2006 MERCEDES-BENZ C55AMG remote control

273 Controls in detail
Useful features
Garage door opener
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated re-
mote control
1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
ton
i
When the anti-theft alarm* or the
tow-away alarm* (if equipped) stays on
for more than 30 seconds, a call is ini-
tiated automatically to the Response
Center. See “Anti-theft alarm system*”
(
page 88) and “Tow-away alarm*”
(
page 90).
Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
- signaling the door to stop and reverse -
does not meet current U.S. federal safety
standards.


274 Controls in detail
Useful features
Programming the integrated remote
control
Step 1:
Switch on the ignition (page 33).Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.Step 3:Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to 12 cm) away from the signal
transmitter button (2, 3 or4) to be
programmed, while keeping the indica-
tor lamp1 in view.
Step 4:
Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
The indicator lamp1 will flash, first
slowly and then rapidly.
When programming a garage door opener
park the vehicle outside the garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon monoxide
(CO), and inhaling it can cause unconscious-
ness and possible death.

275 Controls in detail
Useful features
Step 5:
After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.Step 6:
Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.
If the indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.Step 7:To program the remaining two signal
transmitter buttons, repeat the steps
above starting with step 3.
Rolling code programming
To train a garage door opener (or other
rolling code devices) with the rolling code
feature, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
i
The indicator lamp1 flashes immedi-
ately the first time the signal transmit-
ter button is programmed. If this button
has already been programmed, the in-
dicator lamp will only start flashing af-
ter 20 seconds.
i
If the indicator lamp1 flashes rapidly
for about 2 seconds and then turns to a
constant light, continue with
programming steps 8 through 12 as
your garage door opener may be
equipped with the “rolling code”
feature.

277 Controls in detail
Useful features
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.
While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.
Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Switch on the ignition (page 33).
Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.
The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the signal transmitter button, pro-
ceed with programming starting with
step 3.
Operation of integrated remote control
Switch on the ignition (page 33).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
i
Upon completion of programming the
integrated remote control, make sure
you retain the hand-held remote con-
trol that came with the garage door
opener, gate operator or other device.
You may need it for use in other vehi-
cles, for future programming of an
integrated remote control, or simply for
continued use as a hand-held remote
control to operate the respective
device in other situations.

278 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on the ignition (page 33).
Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.

Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.

While performing step 3, hold the
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.

If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.

Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
i
If you sell your vehicle, erase the codes
of all three channels.
i
Certain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Center, or call Mercedes-Benz
Customer Assistance Center (in the
USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.

452 Index
Control system submenus 127, 129
Convenience 148
Instrument cluster 138
Lighting 144
Time/Date 140
Vehicle 147
Controller Area Network see CAN system
Coolant 301, 439
Anticorrosion/antifreeze
quantity 440
Capacities 436
Checking coolant level 295, 301
Messages in display 367–369
Temperature 292
Temperature gauge 25, 123
Cruise control 245, 444
Message in display 370
Cup holder 258, 260
Cleaning 346
Curb weight 332
Customer Assistance Center see CACD
Date display, setting 142, 143
Daytime running lamp mode 116
Setting 144
Deep water see Standing water
Defogging windshield
Automatic climate control*
(Canada only) 191
Climate control 180
Defrosting, Front
Automatic climate control*
(Canada only) 190
Climate control 179
Defrosting, Rear 173
Delayed shut-off
Exterior lamps 146
Interior lighting 147
Department of Transportation see DOT
Difficulties
While driving 52
With starting 46
Digital clock see clock
Digital speedometer 130
Dimensions, vehicle 435
Direction of rotation (tires) 308Displays
Digital speedometer 130
Maintenance service indicator 338
Messages in display 370
Multifunction display 125
Outside temperature 130
Symbol messages 365
Text messages 360
Vehicle status messages
memory 135, 358
Distance to empty (range),
Trip computer 151
Door control panel 30
Doors
Entry lamps 121
Locking/unlocking, SmartKey 94
Message in display 370
Opening from inside/outside 96, 99
Remote door unlock (Tele Aid*) 272
Unlocking, Mechanical key 386
DOT 332
Downhill driving
Cruise control 246
Drinking and driving 283

453 Index
Driving
Abroad 290
Hydroplaning 287
In winter 288
Instructions 42, 283
Problems 52
Safety systems 82
Systems 245
Through standing water 289
Driving safety systems
ABS 82
BAS 84
ESP
®84
E
Easy-entry/exit feature 39, 148
Electrical fuses see Fuses
Electrical outlet 263
Electrical system, Technical data 434
Electronic Stability Program see ESP
®
Emergency calls
911 calls 235
Tele Aid* calls 266, 267, 271
Emergency operation
(Limp-Home Mode) 168Emergency operations
Gear selector lever, Unlocking 388
Locking/unlocking the vehicle 386
Power tilt/sliding sunroof*,
Manual operation 389
Remote door unlock 272
Trunk lid, Releasing from inside 102
Trunk lid, Unlocking 387
Emergency Tensioning Device see ETD
Emergency, in case of
Battery, Jump starting 415
First aid kit 350, 380
Flat tire, Changing 404
Fuses 420
Hazard warning flasher 119
Instrument cluster,
Indicator lamps 350–356
Roadside Assistance 12, 268
Towing the vehicle 417
Emission control 291
Information label 426
System warranties 10Engine
Belt layout 427
Block heater (Canada only) 337
Brake-in recommendations 282
Cleaning 343
Compartment 297
Malfunction indicator lamp 25, 352
Maximum engine speed 428
Number 426
Starting 46
Technical data 428
Turning 56
Engine coolant see coolant
Engine number 444
Engine oil 298, 437
Adding 300
Additives 437
Changing 436
Checking level 299
Consumption 298
Display messages 299
Filler neck 301
Messages in display 299, 371, 372
Recommended engine and
oil filter 371
Viscosity 444

456 Index
High mounted brake lamp 396
Hood 297
Message in display 373
Horn 23
HVAC see Climate control
Hydroplaning 287
I
Identification labels 426
Identification number, Vehicle (VIN) 426
Ignition 33, 46
Immobilizer 88
Indicator lamps see Lamps, indicator and
warning
Infant and child restraint systems see
Children in the vehicle
Inflation pressure see Tires, Inflation
pressures
Inside door handle 99
Instrument and controls see Instrument
clusterInstrument cluster 24, 122, 445
Cleaning 346
Illumination brightness 122
Lamps 350, 356
Messages in display see Malfunction
display messages
Multifunction display 125
Instrument lighting see Instrument cluster,
Illumination brightness
Instruments and controls see Cockpit
Interior lighting 120
Delayed shut-off 147
Interior rear view mirror 40
Auto-dimming mirrors* 169
Interior storage spaces see Storage
compartment
J
Jack 380
Jacking up the vehicle 405
Jump starting 415K
Key, mechanical 386
Key, SmartKey
Batteries 98
Battery check lamp 98
Changing batteries 393
Factory setting 96
Locking/unlocking 32, 96
Locking/unlocking, Global setting 96
Locking/unlocking, Selective
setting 96
Loss of 98
Messages in display 373
Opening and closing the power
windows 241
Opening and closing the tilt/sliding
sunroof* 241
Positions in starter switch 33
Remote control 94
Starting the engine 45
Turning off the engine 56
Unlocking, Trunk lid 98
Valet locking 103
Kickdown 158, 445
Kilopascal 332