2006 MERCEDES-BENZ CLS500 remote control

271 Controls in detail
Useful features
Programming the integrated remote
control
Step 1:
Switch on the ignition (
page 36).
Step 2:

If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:

Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping the indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
The indicator lamp1 will flash, first
slowly and then rapidly.
When programming a garage door opener, it
is advised to park outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.


272 Controls in detailUseful featuresStep 5:
After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.
If the indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and
released.Step 7:

To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:

Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the
“training” button may also be referred
to as “learn”or “smart” button. If there
is difficulty locating the transmitting
button, refer to the garage door opener
operator’s manual.
iThe indicator lamp1 flashes immedi-
ately the first time the signal transmit-
ter button is programmed. If this button
has already been programmed, the in-
dicator lamp will only start flashing af-
ter 20 seconds.
iIf the indicator lamp1 flashes rapidly
for about 2 seconds and then turns to a
constant light, continue with
programming steps 8 through 12 as
your garage door opener may be
equipped with the “rolling code”
feature.


274 Controls in detailUseful featuresStep 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 36).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the signal transmitter button, pro-
ceed with programming starting with
step 3.
Operation of integrated remote control

Switch on the ignition (
page 36).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
iUpon completion of programming the
integrated remote control, make sure
you retain the hand-held remote con-
trol that came with the garage door
opener, gate operator or other device.
You may need it for use in other vehi-
cles, for future programming of an
integrated remote control, or simply for
continued use as a hand-held remote
control to operate the respective
device in other situations.

275 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on the ignition (
page 36).

Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:


Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.


Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.


While performing step 3, hold the
hand-held remote control6 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes
of all three channels.

276 Controls in detailUseful features
iCertain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Center, or call Mercedes-Benz
Customer Assistance Center (in the
USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.
iUSA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any
interference received, including
interference that may cause
undesired operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.
iCanada only:
This device complies with RSS-210 of
Industry Canada. Operation is subject
to the following two conditions:
(1) This device may not cause interfer-
ence, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation of the device.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.

290 OperationAt the gas stationRefueling
The fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking / unlocking the vehicle with
the remote control automatically
locks / unlocks the fuel filler flap.1To open the fuel filler flap
2Fuel filler cap
3To insert the fuel filler cap

Turn the engine off

by turning the SmartKey to
position0.


by pressing the KEYLESS-GO*
start/stop button. Open the driv-
er’s door (with the driver’s door
open, starter switch is now in
position0, same as SmartKey
removed from starter switch).

Remove the SmartKey from the starter
switch.

Open the fuel filler flap by pushing at
the point indicated by the arrow1.
The fuel filler flap springs open.

Turn the fuel cap to the left and hold on
to it until possible pressure is released.

Take off the cap and set it in direction
of arrow2 in the recess3 on the fuel
filler flap.
To prevent fuel vapors from escaping
into open air, fully insert filler nozzle
unit.

Only fill your tank until the filler nozzle
unit cuts out – do not top up or over-
fill.
Warning!
G
Gasoline fuel is highly flammable and poi-
sonous. It burns violently and can cause
serious injury. Whenever you are around
gasoline fuel, avoid inhaling fumes and skin
contact, extinguish all smoking materials.
Never allow sparks, flame or smoking mate-
rials near gasoline fuel!

483 Index
Door
Entry lamps 143
Message in display 382
Remote door unlock (Tele Aid) 269
Door control panel 32
Door handle 32
Doors
Opening from inside vehicle 111
DOT 332, 473
Drinking and driving 279
Drive-dynamic seat* 127
Driving
Abroad 287
Hydroplaning 283
In winter 285
Instructions 46
Problems 56
Safety systems 84
Systems 222
Through standing water 287
Driving hints
Electro-hydraulic brake system 92
Driving instructions 279
Driving off 282Driving safety systems
ABS 84
BAS 86
Electro-hydraulic brake system 89
ESP
®
86, 473
Driving systems 222
Airmatic DC 238
Cruise control 222
Distronic* 226
Driving safety systems 84
Vehicle level control 239
DTR see Distronic*
Dual control
Airmatic DC 238
E
Easy-entry/exit feature* 42
Electric air pump 427
Electrical fuses see fuses
Electrical system, Technical data 458Electro-hydraulic brake system 89, 476
Activation 90
Deactivation 91
Driving hints 92
Messages in display 375, 376
Self-check 91
Warning lamp 89
Electronic Stability Program see ESP
®
Emergency calls
Tele Aid calls 263
Emergency operation
(Limp-Home Mode) 190
Emergency operations 406
Fuel filler flap 404
Gear selector lever, Unlocking 404
Locking/unlocking the vehicle 402
Power tilt/sliding sunroof,
manual operation 406
Remote door unlock 269
Trunk lid, Releasing trunk from
inside 120
Trunk lid, Unlocking 403
Emergency tensioning device see ETD

486 IndexHood 293
Message in display 384
HVAC see 4-zone automatic climate
control
Hydroplaning 283
I
Identification labels 446
Identification Number, Vehicle (VIN) 446
Ignition 36, 38, 50
Immobilizer 93
Indicator lamps see Lamps, indicator and
warning
Infant and child restraint systems see
Children in the vehicle
Information
About service and warranty 10
Button for Tele Aid 267
Inside door handle 111
Inside rear view mirror
Antiglare 191Installing
Infant and child restraint systems 80
Towing eye bolt 439
Wiper blades 418
Instrument cluster 24, 144, 474
Cleaning 349
Coolant temperature gauge 145
Illumination 144
Multifunction display 147
Outside temperature indicator 146
Interior lighting 141
Delayed switch-off 167
Interior rear view mirror 44
J
Jack 398, 399
Jacking up the vehicle 425
Jump starting 435K
Key, Mechanical 402
Key, SmartKey
Changing batteries 408
Key, SmartKey with KEYLESS-GO*
Changing batteries 409
KEYLESS-GO* 110, 474
Activating ignition with 38
Closing
Trunk 117
Factory setting 107
Global locking 107
Global unlocking 107
Important notes 105
Remote controls 103
Starting the engine 50
Turning off engine 60
Unlocking and opening, trunk 110
Unlocking with 35
Kickdown 180, 474
Kilopascal 333