
BREAKAWAY SWITCH A safety device using a trailer battery that automatically applies the trailer’s
brakes if it should accidentally become separated from the tow vehicle. A
breakaway switch may be used with both electric or surge trailer brake systems.
BUMPER HITCH A reinforced bumper designed to accommodate a hitch ball.
ELECTRIC TRAILER
BRAKES When the brakes on a tow vehicle are applied, an electric current is sent to an
actuator which applies the trailer’s brakes.
ELECTRIC TRAILER
BRAKE CONTROLLER A device that controls the electric trailer brakes.
GOOSENECK HITCH Located just forward of the rear axle centerline, this hitch uses a ball to serve as
the pivot point for the trailer.

GROSS AXLE
WEIGHT RATING (GAWR) The maximum amount of weight each vehicle axle (front and rear) is designed to
safely carry.
GROSS COMBINED
WEIGHT RATING (GCWR) The maximum allowable combined weight of the vehicle and trailer, including
passengers and all cargo.
GROSS VEHICLE
WEIGHT RATING (GVWR) The maximum allowable weight of the vehicle, including passengers, cargo, fuel,
hitch, trailer tongue load, and any optional equipment.
KING PIN
LOAD The amount of trailer (5th wheel or gooseneck) weight pressing down on the tow
vehicle hitch.

HITCH BALL
A ball that connects the trailer to the tow vehicle hitch and provides the means
by which the trailer pivots during cornering. Available in a number of sizes and
weight capacities, it must correspond to the trailer coupler size, and have a
sufficient capacity rating for the trailer being pulled.
RECEIVER HITCH A frame- or structure-mounted hitch with a receiver that allows removal of the
ball mount.
SAFETY CHAINS/CABLES Provides an emergency connection between the tow vehicle and the trailer,
should the trailer become disengaged for any reason.
SURGE BRAKES
Hydraulic-type braking system activated by inertia. As the tow vehicle begins to
brake, the trailer pushes against the hitch ball, consequently activating the trailer
brakes.
TRAILER TONGUE/COUPLER The part of the trailer that extends forward to meet the tow vehicle, and also
carries the coupler assembly.

TRAILER TONGUE
LOAD The amount of trailer (conventional) weight pressing down on the tow vehicle
hitch.
WEIGHT-DISTRIBUTING HITCH
SYSTEM Type of hitch system that helps shift the trailer tongue weight to all trailer tires
and the tow vehicle front tires. Strongly recommended when towing trailers with
a Maximum Trailer Weight greater than 5,000 lbs.
WIRING HARNESS
Provides an electrical connection linking the tow vehicle’s electrical system to
the trailer’s system.

2006 Nissan Towing Guide 22
SPECIFICATIONS

TOWING CAPACITIES
SUV’s, Trucks, and Minivans

























2006 ARMADA TOWING DATA
Engine Type 5.6L V8
Transmission A/T
Model(s) 4x2 4x4
without optional tow package 6,500 6,500 Maximum Trailer Weight1
(lbs.) with optional tow package4 9,100 9,000
without optional tow package 650 650 Maximum Trailer Tongue Load (lbs.) with optional tow package4 910 900
without optional tow package 12,800 13,000 Gross Combined Weight Rating (lbs.) with optional tow package4 14,600 14,822
Additional RECOMMENDED
Equipment4
Weight-Distributing Hitch Ball Mount (Class IV)
2006 FRONTIER TOWING DATA
Engine Type 2.5L 4-Cylinder 4.0L V6
Transmission A/T & M/T
Model(s) King Cab 4x2 King Cab 4x2 Crew Cab 4x2 King Cab 4x4 Crew Cab 4x4
Maximum Trailer Weight1, 3
(lbs.) 3,500 6,500 6,300 6,300 6,100
Maximum Trailer Tongue Load3
(lbs.) 350 650 630 630 610
Gross Combined Weight Rating (lbs.) 7,936 11,133 11,133 11,133 11,133
Additional RECOMMENDED
Equipment4 Weight-Distributing Hitch Ball Mount (Class IV)
2006 MURANO TOWING DATA
Engine Type 3.5L V6
Transmission CVT
Maximum Trailer Weight1 (lbs.) 3,500
Maximum Trailer Tongue Load (lbs.) 350
Gross Combined Weight Rating (lbs.) 8,100

2006 Nissan Towing Guide 23



















2006 TITAN TOWING DATA
Engine Type 5.6L V8
Transmission A/T
4x2 4x4
King Cab Crew Cab King Cab Crew Cab
WITH OPTIONAL TOWING PACKAGE4
Model(s)
XE SE LE
XE SE LE XE SE LE XE SE LE
Maximum Trailer
Weight1, 2 (lbs.) 9,500 9,500 9,200 9,400 9,400 9,200 9,400 9,400 9,200 9,400 9,300 9,200
Maximum Trailer
Tongue Load2 (lbs.) 950 950 920 940 940 920 940 940 930 940 930 920
Gross Combined Weight Rating (lbs.) 14,650 14,650 14,650 14,65014,65014,650 14,822 14,822 14,822 14,822 14,82214,822
WITHOUT OPTIONAL TOWING PACKAGE
Maximum Trailer
Weight1, 2 (lbs.) 6,500 7,400 7,200 6,500 7,400 7,200 6,500 7,400 7,200 6,500 7,400 7,200
Maximum Trailer
Tongue Load2 (lbs.) 650 740 720 650 740 720 650 740 720 650 740 720
Gross Combined Weight Rating (lbs.) 12,800 12,800 12,800 12,80012,80012,800 13,000 13,000 13,000 13,000 13,00013,000
Additional RECOMMENDED
Equipment4
Weight-Distributing Hitch Ball Mount (Class IV)

NOTE – For Titan, the Maximum Trailer Weight and Gross Combined Weight ratings for 5th
wheel and gooseneck trailer towing are the same as specified for conventional trailer towing
(above).
2006 PATHFINDER TOWING DATA
Engine Type 4.0L V6
Transmission A/T
Model(s) 4x2 & 4x4
Maximum Trailer Weight1 (lbs.) 6,000
Maximum Trailer Tongue Load (lbs.) 600
Gross Combined Weight Rating (lbs.) 11,133
Additional RECOMMENDED
Equipment4 Weight-Distributing Hitch Ball Mount (Class IV)
2006 QUEST TOWING DATA
Engine Type 3.5L V6
Transmission A/T
Maximum Trailer Weight1 (lbs.) 3,500
Maximum Trailer Tongue Load (lbs.) 350
Gross Combined Weight Rating (lbs.) 8,500