2006 MERCEDES-BENZ E350 4MATIC program

297 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed signal trans-
mitter button (2, 3 or4).
Step 13:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the
integrated signal transmitter to pick up the
signal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:

Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.
iSome garage door openers (or other
rolling code equipped devices) may
require you to press, hold for 2 seconds
and release the same signal transmit-
ter button a third time to complete the
training process.

298 Controls in detailUseful features
Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (
page 36).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the signal transmitter button, pro-
ceed with programming starting with
step 3.Operation of integrated remote control

Switch on the ignition (
page 36).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
iUpon completion of programming the
integrated remote control, make sure
you retain the hand-held remote con-
trol that came with the garage door
opener, gate operator or other device.
You may need it for use in other vehi-
cles, for future programming of an
integrated remote control, or simply for
continued use as a hand-held remote
control to operate the respective
device in other situations.

299 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on the ignition (
page 36).

Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.


Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.


While performing step 3, hold the
hand-held remote control6 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes
of all three channels.
iCertain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Center, or call Mercedes-Benz
Customer Assistance Center (in the
USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.

302 OperationIn the “Operation” section you will find de-
tailed information on operating, maintain-
ing and caring for your vehicle.The first 1 000 miles (1 500 km)
The more cautiously you treat your vehicle
during the break-in period, the more satis-
fied you will be with its performance later
on.

Drive your vehicle during the first
1 000 miles (1 500 km) at varying but
moderate vehicle and engine speeds.


During this period, avoid heavy loads
(full throttle driving) and excessive en-
gine speeds (no more than
2/3 of
maximum rpm in each gear).


Avoid accelerating by kick-down.


Do not attempt to slow the vehicle
down by shifting to a lower gear using
the selector lever.


Select positions3, 2 or1 only when
driving at moderate speeds (for hill
driving).


SelectC as the preferred shift program
(page 189) for the first 1 000 miles
(1 500 km).After 1 000 miles (1 500 km) you may
gradually increase vehicle and engine
speeds to the permissible maximum.
All of the above, as may apply to your vehi-
cle type, also apply when driving the first
1 000 miles (1 500 km) after the engine or
the rear differential has been replaced.
!Additional instructions for AMG vehi-
cles:

During the first 1000 miles
(1500 km), do not exceed a speed
of 85 mph (140 km/h).


During this period, avoid engine
speeds above 4500 rpm in each
gear.
iAlways obey applicable speed limits.

497 Technical terms
Power train
Collective term designating all compo-
nents used to generate and transmit
motive power to the drive axles, includ-
ing:


Engine


Clutch/torque converter


Transmission


Transfer case*


Drive shaft


Axle shafts/axles
Production options weight
(
page 355)
Program mode selector switch
Used to switch the automatic transmis-
sion between standard operationS and
operationC.PSI
(P
ounds per s
quare i
nch)
(
page 355)
Recommended tire inflation pressure
(page 355)
Restraint systems
Seat belts, belt tensioners, air bags and
child restraint systems. As indepen-
dent systems, their protective func-
tions complement one another.
Rim
(page 355)
RON
(Research O
ctane N
umber)
The Research Octane Number for gaso-
line as determined by a standardized
method. It is an indication of a gaso-
line’s ability to resist undesired detona-
tion (knocking). The average of both
the ->MON (Motor Octane Number)
and RON (Research Octane Number) is
posted at the pump, also known as
ANTI-KNOCK INDEX.Shift lock
When the vehicle is parked, this lock
prevents the transmission selector le-
ver from being moved out of positionP
without the ignition or engine on and
brake pedal depressed.
Sidewall
(
page 355)
SRS
(Supplemental R
estraint S
ystem)
Seat belts, emergency tensioning de-
vice and air bags. Though independent
systems, they are closely interfaced to
provide effective occupant protection.

501 Index
A
ABS 92, 493
Indicator lamp 374
Messages in display
Accelerator position
Automatic transmission 186
Accessory weight 353
Accident 59
Active head restraints 77
Air bags 67
Children 68
Front, Driver 71
Front, Passenger 71
Safety guidelines 70
Side impact 72
Window curtain 72
Air conditioning refrigerant 487
Air conditioning system see Climate con-
trol system
Air conditioning, Cooling 212, 227
Air distribution 208, 222Air pressure 353
Air pressure see Tire inflation
pressure 339
Air pump, electric
Turning on 446
Air recirculation mode 210, 224
Air vents 208, 222
Air volume 209, 223
Airmatic DC (Dual Control)* 259, 493
Messages in display 420
Suspension tuning 259
Vehicle level control 260
Alarm system see Anti-theft systems
Alignment bolt (vehicle tool kit) 424,
444, 493
Anticorrosion/antifreeze 490
Antilock Brake System see ABS
Anti-theft systems 101
Anti-theft alarm system 101
Immobilizer 101
Tow-away alarm 103
Aquaplaning see Hydroplaning 307Ashtray 281
Aspect ratio 353
AUDIO menu 159
Selecting radio station 159
Selecting satellite radio* station 160
Audio system
CD mode 160
Auto-dimming
Rear view mirrors 197
Automatic central locking, Control
system 174
Automatic headlamp mode 142
Automatic lighting control, Interior
lighting 147
Automatic locking when driving 174
Automatic shift program, Automatic
transmission 189
Automatic transmission 183
Accelerator position 186
Emergency operation (Limp Home
Mode) 196
Gear ranges 188
Gear selector lever one-touch
gearshifting 190
Gear selector lever position 183, 185

502 Index
Gear shifting malfunctions 196
Kickdown 186
Kickdown, Manual shift program
E55AMG 195
Manual (One-touch) gearshifting 190
Manual shift program E 55 AMG 193
Shift program mode selector
switch 189
Shift program mode selector switch,
Manual shift program
E55AMG 193
Starting engine 50
Steering wheel gearshift control
one-touch gearshifting
E55AMG 191
Winter program mode 189
B
Backrest 271
Seat 41
Seat, multicontour 134
Backup lamps
Messages in display 412
Replacing bulbs 433
Bar 354
BAS 94, 493Batteries, SmartKey
Changing 431, 432
Checking battery condition 110, 116
Batteries, SmartKey with KEYLESS-GO*
Changing 431, 432
Checking battery condition 116
Batteries, Vehicle
Charging 452
Disconnecting 451
Installing 452
Jump starting 454
Messages in display 389, 398, 399
Reconnecting 453
Removing 452
Bead 354
Beverage holder see Cup holders
Bi-Xenon headlamps* see Headlamps
Bleeding the fuel system 449
Block heater* (Canada only) 359
Brake Assist System see BAS
Brake fluid
Checking 318
Messages in display 402Brake lamp
Cleaning lenses 367
Messages in display 412
Replacing bulbs 433
Brake pads
Message in display 400
Brakes 304
Warning lamp 376
Break-in period 302
Bulbs see Replacing bulbs
C
CAC 493
California retail buyers and lessees, impor-
tant notice for 11
Can holder see Cup holders
CAN system 493
Capacities and recommended
fuel/lubricants 484
Cargo area see Trunk
Cargo tie-down rings 275
Carpets, cleaning 371
Catalytic converter 312
CD player 160

505 Index
Drive-Dynamic seat* with multicontour
features 134
Massage function 135
Driving
Abroad 311
Hydroplaning 307
In winter 309
Instructions 47, 303
Problems 58
Safety systems 92
Through standing water 310
With Distronic* 257
Driving safety systems
4MATIC 100
ABS 92
BAS 94
Electrohydraulic brake system 97
ESP
®
94, 494
E
Easy-entry/exit feature 43, 175
Electrical fuses see Fuses
Electrical system, Technical data 481Electrohydraulic brake system 494
Activating/deactivating 98
Driving hints 99
Messages in display 400, 401
Self-check 99
Warning lamp 97
Electronic Stability Program see
ESP
®
94, 494
Emergency calls
Tele Aid calls 287
Emergency operation (Limp Home
Mode) 196
Emergency operations 427
Fuel filler flap 428
Gear selector lever, Unlocking 428
Locking/unlocking the vehicle 426
Remote door unlock 292
Tilt/sliding sunroof* or tilt/sliding pan-
el*, Manual operation 429
Trunk lid, Releasing from inside 127
Trunk lid, Unlocking 427
Emergency tensioning device see ETDEmergency, In case of
Battery, Jump starting 454
First aid kit 422
Flat tire, changing 441
Fuses
Hazard warning flasher 146
Instrument cluster, Indicator
lamps 374, 375, 376, 377, 378,
379, 380, 381, 383
Roadside Assistance 12
Towing the vehicle 457
Emission control 313
Emission control information label 468
Emission control system warranties 10
Emission control vacuum line routing dia-
gram label 468