2006 MITSUBISHI COLT light

SUNROOF
BODY42-20
SUNROOF
M2420016000242
Electric sliding glass sunroof with tilt-up mechanism
has been adopted (Option). This sunroof features the
following characteristics.
•Lightweight sunroof have been adopted.
•The sunroof tilts up for approx. 30mm to improve
ventilation performance.
•The integrated switch allows for all slide
open/close, tilt up/down and stop operations.
•If external force is applied during slide closing or
tilt down operations that obstructs operations,
then the sunroof lid glass will stop according to
the jam prevention mechanism.
CONSTRUCTION DIAGRAM
AC206680 AB
Sunroof lid glass Drain hose
Drain hose
Sunroof motor assembly
(integrated into sunroof-ECU) Sunshade
Open switch
Tilt-up switch
Close/tilt-down switch
Drain hose
DESCRIPTION OF
STRUCTURE AND
OPERA
T ION
SUNROOF FUNCTION
The sunroof may operat e in the way similar to th e
jam preve
n tion function of the sunro o f due to so me
driving condition
s or environment. In the case, move
the sunroof t
o fully closed po sit i on a s described
below
.
1.T u rn ON and hold the sunroo f switch un til t he
sunroo f moves in the desired d i rection and stop s.
2.If the sunroof does not move to the fully closed
p o sit i on b y the operat ion in S t ep 1 and the jam
p r even tion f unction op erat es again, release the
sunroo f switch. Th en within the elap se of 3
seco nds, turn ON and ho ld it again until th e
sunroo f stop s at the fully closed position.
If the sunroof does not o perate corre ctly even af ter
step
2 is performed 4 times, re fer to th e W o rksh op
Manu
al.

GROUP 54A
CHASSIS
ELECTRICAL
CONTENTS
GENERAL INFORMATIO N . . . . . . . .54A-2
DIAGNOSIS SYSTEM . . . . . . . . . . . .54A-3
BATTERY . . . . . . . . . . . . . . . . . . . . . .54A-4
IMMOBILIZER SYSTEM . . . . . . . . . .54A-5
LIGHTING . . . . . . . . . . . . . . . . . . . . . .54A-7
COMBINATION METER . . . . . . . . . . .54A-10
CIGARETTE LIGHTER . . . . . . . . . . . .54A-13
RADIO, CD PLAYER, SPEAKER,
ANTENNA . . . . . . . . . . . . . . . . . . . . . .54A-14

GENERAL INFORMATION
CHASSIS ELECTRICAL54A-2
GENERAL INFORMATION
M2540000100302
FEATURES
IMPROVEMENT OF VISUAL OBSERVA-
TION AND SAFETY, AND ENHANCEMENT
OF USER-FRIENDLINESS AND VERSA
-
TILITY
•The large four headlamps with the lightweight
resin lenses have been adopted.
•The high-mounted stop lamp has been installed
on the tailgate for all models.
•Combination meters and ECUs are connected
using CAN to ensure the transmission of informa
-
tion.
•The combination meters are provided integrated
with a perfect round-shaped speedometer where
the needles operate at the wider angle.
IMPROVEMENTS IN SERVICE QUALITY
•Diagnosis connector for inspection with M.U.T.-III
is installed.
•Diagnosis and service data are integrated in the
combination meter, enabling communication with
M.U.T.-III
BETTER PRODUCT PACKAGE
•The smart wiring system (SWS) has been
adopted for the lamp control including the head
-
lamp auto turn-off and fog lamp unattended-oper-
ation reminder.

LIGHTING
CHASSIS ELECTRICAL54A-7
LIGHTING
M2540004000932
EXTERIOR LAMPS
•The headlamp employs a large four-lamp type
integrated with the front turn-signal lamp and
position lamp, creating the integrity appearance
with the hood. The internal lens design looks like
a precision machine, achieving improved appear
-
ance.
•The fog lamp is standard equipped. (VRX, VR
and RALLIART version-R : Standard equipment,
LS : Option)
•The rear combination lamps are a large verti-
cal-type integrated with the tail lamp, stop lamp,
rear turn-signal lamp and back-up lamp.
•The high-mounted stop lamp is equipped as
standard in order to improve safety.
Specifications
ItemSpecification
Headlamp assemblyHeadlamp (halogen bulb)Low-beam W55 (H7)
High-beam W55 (H1)
Position lamp W5 (W5W)
Front turn-signal lamp W21 (W21W)
Fog lamp W55 (H11)
Side turn-signal lamp W5 (WY5W)
Rear combination lamp
assemblyTa i l l a m p W5 (W5W)
Stop lamp W21 (W21W)
Rear turn-signal lamp W21 (W21W)
Back-up lamp W21 (W21W)
High-mounted stop lamp W x units5 × 4 (W5W)
Licence plate lamp W5 (W5W)
NOTE: The brackets ( ) show the bulb type.

LIGHTING
CHASSIS ELECTRICAL54A-8
CONSTRUCTION DIAGRAM
AC405170
Headlamp (high-beam)
Front turn-signal lamp
Position lamp Side turn-signal lamp
Headlamp assembly
AC
Headlamp (low-beam)
Fog lamp
AC510138AC
High-mounted stop lamp
Licence plate lamp Stop lamp
Reflector
Rear turn-signal
lamp
Back-up lamp Tail lamp
Rear combination lamp
assembly

LIGHTING
CHASSIS ELECTRICAL54A-9
INTERIOR LAMP
The lens-push type map and room lamp is adopted
so that an excellent operationability can be achieved
allowing operation from driver and passenger seats.
Specifications
ItemSpecification
Map and room lamp W × units8 × 2
CONSTRUCTION DIAGRAM
AC601455

Map and room lamp
Map and room lamp
AB

COMBINATION METER
CHASSIS ELECTRICAL54A-10
COMBINATION METER
M2540005000894
The combination meter features large, clearly visible
analogue indicators. The meter has the speedometer
in the middle, the coolant temperature gauge at
upper right, the fuel gauge at lower right, and the
tachometer at left so that drivers can easily distin
-
guish the information from the meters. The combina-
tion meter offers the following advantages.
•The combination meter is used for air conditioner
and meter drive control to integrate ECU.
•CAN communication is used for more reliable
transmission of all gauge data and indicator lamp
input signals, such as vehicle speed, engine
RPM, and coolant temperature. For further
details on CAN, refer to GROUP 54C, CAN
P.54C-2. The signals that the combination meter
uses are described in the CAN communications
input signals table
.
•Several diagnosis functions such as the diagno-
sis code memory and actuator tests are prepared
in order to improve serviceability.
•For a brighter display at night and for a longer
useful life, all indicator lamps, warning lamps, and
illumination bulbs use LEDs.
•The indicators for the speedometer, fuel gauge,
and other gauges are driven by a stepping motor.
For further details, consult the stepping motor
section
.
•The electronic speedometer operates by receiv-
ing vehicle speed signals sent by the
engine-ECU or engine-CVT-ECU
via the CAN.
•A large and clear LCD type odo-tripmeter is pro-
vided. The odometer continuously displays val-
ues while the tripmeter adopts a twin-trip (trip A,
trip B) function which is switched by a reset but
-
ton. In addition, clock function is incorporated.
•A fog lamp indicator lamp is provided to let the
driver know that the fog lamp is on.
•A seat belt warning lamp is installed to encourage
the driver to fasten the seat belt.
•The high-contrast meter is adopted. When the
ignition is turned ON, such as the needles and
face display are illuminated with fade-in lighting
by the LED light source.
•To further accentuate the high-contrast lighting,
the light of the high-contrast meter fades in and
fades out when the light is turned on and off
respectively.
•With the auto illumination function incorporated in
the high-contrast meter, a two-stage switching of
daytime (non-dimming) and nighttime (dimming)
is achieved. Also, the brightness can be adjusted
using the illumination control knob.
•A tail lamp indicator lamp is installed which
informs the lighting status of the tail lamps to the
driver.

CIGARETTE LIGHTER
CHASSIS ELECTRICAL54A-13
DIAGNOSIS CODE TABLE
Code No.Diagnostic item
U1073Bus Off
U1100Engine-ECU or engine-CVT-ECU time-out (related to
engine)
U1101Engine-CVT-ECU time-out (related to CVT)
U1102ABS-ECU or ASC-ECU time-out
U1106EPS-ECU time-out
U1109ETACS-ECU time-out
U1120Failure information on engine-ECU or engine-CVT-ECU
(related to engine)
U1206Flag invalid
CIGARETTE LIGHTER
M2540003300060
The cigarette lighter is installed to the centre lower
panel.
AC600730
Cigarette lighter Cigarette lighter


AC
Commun ication st andb y signalETACS-E C U
Driver's door "open" sign als
Ignition switch (ACC) signa l
Ignition switch (IG1 ) sig nal
High-beam indicator re quest signal
Tu rn-signal indicato r reque st signa l
Fog lamp indicator request signal
Illumination sig nal
All doors "Open" sign al
Signal T r a nsmitter ECU