2006 MERCEDES-BENZ G55AMG rims

Contents
Technical data.................................. 365
Parts service ...................................... 366
Warranty coverage ............................. 367
Loss of Service and Warranty
Information Booklet...................... 367
Identification labels............................ 368
Layout of poly-V-belt drive ................. 369
G 500 ........................................... 369
G 55 AMG..................................... 369
Engine ................................................ 370
Rims and tires .................................... 371
Rims and Tires.............................. 372
Spare wheels ................................ 373
Electrical system................................ 374
Main dimensions, vehicle weights
and ratings ......................................... 375
Main dimensions .......................... 375
Vehicle weights and ratings ......... 375Fuels, coolants, lubricants, etc. ......... 376
Capacities .................................... 376
Engine oils.................................... 377
Engine oil additives ...................... 378
Air conditioning refrigerant .......... 378
Brake fluid .................................... 378
Premium unleaded gasoline ......... 378
Fuel requirements ........................ 379
Gasoline additives ........................ 379
Coolants....................................... 380
Anticorrosion/antifreeze.............. 381
Windshield/rear window
washer system and headlamp
cleaning system ........................... 382Technical terms............................... 383
Index................................................. 389

66 Safety and Security
Occupant safety
Safety guidelines for the seat belt,
emergency tensioning device and
airbag Your vehicle was originally equipped
with airbags that are designed to acti-
vate in certain impacts exceeding a
preset threshold to reduce the poten-
tial and severity of injury. It is important
to your safety and that of your passen-
ger that you replace deployed airbags
and repair any malfunctioning airbags
to make sure the vehicle will continue
to provide supplemental crash protec-
tion for occupants.
Warning!G

Damaged seat belts or belts that were
highly stressed in an accident must be
replaced and their anchoring points
must also be checked. Use only belts in-
stalled or supplied by an authorized
Mercedes-Benz Light Truck Center.

No modifications of any kind may be
made to any components or wiring of
the SRS. This includes changing or re-
moving any component or part of the
SRS, the installation of additional trim
material, badges, etc. over the steering
wheel hub, passenger front airbag cov-
er, outboard sides of the front seat
backrests, door trim panels, or door
frame trims, and installation of addition-
al electrical /electronic equipment on or
near SRS components and wiring. Keep
area between airbags and occupants
free from objects (e.g. packages, purs-
es, umbrellas, etc.).

Airbags and emergency tensioning de-
vices (ETDs) are designed to function on
a one-time-only basis. An airbag or ETD
that was activated must be replaced.

Do not pass belts over sharp edges.
They could tear.

Do not make any modification that could
change the effectiveness of the belts.

Do not bleach or dye seat belts as this
may severely weaken them. In a crash
they may not be able to provide ade-
quate protection.

Never place your feet on the instrument
panel, dashboard, or on the seat. Always
keep both feet on the floor in front of the
seat.

Airbag system components will be hot
after an airbag has inflated. Do not
touch.

229 Operation
Driving instructions
Checklist before off-road driving
Engine oil level

Check the engine oil level
(
page 244). The display ENGINE OIL
LEVEL - OK
must appear in the multi-
function display.
Only then can the vehicle obtain a trou-
ble-free oil supply, even on steep gradi-
ents.
Tires

Check the tread depth and maintain
specified tire inflation pressure
(a placard with the recommended tire
inflation pressures is located on the
driver’s door B-pillar (
page 255)).

Check tires for possible damage and
remove foreign objects.

Replace missing valve caps.Rims

Dented or bent rims can cause tire in-
flation pressure loss and damage the
tire beads. For this reason, check and,
if necessary, change rims before driv-
ing off-road.
Vehicle tool kit

Check if the vehicle jack is functional.

In all cases take the vehicle tool kit, a
strong tow rope, a shovel, and a small
plank (to put under the vehicle jack on
sandy soil) with you.

Avoid excessive engine
speeds – drive at moderate engine
speeds (max. 3000 rpm).

Before driving through water, deter-
mine its depth.

Do not stop vehicle while immersed
in water, and do not shut off the en-
gine.

In sandy soil, drive at a steady
speed as allowed by conditions.
This helps overcome the vehicle
rolling resistance and reduces the
likelihood of the vehicle sinking into
the ground.

Do not initiate jumps with the vehi-
cle. It interrupts the forward mo-
mentum of the vehicle.

Always drive on slopes with the en-
gine running and the vehicle in
gear.

Inspect the vehicle for possible
damage after each off-road trip.

252 Operation
Tires and wheels
See an authorized Mercedes-Benz Light
Truck Center for information on tested and
recommended rims and tires for summer
and winter operation. They can also offer
advice concerning tire service and
purchase.
Retreaded tires are not tested or recom-
mended by Mercedes-Benz, since previous
damage cannot always be recognized on
retreads. The operating safety of the
vehicle cannot be assured when such tires
are used.Important guidelines

Only use sets of tires and rims of the
same type and make.

Tires must be of the correct size for the
rim.

Break in new tires for approximately
60 miles (100 km) at moderate
speeds.

Regularly check the tires and rims for
damage. Dented or bent rims can
cause tire inflation pressure loss and
damage to the tire beads.

If vehicle is heavily loaded, check tire
inflation pressure and correct as
required.

Do not allow your tires to wear down
too far. Adhesion properties on wet
roads are sharply reduced at tread
depths under
1/8in (3 mm).

When replacing individual tires, you
should mount new tires on the front
wheels first (on vehicles with
same-sized wheels all around).
Warning!G
Replace rims or tires with the same designa-
tion, manufacturer and type as shown on the
original part. See an authorized
Mercedes-Benz Light Truck Center for fur-
ther information. If incorrectly sized rims
and tires are mounted:

The wheel brakes or suspension
components can be damaged.

The operating clearance of the wheels
and the tires may no longer be correct.
Warning!G
Worn, old tires can cause accidents. If the
tire tread is badly worn, or if the tires have
sustained damage, replace them.
When replacing rims, only use genuine
Mercedes-Benz wheel bolts specified for the
particular rim type. Failure to do so can
result in the bolts loosening and possibly an
accident.

263 Operation
Tires and wheels
Overinflated tire inflation pressure
Overinflated tires can:

adversely affect handling
characteristics

cause uneven tire wear

be more prone to damage from road
hazards

adversely affect ride comfort

increase stopping distance
Tire labeling
Besides tire name (sales designation) and
manufacturer name, a number of markings
can be found on a tire.
Following are some explanations for the
markings on your vehicle’s tires:1Uniform Quality Grading Standards
(
page 271)
2DOT, Tire Identification Number (TIN)
(
page 268)
3Maximum tire load (
page 269)
4Maximum tire inflation pressure
(
page 270)
5Manufacturer
6Tire ply material (
page 273)
7Tire size designation, load and speed
rating (
page 264)
8Load identification (
page 267)
9Tire name
Warning!G
Follow recommended tire inflation
pressures.
Do not overinflate tires. Overinflated tires
can adversely affect handling and ride
comfort, wear unevenly, increase stopping
distance, and result in sudden deflation
(blowout) because they are more likely to
become punctured or damaged by road
debris, potholes etc.
i
For illustration purposes only. Actual
data on tires are specific to each vehi-
cle and may vary from data shown in
above illustration.
For more information, see “Rims and
tires” (
page 371).

265 Operation
Tires and wheels
Rim diameter
The rim diameter4 (
page 264) is the
diameter of the bead seat, not the
diameter of the rim edge. Rim diameter is
indicated in inches (in).
Tire load rating
The tire load rating5 (
page 264) is a
numerical code associated with the
maximum load a tire can support.
For example, a load rating of 91 corre-
sponds to a maximum load of 1 356 lbs
(615 kg) the tire is designed to support.
See also “Maximum tire load”
(
page 269) where the maximum load
associated with the load index is indicated
in kilograms and lbs.For additional information on tire load
rating, see “Load identification”
(
page 267).
Warning!G
The tire load rating must always be at least
half of the GAWR (
page 274) of your vehi-
cle. Otherwise, tire failure may be the result
which may cause an accident and/or seri-
ous personal injury to you or others.
Always replace rims and tires with the same
designation, manufacturer and type as
shown on the original part.
Warning!G
Do not overload the tires by exceeding the
specified load limit as indicated on the plac-
ard located on the driver’s door B-pillar.
Overloading the tires can overheat them,
possibly causing a blowout. Overloading the
tires can also result in handling or steering
problems, or brake failure.
i
Tire load rating5 (page 264) and
Tire speed rating6 (
page 264) are
also referred to as “service descrip-
tion”.

277 Operation
Tires and wheels
Rotate tires before the characteristic tire
wear pattern becomes visible (shoulder
wear on front tires and tread center wear
on rear tires).
Thoroughly clean the mounting face of
wheels and brake disks, i.e. the inner side
of the wheels/tires, during each rotation.
Check for and ensure proper tire inflation
pressure.
For information on wheel change, see “Flat
tire” (
page 348).
Warning!G
Have the tightening torque checked after
changing a wheel. Wheels could become
loose if not tightened with a torque of
97 lb-ft (130 Nm).
Only use genuine Mercedes-Benz wheel
bolts specified for your vehicle’s rims.

288 Operation
Vehicle care
Upholstery
Using aftermarket seat covers or wearing
clothing that have the tendency to give off
coloring (e.g. when wet, etc.) may cause
the upholstery to become permanently dis-
colored. By lining the seats with a proper
intermediate cover, contact-discoloration
will be prevented.
Leather upholstery
Wipe leather upholstery with a damp cloth
and dry thoroughly or clean with
Mercedes-Benz approved Leather Care.
Exercise particular care when cleaning per-
forated leather as its underside should not
become wet.Cloth upholstery
Clean with soft bristle brush, or use a
dry-shampoo cleaner in case of excessive
dirt.
MB Tex upholstery
Pour Mercedes-Benz approved Interior
Care onto soft lint-free cloth and apply
with light pressure.
Plastic and rubber parts
Do not use oil or wax on these parts.Illuminated door sill panels
Use a gentle dishwashing detergent or
mild detergent for delicate fabrics as a
washing solution. Wipe with a cloth moist-
ened in lukewarm solution. Do not use
scouring agents.
Wood trims
Dampen cloth using water and use damp
cloth to clean wood trims in your vehicle.
Do not use solvents like tar remover or
wheel cleaner nor polishes or waxes as
these may be abrasive.