WARNING
Be careful not to allow your hands,
hair, jewelry or clothing to come into
contact with, or to get caught in the
cooling fan, or drive belt.
The engine cooling fan can start at
any time when the coolant tempera-
ture is high.
7. After the engine cools down, check the cool-
ant level in the reservoir tank with the engine
running. Add coolant to the reservoir tank if
necessary. Have your vehicle repaired at the
nearest NISSAN dealer.When towing your vehicle, all provincial and
local regulations for towing must be followed.
Incorrect towing equipment could damage your
vehicle. Towing instructions are available from a
NISSAN dealer. Local service operators are
generally familiar with the applicable laws and
procedures for towing. To assure proper towing
and to prevent accidental damage to your ve-
hicle, NISSAN recommends having a service
operator tow your vehicle. It is advisable to have
the service operator carefully read the following
precautions.
WARNING
Never ride in a vehicle that is being
towed.
Never get under your vehicle after it
has been lifted by a tow truck.
CAUTION
When towing, make sure that the
transmission, axles, steering system
and powertrain are in working condi-
tion. If any unit is damaged, dolliesmust be used.
Always attach safety chains before
towing.TOWING YOUR VEHICLE
6-10
In case of emergency
06.4.14/T30-J/V5.0
7 Appearance and careCleaning exterior ................................................................... 7-2
Washing ............................................................................ 7-2
Removing spots .............................................................. 7-2
Waxing ............................................................................... 7-2
Glass .................................................................................. 7-3
Underbody ........................................................................ 7-3
Aluminum alloy wheels .................................................. 7-3
Chrome parts ................................................................... 7-3
Tire dressing .................................................................... 7-3
Plastic parts ..................................................................... 7-3
Cleaning interior .................................................................... 7-4Floor mats ......................................................................... 7-4
Glass .................................................................................. 7-5
Seat belts ......................................................................... 7-5
Luggage floor board ........................................................ 7-5
Corrosion protection ............................................................ 7-5
Most common factors contributing to vehicle
corrosion ........................................................................... 7-5
Environmental factors influence the rate of
corrosion ........................................................................... 7-5
To protect your vehicle from corrosion ..................... 7-6
06.4.14/T30-J/V5.0
GLASSUse glass cleaner to remove smoke and dust film
from the glass surfaces. It is normal for glass to
become coated with a film after the vehicle is
parked in the hot sun. Glass cleaner and a soft
cloth will easily remove this film.
CAUTION
When cleaning the inside of the win-
dows, do not use sharp-edged tools,
abrasive cleaners or chlorine-based dis-
infectant cleaners. They could damage
the electrical conductors, such as radio
antenna elements or rear window de-
froster elements.SEAT BELTSThe seat belts can be cleaned by wiping them
with a sponge dampened in a mild soap solution.
Allow the belts to dry completely before using
them.
WARNING
Do not allow wet belts to roll up in theretractor. NEVER use bleach, dye, or
chemical solvents since these may se-
verely weaken the seat belt webbing.
LUGGAGE FLOOR BOARDThe luggage floor board can be washed. To
wash the luggage floor board, remove it from the
luggage area. (See “LUGGAGE FLOOR
BOARD” in the “2. Instruments and controls”
section.)
CAUTION
Never use benzine, thinner or any
similar material for washing the lug-
gage floor board.
Wipe the luggage floor board dry
before putting it back in the vehicle.
MOST COMMON FACTORS
CONTRIBUTING TO VEHICLE
CORROSIONThe accumulation of moisture-retaining dirt
and debris in body panel sections, cavities,
and other areas.
Damage to paint and other protective coat-
ings caused by gravel and stone chips or
minor traffic accidents.ENVIRONMENTAL FACTORS
INFLUENCE THE RATE OF
CORROSION
MoistureAccumulation of sand, dirt and water on the
vehicle body underside can accelerate corro-
sion. Wet floor coverings will not dry completely
inside the vehicle, and should be removed for
drying to avoid floor panel corrosion.Relative humidityCorrosion will be accelerated in areas of high
relative humidity, especially those areas where
the temperatures stay above freezing and where
atmospheric pollution exists and road salt is
used.CORROSIONPROTECTION
Appearance and care
7-5
06.4.14/T30-J/V5.0
8 Maintenance and do-it-yourselfMaintenance requirements ................................................. 8-2
Scheduled maintenance ............................................... 8-2
General maintenance ..................................................... 8-2
Where to go for service ................................................ 8-2
General maintenance ........................................................... 8-2
Explanation of general maintenance items ............... 8-2
Maintenance precautions .............................................. 8-5
Engine compartment check locations ............................. 8-7
Engine cooling system ........................................................ 8-8
Checking engine coolant level .................................... 8-8
Changing engine coolant ............................................. 8-9
Engine oil ............................................................................. 8-10
Checking engine oil level ........................................... 8-10
Changing engine oil .................................................... 8-11
Changing engine oil filter ........................................... 8-12
Automatic transmission fluid ........................................... 8-13
Power steering fluid .......................................................... 8-14
Brake and clutch fluid ....................................................... 8-14
Window washer fluid ........................................................ 8-15
Battery ................................................................................... 8-16
Jump starting ................................................................. 8-17
Drive belts ............................................................................ 8-17
Spark plugs ......................................................................... 8-18Replacing spark plugs ................................................ 8-18
Air cleaner ............................................................................ 8-18
Windshield wiper blades ................................................. 8-19
Cleaning ......................................................................... 8-19
Replacing ....................................................................... 8-20
Parking brake and brake pedal ...................................... 8-21
Checking parking brake ............................................. 8-21
Checking brake pedal ................................................. 8-21
Brake booster ................................................................ 8-22
Fuses ..................................................................................... 8-22
Engine compartment ................................................... 8-23
Passenger compartment ............................................ 8-24
Keyfobbattery replacement ............................................ 8-24
Lights ..................................................................................... 8-26
Headlights ...................................................................... 8-27
Headlight aim ................................................................ 8-28
Exterior and interior lights .......................................... 8-30
Wheels and tires ................................................................ 8-34
Tire pressure ................................................................. 8-34
Tire labeling ................................................................... 8-37
Types of tires ................................................................. 8-39
Tire chains ...................................................................... 8-40
Changing wheels and tires ........................................ 8-41
06.4.14/T30-J/V5.0
corrosive materials, check lubrication frequently.
Lights*:
Clean the headlights on a regular basis. Make
sure that the headlights, stop lights, tail lights,
turn signal lights, and other lights are all operat-
ing properly and installed securely. Also check
headlight aim.
Road wheel nuts (lug nuts)*:
When checking the tires, make sure no wheel
nuts are missing, and check for any loose wheel
nuts. Tighten if necessary.
Tire rotation*:
Tires should be rotated every 7,500 miles
(12,000 km). However, the timing for tire rotation
may vary according to your driving habits and
road surface conditions.
Tires*:
Check the pressure with a gauge often and
always prior to long distance trips. If necessary,
adjust the pressure in all tires, including the
spare, to the pressure specified. Check carefully
for damage, cuts or excessive wear.
Tire, wheel alignment and balance:
If the vehicle should pull to either side while
driving on a straight and level road, or if you
detect uneven or abnormal tire wear, there maybe a need for wheel alignment.
If the steering wheel or seat vibrates at normal
highway speeds, wheel balancing may be
needed.
For additional information regarding tires, refer to
“Tire Safety Information” in the Warranty Infor-
mation Booklet (Canada).
Windshield:
Clean the windshield on a regular basis. Check
the windshield at least every six months for
cracks or other damage. Have a damaged wind-
shield repaired by a qualified repair facility.
Windshield wiper blades*:
Check for cracks or wear if they do not wipe
properly.
Inside the vehicleThe maintenance items listed here should be
checked on a regular basis, such as when
performing periodic maintenance, cleaning the
vehicle, etc.
Accelerator pedal:
Check the pedal for smooth operation and make
sure the pedal does not catch or require uneven
effort. Keep the floor mats away from the pedal.Brake pedal and booster*:
Check the pedal for smooth operation and make
sure it has the proper distance under it when
depressed fully. Check the brake booster func-
tion. Be sure to keep floor mats away from the
pedal.
Brakes:
Check that the brakes do not pull the vehicle to
one side when applied.
Parking brake*:
Check that the lever has the proper travel and
make sure that the vehicle is held securely on a
fairly steep hill when only the parking brake is
applied.
Seat belts:
Check that all parts of the seat belt system (for
example, buckles, anchors, adjusters and retrac-
tors) operate properly and smoothly, and are
installed securely. Check the belt webbing for
cuts, fraying, wear or damage.
Seats:
Check seat position controls such as seat ad-
justers, seatback recliner, etc. to ensure they
operate smoothly and that all latches lock se-
curely in every position. Check that the head
restraints move up and down smoothly and that
Maintenance and do-it-yourself
8-3
06.4.14/T30-J/V5.0
the locks hold securely in all latched positions.
Steering wheel:
Check for changes in the steering conditions,
such as excessive free play, hard steering or
strange noises.
Warning lights and chimes:
Make sure that all warning lights and chimes are
operating properly.
Windshield defroster:
Check that the air comes out of the defroster
outlets properly and in good quantity when
operating the heater or air conditioner.
Windshield wiper and washer*:
Check that the wipers and washer operate
properly and that the wipers do not streak.Under the hood and the vehicleThe maintenance items listed here should be
checked periodically (for example, each time you
check the engine oil or refuel).
Battery*:
Check the fluid level in each cell. It should be
between the upper level and lower level lines.
Vehicles operated in high temperatures or under
severe conditions require frequent checks of the
battery fluid level.Brake and clutch fluid level*:
Make sure that the brake and clutch fluid level is
between the MAX and MIN lines on the reservoir.
Engine coolant level*:
Check the coolant level when the engine is cold.
Engine drive belts*:
Make sure that no belt is frayed, worn, cracked
or oily.
Engine oil level*:
Check the level on the dipstick after parking the
vehicle on a level spot and turning off the engine.
Exhaust system:
Make sure there are no loose supports, cracks or
holes. If the sound of the exhaust seems unusual
or there is a smell of exhaust fumes, immediately
locate the trouble and correct it. (See “Precau-
tions when starting and driving” in the “5. Start-
ing and driving” section for exhaust gas (carbon
monoxide).)
Fluid leaks:
Check under the vehicle for fuel, oil, water or
other fluid leaks after the vehicle has been
parked for a while. Water dripping from the air
conditioner after use is normal. If you should
notice any leaks or if gasoline fumes are evident,check for the cause and have it corrected imme-
diately.
Power steering fluid level* and lines:
Check the level in the reservoir tank with the
engine off. Check the lines for proper attach-
ment, leaks, cracks, etc.
Radiator and hoses:
Check the front of the radiator and clean off any
dirt, insects, leaves, etc., that may have accumu-
lated. Make sure the hoses have no cracks,
deformation, deterioration or loose connections.
Underbody:
The underbody is frequently exposed to corro-
sive substances such as those used on icy roads
or to control dust. It is very important to remove
these substances, otherwise rust will form on the
floor pan, frame, fuel lines and around the ex-
haust system. At the end of winter, the under-
body should be thoroughly flushed with plain
water, being careful to clean those areas where
mud and dirt may accumulate. For additional
information, see “Cleaning exterior” in the “7.
Appearance and care” section.
Windshield washer fluid*:
Check that there is adequate fluid in the tank.8-4
Maintenance and do-it-yourself
06.4.14/T30-J/V5.0
MAINTENANCE PRECAUTIONSWhen performing any inspection or maintenance
work on your vehicle, always take care to prevent
serious accidental injury to yourself or damage to
the vehicle. The following are general precau-
tions which should be closely observed.
WARNING
Park the vehicle on a level surface,
apply the parking brake securely and
block the wheels to prevent the ve-
hicle from moving. For a manual
transmission, move the shift lever to
the N(Neutral) position. For an auto-
matic transmission, move the selec-
tor lever to the P (Park) position.
Be sure the ignition key is in the OFF
or LOCK position when performing
any parts replacement or repairs.
Your vehicle is equipped with an au-
tomatic engine cooling fan. It may
come on at any time without warning,
even if the ignition key is in the OFF
position and the engine is not run-
ning. To avoid injury, always discon-nect the negative battery cable be-
fore working near the fan.
If you must work with the engine
running, keep your hands, clothing,
hair and tools away from moving
fans, belts and any other moving
parts.
It is advisable to secure or remove
any loose clothing and any jewelry,
such as rings, watches, etc. before
working on your vehicle.
Always wear eye protection when-
ever you work on your vehicle.
If you must run the engine in an
enclosed space such as a garage, be
sure there is proper ventilation for
exhaust gases to escape.
Never get under the vehicle while it is
supported only by a jack. If it is nec-
essary to work under the vehicle,
support it with safety stands.
Keep smoking materials, flame and
sparks away from fuel and the
battery.On gasoline engine models with the
Multiport Fuel Injection (MFI) Sys-
tem, the fuel filter or fuel lines should
be serviced by a NISSAN dealer be-
cause the fuel lines are under high
pressure even when the engine is off.
CAUTION
Do not work under the hood while
the engine is hot. Turn off the engine
and wait until it cools down.
Never connect or disconnect either
the battery or any transistorized
component connector while the igni-
tion key is on.
Never leave any engine or automatic
transmission related component har-
ness connectors disconnected while
the ignition key is on.
Avoid direct contact with used engine
oil and coolant. Improperly disposed
engine oil, engine coolant and/or
other vehicle fluids can hurt the envi-
Maintenance and do-it-yourself
8-5
06.4.14/T30-J/V5.0
requires coolant, have it checked by a
NISSAN dealer.
CHANGING ENGINE COOLANTMajor cooling system repairs should be per-
formed by a NISSAN dealer. The service
procedures can be found in the appropriate
NISSAN Service Manual.
Improper servicing can result in reduced
heater performance and engine overheating.
WARNING
To avoid being scalded, never change
the coolant when the engine is hot.Never remove the radiator cap when
the engine is hot. Serious burns
could be caused by high pressure
fluid escaping from the radiator.
Avoid direct skin contact with used
coolant. If skin contact is made, wash
thoroughly with soap or hand cleaner
as soon as possible.
Keep coolant out of reach of children
and pets.
1. Open radiator drain valve
Aat the bottom of
radiator, and remove radiator filler cap
B.
Be careful not to allow coolant to con-
tact drive belts.
Waste coolant must be disposed of
properly. Check your local regulations.
2. Close the radiator drain valve securely after
the coolant is drained.
3. Fill the radiator slowly with the proper mixture
of antifreeze solution and demineralized
water/distilled water. Fill the reservoir tank up
to the MAX level. Then install the radiator filler
cap.
SDI1080D
Maintenance and do-it-yourself
8-9
06.4.14/T30-J/V5.0