2006 MITSUBISHI LANCER IX Bumper

FRONT BUMPER ASSEMBLY
EXTERIOR51-3
FRONT BUMPER ASSEMBLY
ADHESIVEM1511000501195
ItemSpecification
Front three-diamond markDouble-sided tape: Generic products
0.8 mm thickness
FRONT BUMPER ASSEMBLY
REMOVAL AND INSTALLATIONM1511001401124
AC504557
AC300466
Y0534AU
AC405706
AB
2
4
5
5
3 1
C
C
B
B
A
A
A
AA
A
A
A
3
2
Section A – A
3
Clip
Front end
crossmember
Clip
Section B – B
5
3
Section C – C
Removal steps
1.Splash shield mounting clips
2.Radiator grille assembly
•Fog lamp connector connection
3.Front bumper assembly
4.Front bumper beam assembly
5.Front bumper fixing clip
Removal steps (Continued)

FRONT BUMPER ASSEMBLY
EXTERIOR51-4
DISASSEMBLY AND REASSEMBLY
M1511001601128
AC504558AB
Double-sided tape: Generic products
0.8 mm thickness
1
1
12
13
14
11
10
10
4
7
7
6
6
8
9
8
5
3N
N
N
2
Removal steps
1.Front three-diamond mark
2.Under duct
3.Air intake bezel fog lamp>
4.Front fog lamp sup port front fog lamp>
5.Front fog lamp bezel front fog lamp>
<>>>A<<6.Rivets
7.Front bumper side plate
8.Radiator grille
9.Radiator centre grille
10.Front bumper garnish
11 .Front bumper extension
12.Front bumper nut
13.Licence plate garnish
14.Front bumper face
Removal steps (Continued)

FRONT BUMPER ASSEMBLY
EXTERIOR51-5
DISASSEMBLY SERVICE POINT
<> RIVETS REMOVAL
AC100411AB
Rivet
Drill
Bumper face
Use a d r ill (4.0 mm) to make a h o le in the rive t to
break it, an
d then remo ve th e rivet.
REASSEMBL Y SER V ICE POINT
>>A<< RIVETS ASSEMBL Y
AC305178AC
1
2
3
4 Portion A
Rivet
Rivet tool
Flange
Rivet
Front bumper
side plate
Rivet tool
Front bumper
face
Front bumper face
Use the rive t tool sho w n in th e illustration to att a ch
the rivet b
y the following p r oced ures.
1. Insert t he rivet in to t he f r ont bumpe r f a ce an d front
bu m p er s i de p l at e .
2.Place t he rivet too l over port i on A o f the rivet.
3.Wh ile push i ng t he fla nge surface of th e rivet with
th e rivet too l , press t he han dle o f the to ol.
4.Th e thin p a rt o f portio n A is cut out an d the rivet is
h e ld in position.

REAR BUMPER ASSEMBLY
EXTERIOR51-6
REAR BUMPER ASSEMBLY
REMOVAL AND INSTALLATIONM1511001901022
Pre-removal and Post-installation Operation
•Rear Combination Light Removal and Installation.
(Refer to GROUP 54A, Rear Combination Lamp
P.54A-82.)
•Rear End Trim Removal and Installation. (Refer to
GROUP 52A, Trims
P.52A-13.)
•Rear Splash Shield Removal and Installation.
AC300411
AC300412
AC504608
Clip
Rear bumper assembly Section A – A
Section B – B
Clip
Rear bumper assembly
Rear bumper assembly
AB
B
B
A
A
A
A

AC504610
A
A
B
B
C
C
Clip
Clip
Rear bumper
assembly
Rear bumper
assembly
Rear bumper
assembly
Clip
Section A – A
Section B – B
Section C – C
Rear bumper assembly

AB

REAR BUMPER ASSEMBLY
EXTERIOR51-7
DISASSEMBLY AND REASSEMBLY
M1511002100640
AC504609
1
2
9
N
3
8
4
5
6
AB

AC504611
1
2
9
N
3
8
4
5
7
6
AB

Disassembly steps
<>>>A<<1.Rivets
2.Rear bumper side plate assembly
3.Rear bumper centre reinforcement
4.Rear fog lamp bracket
5.Rear fog lamp assembly
6.Rear fog lamp bezel
7.Extension
8.Rear bumper extension
9.Rear bumper face
Disassembly steps (Continued)

MOULDINGS
EXTERIOR51-8
DISASSEMBLY SERVICE POINT
<> RIVETS REMOVAL
AC100411AB
Rivet
Drill
Bumper face
Use a d r ill (4.0 mm) to make a h o le in the rive t to
break it, an
d then remo ve th e rivet.
ASSEMBLY SER V ICE POINT
>>A<< RIVETS ASSEMBL Y
Y0412AU
AC00587618E0192AE
1
2
3
4 Portion A
Rivet
Flange
Rivet
Rear bumper
side plate
Rear bumper
face
Rear bumper face
Rivet tool
Rivet tool
Use the rive t tool sho w n in th e illustration to att a ch
the rivet b
y the following p r oced ures.
1.In sert the rivet into the rea r bumper fa ce a nd rea r
bu m p er s i de p l at e .
2.Place t he rivet too l over port i on A o f the rivet.
3.Wh ile push i ng t he fla nge surface of th e rivet with
th e rivet too l , press t he han dle o f the to ol.
4.Th e thin p a rt o f portio n A is cut out an d the rivet is
h e ld in position.
MOULDI NGS
SPECIAL T O OL
M151 100 0601 13 6
ToolNumberNameUse
MB990449
MB990449Window moulding removerRemoval of drip moulding

REAR SPOILER
EXTERIOR51-25
REAR SPOILER
REMOVAL AND INSTALLATIONM1511006100136
AC303713
2
3
4
2 1
AB
1
Removal steps
•Trunk lid bumper (Refer to GROUP
42, Trunk lid
P.42-43.)
1.Cap
2.Gasket
3.Rear spoiler
<>4.High-mounted stop lamp
REMOV A L SER V ICE POINT
< > HIGH-MOUNTED ST OP LAMP
REMOV
A L
Use the following step s to ea sily ro ute high-mounted
stop
lamp harne ss in the eve n t of inst allation:
CAUTION
Ensure that the string is tightly tied.
AC303708
Connector
String
AB
1. Tie string on high-mounted stop lamp harness (at
connector side).
2. Carefully pull out high-mounted stop lamp.

OVERALL CONFIGURATION DIAGRAM
CONFIGURATION DIAGRAMS80-2
OVERALL CONFIGURATION DIAGRAM
OVERALL WIRING DIAGRAM M1801000101261
AC301175AB
Front wiring
harness (RH) Control wiring
harness Instrument panel
wiring harness Roof wiring
harnessFloor wiring
harness (RH)
Battery wiring
harness Front wiring
harness (LH) Front door
wiring harness
Floor wiring
harness (LH) Fuel wiring
harnessRear door
wiring harness
Front bumper
wiring harness
Rear bumper
wiring harness
*
*
NO
TE: .
1.This illu stration shows o n ly major wirin g harne sses.
2.*: also eq uipp ed at t he rig h t side.