2006 MITSUBISHI LANCER steering column

AC210969AD
Clip
Steering column
shaft
STE E RING C O LUMN SHAFT AS SEMBL Y
POWER STEERING37-21
2.Pin c h t he st eering column shaf t clip with pliers,
an d pull up the shaf t towards the d i rection shown
to disengag e the steering column shaf t assembly .
INSTALLA T ION SER VICE POINT
>>A<< STEERING COLUMN SHAFT
ASSEMBL
Y INST ALLA TION
CAUTION
•When reusing the steering column, do not
release the tilt lever until the steering column
shaft has been installed.
•When the steering column is replaced, do not
release the tilt lever until it has been installed.
Do not remove the tilt lever fixing band until
the installation has completed.
•When installing the steering column, do not
leave it fixed temporarily at only one point
and make sure the column shaft is not shaken
strongly. If you fail to do, the collision absorb
-
ing mechanism at the column shaft mounting
location may be damaged.
AC209383AD
14
3 2
Tilt lever
Ensure that the tilt lever is in the lock position, and
install the steering column. Tighten the four bolts in
the order shown by hand, and then tighten them to
the specified torque in the order shown.
Tightening torque: 12 ± 2 N⋅m

STEERING COLUMN SHAFT ASSEMBLY
POWER STEERING37-22
DISASSEMBLY AND REASSEMBLY
M1372015000068
AC210967AD
3
2
14
Disassembly steps
<>>>A<<1.Special bolt
>>A<<2.Steering lock bracket
>>A<<3.Steering lock cylinder assembly
4.Steering column shaft assembly
DISASSEMBL
Y SER V ICE POINT
<> SPECIAL BOLT REMOV A L
ACX01138
AB
Steering lock
bracket
Reverse screw tap
Special bolt
Steering lock
cylinder
1. Drill in the special bo lt a ho le de ep enou gh for th e
t ap t o st and.
2.Remove the special b o lt with a lef t -h and t ap.
REASSEMBL Y SER V ICE POINT
>>A<< STEERING LOCK CYLINDER
ASSEMBL
Y /STEERING LOCK
BRACKET/SPECIAL BOL
T INST ALLA
-
TION
CAUTION
The steering lock bracket and bolts must be
replaced with new ones when the steering lock is
installed.
1. When installing the steering lock cylinder assembly and steering lock bracket to the column
tube, temporarily install the steering lock in
alignment with the column boss.
ACX01139 AB
2. After checking that the lock works properly,
tighten the special bolts until the head twists off.

AC300427
1
AD
AC301737AB
2 3
,
2
3

AC300429 AB
2
Junction
block
AC206768 AD
3
16
,
3
16

AC301742 AB
4
Glove box
AC301741AB
5
Diagnosis
connector
AC100195
6
AC
Windshield
wiper arm

AC212109AC
6Steering column
shaft assembly
EARTH
COMPONENT LOCA
TIONS70-17

DASH PANEL
CONFIGURATION DIAGRAMS80-30
DASH PANEL (CONTINUED)
AC301179
Connector
symbol
-201
thru
-227
C
AB
STEERING COLUMN
C-207
C-206 C-201
C-202
C-203C-203
C-204
C-205 Instrument panel
wiring harness
Clock spring
Y
C-201(6)Ignition switch
C-202(7)Key reminder switch
C-203(10)Column switch
C-204(6)Clock spring
C-205(4-Y)Clock spring
C-206(1)Horn switch
C-207(2)Air bag module (squib)
C-208(13)Instrument panel wiring harness and J/B
combination
C-209(14)Instrument panel wiring harness and J/B
combination
C-210(6)Instrument panel wiring harness and J/B
combination
C-211(1-B)Instrument panel wiring harness and J/B
combination
C-212(28)Instrument panel wiring harness and J/B
combination

DASH PANEL
CONFIGURATION DIAGRAMS80-36
DASH PANEL (CONTINUED)
AC206572
Connector
symbol
-201
thru
-227
C
AC
STEERING COLUMN
C-207
C-206
C-205
C-204
C-203C-203
C-202
C-201
Instrument panel
wiring harness
Clock spring
Y
C-201(6)Ignition switch
C-202(7)Key reminder switch
C-203(10)Column switch
C-204(6)Clock spring
C-205(4-Y)Clock spring
C-206(1)Horn switch
C-207(2)Air bag module (squib)
C-208(13)Instrument panel wiring harness and J/B
combination
C-209(14)Instrument panel wiring harness and J/B
combination
C-210(6)Instrument panel wiring harness and J/B
combination
C-211(1-B)Instrument panel wiring harness and J/B
combination
C-212(28)Instrument panel wiring harness and J/B
combination