2006 MERCEDES-BENZ SL65AMG clock

394 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to posi-
tion M (
page 123).

Open the hood (
page 272).
1Bulb socket for turn signal lamp
2High beam headlamp cover
3Low beam headlamp cover (Xenon or
Bi-Xenon* lamp). Do not remove.4High beam bulbs
5Locking mechanism
6Parking and standing lampsFront turn signal bulb

Turn bulb socket 1 counterclockwise
and pull it out.

Push the bulb into socket 1, turn
socket 1 counterclockwise and re-
move it.

Insert the new bulb in socket 1, push
and turn bulb socket 1 clockwise.

Reinsert bulb socket 1 in lamp and
turn bulb socket 1 clockwise.
Warning!
G
Do not remove the cover for the Xenon or
Bi-Xenon* headlamp. Because of high volt-
age in Xenon and Bi-Xenon* lamps, it is dan-
gerous to replace the bulb or repair the lamp
and its components. We recommend that
you have such work done by a qualified
technician.

395 Practical hints
Replacing bulbs
High beam/ high beam flasher bulbs
Press ends of headlamp cover tab to-
gether and remove high beam head-
lamp cover 2.

Pull the electrical connector off.

Turn locking mechanism 5 counter-
clockwise and take out the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Turn locking mechanism 5 clockwise.

Plug the connector onto the bulb.

Align high beam headlamp cover 2
and click it into place.Parking and standing lamp bulbs

Press ends of cover tab together and
remove high beam headlamp cover 2.

Pull out bulb socket 6 with the bulb.

Pull the bulb out of bulb socket 6.

Insert a new bulb in bulb socket 6.

Reinstall bulb socket 6.

Align high beam headlamp cover 2
and click it into place.Additional turn signal lamp bulbs
The additional turn signal lamps in the
exterior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the turn signal unit replaced
by an authorized Mercedes-Benz Center.
Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.

396 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to posi-
tion M (
page 123).

Open the trunk (
page 108).
Tail lamp unit
1Backup lamp
2Turn signal lamp
3Driver’s side: Rear fog lamp
Passenger’s side: Substitute lamp

Fold the trim to the side and remove it.

Turn the bulb socket counterclockwise
and pull it out.

Gently push the bulb into the socket,
turn it counterclockwise and remove it.

Insert the new bulb and reinstall the
bulb socket.
The bulb socket should audibly click
into place.

Reinstall the trim.License plate lamp
1Screws

Loosen both screws 1.

Remove the license plate lamp.

Replace the bulb.

Reinstall the license plate lamp.

Retighten screws 1.

404 Practical hintsFlat tireMounting the spare wheel Preparing the vehicle
Prepare the vehicle as described
(
page 399).

Turn spare wheel bracket counter-
clockwise to loosen.

Take the spare wheel out of the trunk.
Lifting the vehicle

Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
(not included) or other sizable objects.
When changing wheel on a level sur-
face:
Place one wheel chock or other
sizable object in front of and anoth-
er wheel chock or sizable object be-
hind the wheel that is diagonally
opposite to the wheel being
changed.Always try lifting the vehicle using the
jack on a level surface. However,
should circumstances require you to do
so on a hill, place a wheel chock or oth-
er sizable object and the other wheel
chock or sizeable object as follows:

Place wheel chocks or other sizable
objects on the downhill side block-
ing both wheels of the axle not be-
ing worked on.

Take the vehicle tool kit and the jack
out of the storage compartment under
the trunk floor (
page 383).
Warning!
G
The dimensions of the spare wheel are dif-
ferent from those of the road wheels. As a
result, the vehicle handling characteristics
change when driving with a mounted spare
wheel. Adapt your driving style accordingly.
The spare wheel is for temporary use only.
When driving with spare wheel mounted, en-
sure proper tire inflation pressure and do
not exceed vehicle speed of 50 mph
(80 km/h).
Drive to the nearest Mercedes-Benz Center
as soon as possible to have the spare wheel
replaced with a regular road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a spare
wheel is mounted.

407 Practical hints
Flat tire

Keeping jack in this position, turn
crank3 clockwise until the jack base
meets the ground. Make sure the jack
is vertical (plumb line).

Continue to turn the crank until the tire
is a maximum of 1.2 in (3 cm) from the
ground.Removing the wheel
1Alignment bolt

Unscrew upper-most wheel bolt and re-
move.

Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.

Remove the remaining bolts.

Remove the wheel.Mounting the new wheel

Clean contact surfaces of wheel and
wheel hub.

Guide the spare wheel onto the align-
ment bolt and push it on.

Insert wheel bolts and tighten them
slightly.
!Do not place wheel bolts in sand or dirt.
This could result in damage to the bolt
and wheel hub threads.
Warning!
G
Inflate spare wheel tire only after the wheel
is properly mounted.
Inflate the spare wheel tire using the electric
pump (
page 408) before
lowering the ve-
hicle.
Warning!
G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.


410 Practical hintsFlat tire
Detach the electric air pump.

Stow the electrical plug and the air
hose behind the flap and place the air
pump back in the trunk.Lowering the vehicle

Lower vehicle by turning crank coun-
terclockwise until the full weight of the
vehicle is resting on the ground.

Pull the jack out of the jack support
tube.
1 - 5 Wheel bolts

Tighten the five wheel bolts evenly, fol-
lowing the diagonal sequence illustrat-
ed (1 to 5), until all bolts are tight.
Observe a tightening torque of 96 lb-ft
(130 Nm).
Warning!
G
Follow recommend inflation pressures.
Do not overinflate tires. Overinflating tires
can result in sudden deflation (blowout) be-
cause they are more likely to become punc-
tured or damaged by road debris, potholes,
etc.
Do not underinflate tires. Underinflated tires
wear unevenly, adversely affect handling
and fuel economy, and are more likely to fail
from being overheated.
iThe flat tire may be transported in the
trunk when the retractable hardtop is
raised. Use the protective sheet provid-
ed with the spare wheel. Do not acti-
vate the tire inflation pressure monitor
until the deflated tire has been re-
moved from the vehicle.


463 Index
C
CAC 453
California retail buyers and lessees, impor-
tant notice for 11
Call priority, Tele Aid 244
CAN System 454
Capacities and recommended
fuel/lubricants 445
Cargo area see Trunk
Carpets, cleaning 330
Catalytic converter 267
CD changer 142
CD player 142
Operating 142
Center console
Lower part 30
Upper part 29
Central locking
Automatic 112, 155
Central locking/unlocking switch 29,
113
Locking/unlocking from inside 113
Certification label 430
Check engine see Lamps, indicator and
warningChildren in the vehicle
Airbags 66
Indicator lamp, front passenger front
airbag 78
Infant and child restraint systems 64,
76
Cigarette lighter 234
Clock 23, 150
Cockpit 22, 454
Cockpit Management and Data System
see COMAND system
Cold tire inflation pressure 310, 454
Collapsible tire 454
COMAND system 29, 454
Driving instructions 266
Combination switch
High beam 53, 129
Turn signals 53
Windshield wipers 54
Consumer battery 279
Control and operation of radio
transmitters 266
Control system 135, 138, 454Control system menus
AUDIO 141
NAV 143
Settings 146
Standard display 140
TEL* 159
Trip computer 157
Vehicle status message memory 144
Control system submenus 139
Convenience 156
Instrument cluster 149
Lighting 152
Time 150
Vehicle 155
Controller Area Network see CAN System
Convenience feature 200
Coolant 450
Anticorrosion/antifreeze mixing ratio
and quantity 451
Checking coolant level 278
Coolant warning lamp 336
Messages in the multifunction
display 365, 366, 367, 368
Temperature 268
Temperature gauge 133

464 IndexCorner-illuminating front fog lamps* 127
Replacing bulbs 391
Courtesy lighting 131
Cruise control 204, 454
Messages in the multifunction
display 349, 350
Cup holder 232
Cup holders
Cleaning 329
Curb weight 310, 454
Customer Assistance Center see CAC
D
Daytime running lamp mode 125
Setting 152
Deep water see Standing water
Defogging, Windshield 187
Defrosting, Front 186
Defrosting, Rear 179
Delayed switch-off
Exterior lamps 154
Interior lighting 155
Department of Transportation see DOT
Difficulties
While driving 56
With starting the engine 50
Digital clock see ClockDigital speedometer 140
Dimensions, Vehicle 443
Direction of rotation (tires) 284
Displays
Digital speedometer 140
Distronic* 209
Maintenance service indicator 318
Multifunction display 135
Outside temperature 134, 140
Symbol messages 359
Text messages 347
Vehicle status message memory 144
Vehicle status messages 345
Distance to empty (range), Trip
computer 158
Distance warning function* 215
Activating 216
Deactivating 216
Intermittent warning sound 215
Symbol 143, 211
Distronic indicator lamp* 25Distronic* 207, 454
“Resume” function 214
Activating 212
Cleaning system sensor cover 325
Control system 143, 211
Distance warning function 215
Driving hints 216
System sensor cover 325
Warning and indicator lamps 209,
215, 338
Door
Control panel 32
Handle, Inside 32
Locking/unlocking,
KEYLESS-GO* 35, 62
Locking/unlocking, Mechanical
key 385, 387
Locking/unlocking, SmartKey 34, 62
Messages in the multifunction
display 369
Opening from inside 107
Storage compartment 228
Door control panel 32
Door handle 32
DOT 311, 454
Drinking and driving 257